Elcometer 204 Manuel utilisateur

English

Elcometer 204

Steel Ultrasonic Thickness Gauge

Operating Instructions

English

The Elcometer 204 Steel Ultrasonic Thickness Gauge has been tested in accordance with EU

regulations governing Electro-magnetic compliance and it meets the required directives.

is a registered trademark of Elcometer Limited.

All other trademarks acknowledged.

system or otherwise) or translated into any language, in any form or by any means (electronic, mechanical,

magnetic, optical, manual or otherwise) without the prior written permission of Elcometer Limited.

A copy of this Instruction Manual is available for download on our Website via www.elcometer.com/

downloads.

Doc.No. TMA-0410 Issue 03

Text with Cover No: 20018

CONTENTS

Section Page

1 About your gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2 Getting started. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3 Taking a reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4 Probe Zero . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

5 Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

6 Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

7 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

8 Related equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

9 Technical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

10 Spares . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

11 Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

12 Transducers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

13 Condition and preparation of surfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

14 Application notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Thank you for purchasing this Elcometer 204 Steel Ultrasonic Thickness Gauge. Welcome to Elcometer.

Elcometer are world leaders in the design, manufacture and supply of coatings inspection equipment. Our

products cover all aspects of coating inspection, from development through application to post application

inspection.

The Elcometer 204 Steel Ultrasonic Thickness Gauge is a world beating product. With the purchase of this

gauge you now have access to the worldwide service and support network of Elcometer. For more

information visit our website at www.elcometer.com.

1 ABOUT YOUR GAUGE

The Elcometer 204 Steel Ultrasonic Thickness Gauge is a handheld gauge for fast and accurate

measurement of the thickness of steel.

Your gauge is capable of measuring the thickness of material such as steel plate with accuracy as high as

± 0.01 mm (± 0.001"). The principal advantage of ultrasonic measurement over traditional methods is that

ultrasonic measurements can be performed with access to only one side of the material being measured.

1.1 WHAT THIS BOX CONTAINS

• Elcometer 204 Steel Ultrasonic Thickness Gauge

• Transducer

• Bottle of couplant

• Battery, 2 x

• Carrying case

• Operating instructions

Your gauge is packed in a cardboard and foam package. Please ensure that this packaging is disposed of

in an environmentally sensitive manner. Please consult your Local Environmental Authority for further

guidance.

To maximise the benefits of your new Elcometer Ultrasonic Thickness Gauge, please take some

time to read these Operating Instructions. Do not hesitate to contact Elcometer or your Elcometer

supplier if you have any questions.

1.2 STANDARDS

The Elcometer 204 Steel Ultrasonic Thickness Gauge can be used in accordance with the following

National and International Standards ASTM E 797, EN 15317.

2 GETTING STARTED

2.1 FITTING BATTERIES

Your gauge may be used with dry cell batteries or rechargeable batteries.

2 x LR6 (AA) alkaline batteries are supplied in the kit.

To fit or replace batteries:

1. Locate battery compartment cover at top of gauge.

2. Unscrew battery compartment cover.

3. Referring to battery polarity instructions on rear of gauge, insert

batteries into gauge ensuring correct polarity.

4. Replace battery compartment cover.

Remove the batteries from the gauge if it is to remain unused for a long

period of time. This will prevent damage to the gauge in the event of

malfunction of the batteries.

When the battery voltage is low the entire display will start to flash. When

this occurs the batteries should be replaced.

Note: Alkaline batteries must be disposed of carefully to avoid

environmental contamination. Please consult your local environmental

authority for information on disposal in your region.

Do not dispose of any batteries in fire.

Note: An interface is located on the bottom of your gauge. This interface is used to program the gauge at

the factory and has no function for users of the gauge.

Elcometer 204

Steel Ultrasonic

Thickness Gauge

PRB

OFF

Battery

compartment

cover

2.2 THE TRANSDUCER

The transducer transmits and receives the ultrasonic energy or

sound waves that the gauge uses to determine the thickness of

the material being measured.

The transducer connects to the gauge via the attached cable,

and two coaxial connectors. The orientation of the dual coaxial

connectors is not critical; either plug may be fitted to either

socket.

