Eliwell V800 Series Manuel utilisateur
V800
/P1 /P2 /P3 /P4
Driver for electronic expansion valve
Driver per valvola espansione elettronica
Controlador para válvula de expansión electrónica
EN
IT
ES
2 - ENV800
AVAILABLE MODELS, COMPONENTS & ACCESSORIES .......3-EN
COMPATIBLE VALVE LIST ................................................5-EN
MECHANICAL ASSEMBLY................................................6-EN
ELECTRICAL CONNECTIONS ..........................................7-EN
Wiring diagram description ...........................................7-EN
WIRING DIAGRAM............................................................9-EN
V800 with door open .........................10-EN
TECHNICAL DATA ...........................................................11-EN
CONDITIONS OF USE - PERMITTED USE ..................13-EN
PROHIBITED USE .............................................................13-EN
LIABILITY AND RESIDUAL RISKS .................................13-EN
USER INTERFACE .............................................................14-EN
IWK/V Keys ...........................................14-EN
LED Table ...............................................15-EN
DipSwitch Table ...................................15-EN
ACCESSING AND USING THE MENUS .......................17-EN
STATES MENU .................................................................17-EN
Setting the overheating Setpoint ....17-EN
Active alarm ..........................................17-EN
Probe display ........................................17-EN
USB COPY CARD .............................................................18-EN
USB Copy Card DipSwitch ................18-EN
USB Copy Card DipSwitch LED ........19-EN
SUPERVISION .................................................................19-EN
DipSwitch Protocol Selection...........20-EN
ALARMS ............................................................................21-EN
FUNCTIONING..................................................................24-EN
REGULATION.....................................................................25-EN
APPLICATIONS..................................................................26-EN
Stand-Alone ..........................................26-EN
Typical application ..............................26-EN
Application with multiple V800
drivers / ID985/V controllers ...........27-EN
Application with 2 V800 drivers -
1 ID985/V controller ..........................28-EN
PARAMETERS TABLE ......................................................29-EN
DISCLAIMER......................................................................33-EN
3 - EN V800
AVAILABLE MODELS, COMPONENTS & ACCESSORIES
Code Model Valve control RS485 Notes
EVD2A43BSC000 V800/P1 Imax = 300mA@230VaYes AC Output • on-board RS485
EVD2A43BXC000 V800/P2 Imax = 300mA@230VaNo AC Output
EVD2A53BSC000 V800/P3 Imax = 300mA@230VcYes DC Output • on-board RS485
EVD2A53BXC000 V800/P4 Imax = 300mA@230VcNo DC Output
Code Model Description Notes
ID34DR4SCDH00 ID985/V
Electronic controller for ventilated refrigeration units with V800 driver management via LAN
serial connection See 9MAX0017 manual
WK1400100N000 IWK/V Remote terminal for parameter conguration, I/O display, alarms etc. See 9IS60000 instructions
See User Interface
4 - ENV800
Code Model Description Notes
EVK2A43BXC010 Standard Kit
includes
1 x ID985/V
1 x V800/P2
SN8P0X3002 1 x NTC ‘FAST’
probe
TD400030 1 x ratiometric probe
EVK2A43BXC020 Starter Kit
includes
1 x ID985/V
1 x V800/P2
SN8P0X3002 1 x NTC ‘FAST’
probe
TD400030 1 x ratiometric probe
CCA0BUI02N000 1 x USB
Copy Card
DMP1000002000 1 x Device
Manager CD
1 x Device Manger interface
DMI100x002000 Device Manager
Interface USB/TTL hardware interface for use in conjunction with the Device Manager software
x=1: End User
x= 2: Service
x= 3: Manufacturer
5 - EN V800
COMPATIBLE VALVES LIST
Eliwell guarantees electrical compatibility with following PULSE valves
Brand Model Brand Model
Eliwell manufactured
by Castel PXV ALCO EX2
Danfoss AKV10 PARKER HP130
Danfoss AKV15 PARKER DS1120
Danfoss AKV20
Danfoss AKV20
Danfoss AKVA (NH3)
Note : V800 Driver delivers to the valve the same voltage as its own supply voltage
Select carefully the suitable valve coil depending on the local power distribution network
For use with different valves please contact Eliwell Technical Customer Support
MECHANICAL ASSEMBLY
The device is designed for mounting on DIN guides.
The admissible ambient temperature range for correct operation is between –10 and 55 °C.
Also avoid tting the device in places where there is high humidity and/or dirt; it is suitable for use in environ-
ments with an ordinary or normal level of pollution. Keep the area around the instrument cooling slots adequately
ventilated.
Access to dip switches and connector for USB Copy Card / IWK/V
Remove the door (see gure below right) using a slotted screwdriver or the nail of your index nger.
Congure the dip switches and/or connect the USB Copy Card or connect IWK/V.
After having made the congurations, close the front panel of the keypad by pressing it with your ngers.
ID 985/V
56.4mm
5.2mm
87mm
70.2mm
61.6mm
43.6mm
7 - EN V800
ELECTRICAL CONNECTIONS
Important! Make sure the machine is switched off before working on the electrical connections. The instru-
ment is equipped with screw-on terminal boards for connection of electrical cables with a diameter of 2.5 mm2
(one conductor only per terminal for power connections): for the capacity of the terminals, see the label on the
instrument. The relay outputs are voltage free. Do not exceed the maximum permitted current; for higher loads, use
a contactor with sufcient power capacity.
Make sure that power supply is of the correct voltage for the instrument. NTC probes have no connection polar-
ity and can be extended using a normal bipolar cable (note that if the probes are extended this inuences the
device's electromagnetic compatibility - EMC: take great care with the wiring). Probe cables, power supply cables
and serial cables should be routed separately from power cables. The pressure/ratiometric probe has a connection
polarity which must be observed.
Wiring diagram description
Terminal Label Description Notes Par. / Notes
2-3-4 RS485 Televis/Modbus serial port models /P1 /P3 only models /P1 /P3 only
6-7-8 DO1 Relay output (6= C; 7= NC; 8= NO) H21
9-10 Supply Power Supply 100...240Va (9= L; 10= N)
11-12 Valve Output Valve Output (11= VO; 12= VO) AC Valve Output models /P1 /P2
DC Valve Output models /P3 /P4
8 - ENV800
Terminal Label Description Notes Par. / Notes
14 DI1 Digital input 1 it is strictly prohibited
to connect the Digital
Input to a power source
H11, H30
15 DI2 Digital Input 2 H12, H30
16 DO2 Open Collector Output H22
17 GND Ground
18 AO1 Analogue Output repeat in 0-10V scale VO valve output (terminals 11-12)
19 AI1 Analogue Input 1 overheating probe H00 congurable NTC/4...20mA*
20 5VcProbes Power Supply **Power supply for ratiometric probe (terminal 21)
21 AI2 Analogue Input 2 saturation probe H01 congurable NTC/4...20mA*/0-5V (ratiomet-
ric)**/ LAn (remote, shared pressure transducer)
22 12VcProbes Power Supply *Power supply for 4...20mA current input (terminals 19/ 21)
23-24 LAN Powered serial port ID985/V connection
DMI/CC Serial port for connection to
• USB Copy Card / • IWK/V See DipSwitch
TTL Serial port for connection
to Televis / Modbus PtS, dEA, FAA, PtY, Ptb
9 - EN V800
DO1
V800
NONC
CVOVO
N
L
RS-485
/P1 /P3 Models
only
Supply
100...240Vac
Televis/
Modbus
(use BusAdapter)
Televis/
Modbus
(direct connection)
7 8
9 10 11 12
6
19 20 21 22 23 2418
-+
G
3 42
5VcAI1
AO1 GNDLAN
12Vc
AI2
15 16 1714
DO2DI2
DI1 GND
Valve Output
AC output /P1 /P2
DC output /P3 /P4
Check carefully
ON
12
ON
34
ON
56
ON
78
ON
910
DMI/CC
Keyb
A
B
C
20 21 22 23 24
12Vc
AI2
I
SIG +
20 21 22 23 24
5VcGND
AI2
V
SIG + -
NTC
4...20mA
ratiometric
0-5V
19 20 21 22 23 24
AI1 GND
AI2
15 16 1714
DI2
default configuration
DI1 GND
19 20 21 2218
12Vc
16 17
DO2
Open Collector
LOAD
max 35mA
I
SIG +
‘Stand-Alone’ mode alone
repeats
Valve Output
scale 0-10V
WIRING DIAGRAM
10 - ENV800
ON
12
ON
34
ON
56
ON
78
ON
910
TTL
A
B
CTTL
IWK/V rear
Supply from V800
1 2 3 4 5 6 7 8 9
+
14 15 16 17 18 19 20
A B C D
LAN
SUPPLY
100...240Va 2.5W max
TTL
LAN
GND
+-
-
12 13
ID985/V
+-
set
f nc
IWK/V
%T1 T2 ∆T
DO1
V800
NONC
CVOVO
N
L
RS-485
/P1 /P3 Models
only
Supply
7 8
9 10 11 12
6
19 20 21 22 23 2418
-+
G
3 42
5VcAI1
AO1 GNDLAN
12Vc
AI2
15 16 1714
DO2DI2
DI1 GND
Valve Output
ON
12
ON
34
ON
56
ON
78
ON
910
Keyb
A
B
C
CIRCUIT DIAGRAM - V800 with open door
USB Copy Card connection
• Display DipSwitch and use of DMI/CC
connector for USB/Copy Card
IWK/V / LAN connection
• Display DipSwitch and use of Keyb connector for IWK/V.
• Display LAN connection with ID985/V
Ce manuel convient aux modèles suivants
4
Table des matières
Langues :
Autres manuels Eliwell Entraînement CC
Manuels Entraînement CC populaires d'autres marques
Vincent Associates
Vincent Associates UNIBLITZ ED12DSS Manuel utilisateur
EKSMA OPTICS
EKSMA OPTICS DQ-100-4 Manuel de la liste des pièces
Chamberlain Garog
Chamberlain Garog D Series Manuel utilisateur
Parker
Parker PDS Series Manuel utilisateur
Festo
Festo DGC G Series Guide de configuration
Binks
Binks QS-5012-1-CE Manuel utilisateur
