Elvid FIELDVISION OCM-89-4KH Manuel utilisateur
QUICKSTART
GUIDE
FIELDVISION
OCM-89-4KH / 4KHS
8.9" Field Monitor
2
• Exposure to high sound levels
can cause permanent hearing
loss. Avoid listening at high
volumes for extended periods
of time.
• Keep this product away from
water and any ammable
gases or liquids.
• Do not expose this product
to humidity or extreme heat
or cold.
• Make sure this product is
powered off when plugging it
into a power source.
• Use only the correct,
recommended voltage.
• Do not attempt to disassemble
or repair this product.
• Do not place or store the
monitor facedown, since this
can damage the screen.
• Handle this product with care.
Avoid any impacts to this
product.
• Do not block the vents in this
product.
• Disconnect this product from
its power source before storage
and during electrical storms.
• Do not use chemical solutions
to clean this product. Clean it
with only a soft, dry cloth.
• Keep this product away from
children.
• Make sure that this product
is intact and that there are no
missing parts.
• To avoid damage to this
product, be careful not to
overtighten or improperly
thread any of the threaded
ttings.
• All images are for illustrative
purposes only.
PRECAUTIONS
3
BOX
CONTENTS
• Monitor
• Sun hood
• Sun-hood screws (×3)
• 12 V DC power supply
• Mini HDMI to HDMI cable
(C to A)
• Shoe-mount ball head
• V-mount battery sub plate
and mounting screws
• Hex key and set screw
4
OVERVIEW
IN SDI OUT USB IN HDMI OUT
DC 12V
BATTERY
RELEASE
1/4-20 threaded
mounting sockets
Battery slot
Battery release button
SDI input
(OCM-89-4KHS only)
SDI output
(OCM-89-4KHS only)
USB
port
Headphone output
HDMI input
HDMI output
DC 12 V power input
5
OCM-89-4KH
OCM-89-4KHS
F1 F2 EXIT MENUF1 F2 EXIT MENU
INPUT F1 EXIT/F2 MENUINPUT F1 EXIT/F2 MENU
Menu button
Menu button
Right selection button
Right selection button
Left selection button
Left selection button
Exit button
Exit / F2 button
F2 button
F1 button
F1 button
Input switch
Power button
Power button
Power indicator LED
Power indicator LED
1/4-20 socket
1/4-20 socket
6
GETTING
STARTED
INSTALLING THE BATTERY
1. Place an NP-F battery into the battery slot, making sure the
plate’s contacts align with the battery terminals.
2. Slide the battery toward the contacts until it locks into
place.
To remove the battery, press the battery release button and
slide the battery away from the contacts.
Important! The battery should easily slide into the battery slot.
Don’t use force to attach the battery. Doing so could damage
the battery or the contacts.
7
ATTACHING THE SUN HOOD
Use the sun hood to cut down on glare from sunlight or bright
overhead lighting.
1. Lay the monitor down on a at surface, with the screen
facing up.
2. Unfold the sun hood, and
attach it to the monitor’s
top and side 1/4-20
sockets with the three
sun-hood screws.
MOUNTING THE MONITOR ONTO A CAMERA
1. Determine the preferred monitor orientation, and screw the
ballhead into one of the 1/4-20 threaded sockets until it’s
tight.
2. Loosen the mounting shoe by turning the locking wheel
counterclockwise. Make sure the side tilt adjustment knob
is tight, and the ballhead is locked into place.
3. Fully insert the foot into the camera’s accessory shoe.
4. Tighten the locking wheel by turning it clockwise until it’s
secure.
5. To adjust the monitor’s position, hold the monitor while
loosening the tilt adjustment knob. Change the monitor’s
position, and tighten the tilt adjustment knob until the
monitor is secure.
8
CONNECTING TO A CAMERA
HDMI: Connect the monitor’s HDMI input to a camera with an
HDMI output.
SDI (OCM-89-4KHS only): Connect the monitor’s SDI input to a
camcorder or camera with an SDI output.
OUTPUTTING THE SIGNAL
Use the appropriate HDMI and SDI Out ports to connect the
FieldVision monitor to a recorder or external monitor.
Note: The HDMI and SDI Out ports are loop outputs. There is
no cross conversion between HDMI and SDI signals.
POWERING ON
1. Attach a battery, or plug the monitor into an AC outlet.
2. Press the power button.
9
USER
INTERFACE
ACCESSING THE MENUS
To get the most out of the monitor, make sure the its settings
are properly congured. All the setting congurations are
located in the six main menus: Image Adjust, Marker, Function,
Monitoring Tools, Audio, and System.
MENU NAVIGATION
Use the menu button to call up the menu and make selections,
and the and buttons to navigate the menu and adjust
values. Use the exit button to leave the menus and return to
the main view.
QUICK ADJUSTMENTS
Make quick adjustments to the Volume, Brightness, Contrast,
Saturation, Tint, and Sharpness settings anytime without
interrupting your workow.
Press the and buttons to adjust the volume output.
10
While the volume menu is on-screen, press the menu button
to cycle through other functions. When the desired function
menu appears on-screen, use the and buttons to adjust
the setting.
OCM-89-4KHS: The input button toggles the input signal
selector. Press the button to switch between HDMI and SDI
input signals.
Press Exit to close the menu and return to the main view.
FUNCTION BUTTONS
The two user-denable function buttons, F1 and F2, engage
monitor functions that can be programmed to accommodate
your specic needs.
By default, F1 is set to Peaking, and F2 is set to Level Meter.
When activated, the function buttons default to the settings in
the Peaking and Level Meter menus described below.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Elvid Moniteur
Elvid
Elvid OCM-10-PSM Manuel utilisateur
Elvid
Elvid OCM-7PWV Manuel utilisateur
Elvid
Elvid Studiovision STV-150-4KH Manuel utilisateur
Elvid
Elvid OCM-7B-D FieldVision Manuel utilisateur
Elvid
Elvid StudioVision STV-280-4KHDR Manuel utilisateur
Elvid
Elvid WCM-758G SkyVision Manuel utilisateur
Elvid
Elvid RigVision CM-7L Manuel utilisateur
Elvid
Elvid RIGVISION RVM-5P-HDR Manuel utilisateur
Elvid
Elvid OCM-101-4KH Manuel utilisateur
Elvid
Elvid OCM-7P-HDR Manuel utilisateur