The transducer must be used correctly in order for the gauge to

produce accurate, reliable measurements.

The diagram shows the two semicircles of the wearface and the

barrier separating them. One of the semicircles transmits

ultrasonic sound into the material being measured, and the other

semicircle receives the sound echoes back into the transducer.

When the transducer is placed against the material being

measured, it is the area directly beneath the centre of the

wearface that is being measured.

Wearface

2.3 THE KEYPAD

Key Functions

Press to switch the gauge on or off.

When switching off, the gauge retains all of its settings.

If the gauge is idle for 5 minutes, it will switch itself off.

Press to change units (metric/imperial)

Switches the display backlight between three settings; on, off and auto.

• ON - backlight is on

• OFF - backlight is off

• AUTO - backlight automatically illuminates while the gauge is making a measurement and switches

off after several seconds (to conserve battery life).

Press to zero the gauge - see “Probe Zero” on page 10.

OFF

PRB

2.4 THE DISPLAY

INMM/ s

Stability indicator

• One bar - no readings

are being taken

• Less than 5 bars -

reading is unstable and

may be inaccurate

• More than 5 bars -

reading is stable

(Refer to “Read display” on

page 9 and “Transducers” on

page 16 for information on

how to achieve a stable

measurement).

Units (IN, MM, IN/µs, MM/s)

Thickness value/Text

3 TAKING A READING

Disclaimer: Inherent in ultrasonic thickness measurement is the possibility that the instrument will use the

second echo rather than the first echo from the back surface of the material being measured. This may

result in a thickness reading which is TWICE what it should be.

The responsibility for proper use of the instrument and recognition of these types of phenomenon rests

solely with the user of the instrument.

3.1 BEFORE YOU START

•Prepare the surface. . . . . . . . . . . . . . See “Condition and preparation of surfaces” on page 17.

•Zero the gauge.. . . . . . . . . . . . . . . . . See “Probe Zero” on page 10.

3.2 PROCEDURE

1. Apply couplant

For the gauge to work correctly there must be no air gaps between the transducer and the surface of

the material to be measured. This is achieved using a material called a couplant.

Before the transducer is placed on the surface, put a small amount of the couplant supplied with the

gauge on the surface of the material. Typically a single drop is sufficient.

2. Place transducer onto surface of material to be measured

Press the transducer into the couplant. Moderate pressure on the top of the transducer using the

thumb or index finger is sufficient; it is only necessary to keep the transducer stationary and the

surface seated flat against the surface of the material.

Autres manuels pour 204

Table des matières

Autres manuels Elcometer Instrument de mesure

Elcometer

Elcometer Zahn 2210 Manuel utilisateur

Elcometer

Elcometer 3505 Manuel utilisateur

Elcometer

Elcometer CG100ABDL Manuel utilisateur

Elcometer

Elcometer 308 Manuel utilisateur

Elcometer

Elcometer 124 Manuel utilisateur

Elcometer

Elcometer 456 Manuel utilisateur

Elcometer

Elcometer 415 Manuel utilisateur

Elcometer

Elcometer 456 IPC Manuel utilisateur

Elcometer

Elcometer 311 Manuel utilisateur

Elcometer

Elcometer 331 H Manuel utilisateur

Elcometer

Elcometer 205 Manuel utilisateur

Elcometer

Elcometer 224 Manuel utilisateur

Elcometer

Elcometer 407L Manuel utilisateur

Elcometer

Elcometer 456 Manuel utilisateur

Elcometer

Elcometer SG80 Manuel utilisateur

Elcometer

Elcometer 138 Manuel utilisateur

Elcometer

Elcometer 119 Manuel utilisateur

Elcometer

Elcometer Novo-Gloss 402 Manuel utilisateur

Elcometer

Elcometer 456 Manuel utilisateur

Elcometer

Elcometer 319/2 Manuel utilisateur

Elcometer

Elcometer Novo-Gloss 401 Manuel utilisateur

Elcometer

Elcometer 224 Manuel utilisateur

Elcometer

Elcometer CG60DL Manuel utilisateur

Elcometer

Elcometer 331 Series Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur