Ekwb EK-Vector RTX 2080 Backplate Mode d’emploi

All disclosures, notices and warranty conditions are being written on the back of the box.

Installation and mounting manual for EK-Vector RTX 2080 Backplate

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates. Before

installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

STEP 1: GENERAL INFORMATION. Sample picture of NVIDIA GeForce RTX 2080 graphics card.

STEP 2: PREPARING YOUR GRAPHICS CARD

EK-Vector RTX 2080 is very easy to install. First install EK-Vector RTX 2080 series water block according to its installation manual. If you have it already

installed, please check the picture below to see which mounting screws are to be left in their position and which are to be removed. Please remove the six

(6) M2.5x4 AX1 screws and their PVC washers as well (marked with arrow).

STEP 3: APPLYING THE THERMAL PADS

EK-Vector RTX 2080 features passive cooling of the printed circuit board and its components therefore it is mandatory to install the enclosed

thermal pads. Please install enclosed 1,5mm thick thermal pad (Thermal Pad F –1,5mm (120x16)) and Thermal Pad F –1,0mm (120x16)) as

shown on the picture below. You may need to trim the excess thermal pad.

Thermal Pad F 1.5mm

Thermal Pad F 1.0mm

All disclosures, notices and warranty conditions are being written on the back of the box.

STEP 4: ATTACHING EK-Vector RTX 2080 TO THE GRAPHICS CARD

Take enclosed mounting screws and install them as shown on picture below. Use six (6) M2.5x7 AX1 screws, and tighten them using Philips head screwdriver.

HINT: Do not tighten screws until they are all positioned in their mounting holes. The backplate has milled in standoffs, so there is no fear of over tightening of

the screws. Nevertheless do not exaggerate with screwing force as there is no need for it.

By all means users must also consider that this product is intended to be used only with EK-Vector RTX 2080 series water blocks. No other 3rd party heat sinks

or coolers are officially supported! EK does not offer any assistance or support in the latter application.

IMPORTANT DISCLOSURES

VERY IMPORTANT NOTICE: Once the installation is completed, it is a recommended practice to test the cooling circuit for leaks prior to powering up the

computer. We recommend a 24 hour leak test prior to powering up the computer. Do not test the water block using city water pressure. This will rupture the top

of the housing and render the block unusable (and will void your warranty).While all efforts have been made to provide the most comprehensive tutorial possible,

EK Water Blocks assumes no liability expressed or implied for any consequential damage(s) occurring to your equipment as a result of using EK Water Blocks

cooling products, either due to errors or omissions on our part in the above instructions, or due to failure or defect in the EK Water Blocks cooling products.

WARRANTY:

Our products are warranted against defects in materials or workmanship for a period of 24 months beginning from the date of delivery to the final user. During

this period, products will be repaired or have parts replaced at our discretion provided that: (I) the product is returned to the agent from whom it was purchased;

(II) the product has been purchased by an end user and has not used for commercial purposes; (III) the product has not been misused, handled carelessly, or

used in a manner other than in accordance with the instructions provided describing its installation and proper use. This warranty does not confer rights other

than those expressly set out above and does not cover any claims for consequential loss or damage. This warranty is offered as an extra benefit and does not

affect your statutory rights as a consumer. This warranty is voided if the product comes in contact with aggressive UV additives or other improper liquids.

EK blocks are sealed with warranty void circular label, which proves that the block has withstood a pressure leak test. Removing it will void leak-free guarantee

and not the guarantee on the product itself. Any other RMA issues can be reported to EK Support at http://www.ekwb.com/support for further analysis.

REQUIRED TOOLS AND MOUNTING SCREWS:

Philips head screwdriver scissors

M2.5x7 AX1

Table des matières

Autres manuels ekwb Matériel informatique

ekwb

ekwb EK-FC 6970 Manuel

ekwb

ekwb EK-Quantum Vector FE RTX 3080 Manuel utilisateur

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Manuel utilisateur

ekwb

ekwb EK-Quantum Vector FE RTX 3090... Manuel utilisateur

ekwb

ekwb EK-FB KIT GA P67A UD7 Manuel

ekwb

ekwb EK-FC780 GTX Ti Manuel

ekwb

ekwb EK-FC1080 GTX Ti FTW3 Manuel utilisateur

ekwb

ekwb 115 Series Manuel utilisateur

ekwb

ekwb EK-Vector Trio RTX 2080 Ti Manuel utilisateur

ekwb

ekwb EK-Velocity sTR4 Manuel utilisateur

ekwb

ekwb EK-FB ASUS R5-E10 Mode d’emploi

ekwb

ekwb EK-FC Radeon Vega Strix Backplate Manuel

ekwb

ekwb EK-FC980 GTX Classy Manuel

ekwb

ekwb EK-Classic 115 D-RGB Series Manuel utilisateur

ekwb

ekwb EK-Pro RTX A5500 Rack - Ni+Inox Manuel utilisateur

ekwb

ekwb EK-Quantum Vector FTW3 RTX 3070 Manuel utilisateur

ekwb

ekwb Supremacy MX AMD Manuel utilisateur

ekwb

ekwb R9-290X Series Mode d’emploi

ekwb

ekwb EK-D5 Dual TOP Mode d’emploi

ekwb

ekwb EK-Quantum Convection M.2 NVMe Manuel utilisateur

ekwb

ekwb EK-FC1080 GTX G1 Manuel utilisateur

ekwb

ekwb EK-Supreme HF Mode d’emploi

ekwb

ekwb EK-FC470 GTX Manuel

ekwb

ekwb EK-Pro GPU WB RTX 4000 - Ni + Inox Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur

ekwb EK-Vector RTX 2080 Backplate Mode d’emploi

Manuels Matériel informatique populaires d'autres marques