Elite Screens VMAX2 (Plus) Series Mode d’emploi

Updated 3/22/2017 1 www.elitescreens.com

Tubular Motor Replacement Instructions

for VMAX2 models 135” and above / Spectrum models 135” and above

For technical support or further assistance, call 877-511-1211 x604

ATTENTION:

Elite Screens does not recommend making unnecessary adjustments to the screen, as improper

adjustments will damage the unit and void your warranty.

1. Remove the screws on the motor bracket and left end cap (facing the screen) with a Phillips

screwdriver, then remove the end cap.

2. After removing the end cap, carefully remove the decorative sheet by pulling it outward towards

the open end.

Decorative sheet

Decorative sheet removed

End cap

screws

Motor bracket

screws

Updated 3/22/2017 2 www.elitescreens.com

3. Remove the power cord and 3P cable, shown in the image below.

4. Using the screwdriver, at the right side end cap, push the roller out to expose the roller on the

open left side end of the housing. Being sure not to snag or scratch the material on the housing, lift

and pull the roller out from the left side enough to access the ground terminal.

5. Cut off the ground terminal and remove the motor.

Screwdriver pushing out

roller from right side

Ground

Terminal

Power cord

Ground Terminal

removed

Motor

Housing

Roller

Updated 3/22/2017 3 www.elitescreens.com

6. Separate the motor from the motor bracket and attach the same bracket to the new motor.

7. Install the new motor. Be sure to align the drive wheel with the ladder on the roller.

8. Place the bracket into the housing where the RJ45 port on the circuit board lines up with the hole

on the housing.

9. Two people are suggested for this step. While one person keeps hold of the left side, the other

will need to loop thin rope or twine around the motor cap on the right side of the roller. (This will help

guide the roller back into the housing and reconnect with the shock absorber core.) Push in the left

side end cap back into the housing while carefully guiding the right end of the roller into place.

Roller

Motor

RJ45 port

Remove the

motor bracket

from here

Updated 3/22/2017 4 www.elitescreens.com

10. After inserting the motor into the housing, insert the power cord and the 3P cable into the circuit

board. Then connect the power cable to the ground of the motor cable and clamp it with the ground

terminal.

11. Affix the ground terminal to the bracket and housing with screws removed in step 1.

Shock absorber core

Motor cap

Rope or

twine

Power cord

Power cable/Motor cable

Power cable/Motor cable clamped with ground terminal

Ground terminal

Updated 3/22/2017 5 www.elitescreens.com

12. Replace the decorative sheet removed in step 2.

13. Replace and secure the end cap with screws removed in step 1.

NOTE: After replacing the tubular motor, you may need to adjust the limit switch to drop the screen at

your preferred height.

For a local Elite Screens contact or Technical Support, please visit

www.elitescreens.com

Finished assembly.

Autres manuels pour VMAX2 (Plus) Series

Table des matières

Autres manuels Elite Screens Écran de projection

Elite Screens

Elite Screens TE100HC2 Manuel utilisateur

Elite Screens

Elite Screens Evanesce B Series Guide de référence rapide

Elite Screens

Elite Screens QuickStand Series Manuel utilisateur

Elite Screens

Elite Screens AEON series Manuel utilisateur

Elite Screens

Elite Screens F100NWH Manuel du propriétaire

Elite Screens

Elite Screens Kestrel Series Manuel utilisateur

Elite Screens

Elite Screens Electric84H Manuel utilisateur

Elite Screens

Elite Screens TE100HC3 Manuel du propriétaire

Elite Screens

Elite Screens F60XWV1 Manuel utilisateur

Elite Screens

Elite Screens VMAX PLUS 4 SERIES Manuel utilisateur

Elite Screens

Elite Screens Insta-DEM Screen Series Manuel utilisateur

Elite Screens

Elite Screens Spectrum Tension Series Manuel utilisateur

Elite Screens

Elite Screens Raptor Series Manuel utilisateur

Elite Screens

Elite Screens ezFrame CineGrey 5D Manuel utilisateur

Elite Screens

Elite Screens Spectrum Tab-Tension Series Manuel utilisateur

Elite Screens

Elite Screens IWB85SW2a Manuel utilisateur

Elite Screens

Elite Screens Evanesce B Series Mode d’emploi

Elite Screens

Elite Screens Yard Master Electric Mode d’emploi

Elite Screens

Elite Screens WhiteBoardScreen Series Manuel utilisateur

Elite Screens

Elite Screens Elite Silvermax Series Manuel utilisateur

Elite Screens

Elite Screens Home100IWH2-A Manuel utilisateur

Elite Screens

Elite Screens Home100IWH3 Manuel utilisateur

Elite Screens

Elite Screens ezFrame R180WH1 Manuel utilisateur

Elite Screens

Elite Screens TE100HC2 Manuel utilisateur

Manuels Écran de projection populaires d'autres marques

FART PRODUKT

FART PRODUKT Standard SCREEN Manuel utilisateur

Draper

Draper E Series Manuel

Laarhoven

Laarhoven Companion II Manuel utilisateur

Renogy

Renogy RMS-LFPS-US Manuel utilisateur

Da-Lite

Da-Lite ExecutiveElectrol Manuel utilisateur

Samsung

Samsung S*H65* Manuel utilisateur

FONESTAR

FONESTAR PPTR-43100-FA Manuel utilisateur

Slide Clear

Slide Clear Varro XL Manuel utilisateur

OS РХ-090Н Manuel utilisateur

Niko

Niko 10-845 Manuel utilisateur

Speaka Professional

Speaka Professional 2357532 Manuel d'utilisation

Sima

Sima XL-72 Manuel utilisateur

Jasic

Jasic EVO 2.0 ET-200P Manuel utilisateur

InFocus

InFocus SC-WALL GRY-92H Manuel

Barco

Barco OverView MVL-615 Manuel utilisateur

Draper

Draper Envoy Manuel

SI Dynamic 2 XL Manuel utilisateur

Draper

Draper Nocturne+ E Instructions d'installation