Elmes Electronic RP501 Manuel utilisateur
FOUR CHANNEL LOW POWER RADIO TRANSMISSION SET
WITH PROGRAMMABLE LOGIC AND HIGH SECURITY CODE RP501
A set consists of four-channel radio transmitter and dedicated receiver designed for use in radio remote control
and anti-burglar alarm systems. Both the transmitter (encoder) and the receiver (decoder) use microprocessor
controlled input/output logic and 64-bit coding technology. The system operates on SAW controlled 433,92 MHz
frequency and features up to 500 metres operating range in open field (with standard 20cm transmitter wire aerial).
Range up to 1000 metres in open field can be obtained with simple dipole TV UHF band (ch 21-60) directional
aerial and coaxial cable fixed to the receiver's pcb in place of the standard wire aerial. One receiver may operate
with many transmitters in a system.
The units are in same look like ABS plastic enclosures with different colour led indicators. The transmitter (red
led indicator) may be powered either from line 12VDC supply or, due to extremely low power requirements, from
internal 9V battery. The receiver's bicolour led indicator operates from line 12VDC supply and has four indepen-
dent relay outputs. The receiver has four fully programmable NO/NC relay outputs connecting to the receiver's
ground. The relay action is time-lapse mode depending on user's programming. The S output (open collector type) is
for external beeper device and delivers pulses on alarm state. The S output might also be user set to indicate the
radio link between transmitter and receiver failure. This is done by disconnecting jumper J5 on receiver’s board.
The receiver features built in bicolour led that provides necessary programming and output status indication. The
transmitter’s tamper switch, which is connected in series with D4 input, is user activated by cutting jumper ZT and
closing input D4 to the receiver's ground. It generates alarm transmission in channel 4 on opening of RP501 box.
Modes of operation of the RP501:
Mode 1. Continuous operation. Opening any of the transmitter's D1..D4 inputs
generates lasting 15 seconds transmission that switches to 1 second transmissions every 1
minute interval if any of the inputs remain still opened. Transmission ends when all inputs
of the transmitter are closed. Receiver resets outputs after passing user-programmed time.
Mode 2. Prolonged transmission operation. Transmission is prolonged of up to 15 or
40 seconds*, even if any of D1..D4 inputs are opened for a very short while. If the opened
any D input lasts over the set prolonged transmission period, the transmitter auto-switches
to battery saving mode of 1 second transmission every 1 minute stop time.
Mode 3. Radio relay operation. Any change on the D1..D4 inputs generates
transmission lasting 15 or 40* seconds with the receiver outputs status corresponding to
the status of the D inputs of the transmitter.
Mode 4. Radio relay operation with cyclic update. Same as mode 3 above with the
addition of 1 second lasting update transmission every 80 seconds.
In all the above modes of operation the transmitter's battery voltage is tested. It's drop to
7V is indicated by the receiver's green led blinking.
Additionally, operation of the set in any of the above modes may be performed with
radio link testing. Every 35 seconds transmitter sends a test signal. In case the receiver does
not get any test signal within 90 second time span it indicates that condition by blinking red
LED and delivering pulses (or continuous state if J5 is opened in receiver) to ground on S output. This
function is user set by disconnecting jumper (5-6). Only one transmitter may operate with radio link testing
in a system.
* 40 seconds with jumper 7-8 shorted, 15 seconds with jumper 7-8 opened.
Important! To ensure proper operation of the set in above selected modes it is necessary to perform instruction 3 of the
programming procedures below.
RP501 PROGRAMMING PROCEDURES
Prior to programming make sure the receiver's LED lights green, otherwise shortly disconnect the power supply.
1. Programming - learning transmitter(s) to receiver's memory:
a) press receiver's PRG switch (LED lights red) for less than 3 seconds. Releasing the switch LED continues to light red
indicating entering the programming mode of the decoder,
b) disconnect one of D inputs of the transmitter once, blinking receiver's LED confirm end of the procedure and the
transmitter is receiver's memory.
2. Programming - setting the receiver to time-lapse output mode and reset time:
a) press receiver's
PRG switch (LED lights red) for more than 3 and less than 8 seconds. Releasing the switch LED light
changes to green indicating entering this programming mode,
b) press shortly PRG switch again to start time-lapse count. Receiver's LED lights red.
c) when desired time has lapsed (up to 6 hours) press the PRG switch shortly again. The receiver's LED changes to green
and after 2 seconds starts blinking confirming end of the procedure.
8
21
8
21
8
21
8
21
5
By pressing PRG switch triple in shorter than 2 seconds intervals in point 2.b above, the receiver's outputs are set to latched
(on/off) mode of operation so their reset can only be made by disconnecting power supply from receiver.
3. Programming - setting the receiver to the transmitter's selected mode of operation:
a) set the required mode of operation in first transmitter* in the system,
b) perform learning the transmitter to the receiver's memory as described in point 1 above.
* the transmitter first entered to the receiver's memory.
4. Programming - erasing all transmitters from the receiver's memory:
press receiver's
PRG switch (LED lights red) for more than 8 seconds, until the receiver LED starts blinking confirming
end of the procedure. Memory of the receiver is cleared.
Wiring diagram of RP501:
+
D1D2D3D4
Transmitter
_
6M8
BAT 9V if powered by
Do not use battery
Power supply
12VDC
+
_
12VDC line !
+
D1D2D3D4 S
Receiver
_
12V
+_
Relay outputs
NO/NC select
+4.8V
solder joints
Unused transmitter inputs must be connected to receiver's ground (-V). When receiver is powered by
12VDC line remove battery otherwise the battery may be damaged.
SPECIFICATIONS:
* ASK radio high security code (64 bit) receiver/transmitter set,
* EC standard 433,92 MHz, four channel transmitter,
* up to 500 metres operation range in open field and up to 1000 metres range with TV (UHF band - channel 21-
60) simple dipole aerial installed to the receiver,
* four channel, four relay output (NO or NC) receiver,
* maximum number of transmitters: 60,
* relays output handling up to 125VAC/0,5A or 30VDC/1A,
* in-built bicolour LED for programming and status indication,
* S terminal (OC type, 1A/60V) delivering pulses to external sounder on alarm state,
* transmitter supply: 9-12 VDC / 17uA standby, 10mA active,
* receiver supply: 12 VDC ±15%, 10mA standby or 80mA with four relay action,
* operating temperature range: 0 to 40 °Celsius.
CE - This product complies with the following European Community Directives:
The Electromagnetic Compatibility Directive 89/336/EEC
The Low Voltage Directive 73/23/EEC.
The RP501 set is certified by Z.R.T.O.M. “TECHOM” (No 93/00) for security systems class “B” application.
GUARANTEE: All Elmes products carry manufacturer's standard 12 month guarantee as from date of delivery. The guarantee
is limited to replacement of faulty original parts and/or repair defects of improper manufacture. Damage, faulty use or improper
handling violets the guarantee and repair costs will be charged. In all cases, costs of delivery to and from the manufacturer of the
products to be serviced are to be paid by the customer.
Elmes Electronic 2001.
Table des matières
Autres manuels Elmes Electronic Émetteur
Manuels Émetteur populaires d'autres marques
Dejero
Dejero EnGo 3x Manuel utilisateur
Rosemount
Rosemount 4600 Manuel utilisateur
Speaka Professional
Speaka Professional 2342740 Manuel utilisateur
trubomat
trubomat GAB 1000 Manuel utilisateur
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manuel utilisateur
Rondish
Rondish UT-11 Manuel utilisateur
