Ekwb EK-FC980 GTX Mode d’emploi

All disclosures, notices and warranty conditions are being written on the back of the box. Revision 1.1. Released on 24th of January, 2015.

Installation and mounting manual for EK-FC980 GTX

Backplate

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates. Before

installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

STEP 1: GENERAL INFORMATION. Sample picture of nVidia GeForce 980 GTX graphics card.

STEP 2: PREPARING YOUR GRAPHICS CARD

EK-FC980 GTX Backplate is very easy to install. First install EK-FC980 GTX series water block according to its installation manual. If you have it

already installed, please check the picture below to see which mounting screws are to be left in their position and which are to be removed. Screws

with marked with red arrow need to be remove and replace with four (4) M2.5x4 DIN7985. Please remove the seven (7) screws marked with white

arrow screws.

STEP 3: APPLYING THE THERMAL PADS

EK-FC980 GTX Backplate features passive cooling of the printed circuit board and its components therefore it is mandatory to install the enclosed

thermal pad. Please install enclosed 1mm thick thermal pad (Thermal Pad A –1,0mm (100x16)) as shown on the picture below. You may need to

trim the excess thermal pad. Trim 1mm Thermal Pad to fit hole.

Thermal PAD A 1,0mm

EK-FC980 GTX

Backplate

M2.5x4 DIN 7991 screw

PVC WASHER

All disclosures, notices and warranty conditions are being written on the back of the box. Revision 1.1. Released on 24th of January, 2015.

STEP 4: ATTACHING EK-FC980 GTX BACKPLATE TO THE GRAPHICS CARD

Take enclosed mounting screws and install them as shown on picture below (some screws are in block mounting). EKWB recommends users to start

with six (6) M2.5x6 DIN 7985 (HINT: do not tighten screws until they are all positioned in their mounting holes) in the middle of the card and then

continue outwards. The backplate has milled in standoffs, so there is no fear of over tightening of the screws. Nevertheless do not exaggerate with

screwing force as there is no need for it.

(By all means users must also consider that this product is intended to be used only with EK-FC980 GTX series wat er blocks. No other 3rd party

heat sinks or coolers are supported!)

EKWB short top versions: ACETAL, CSQ TOP-s:

IMPORTANT DISCLOSURES

VERY IMPORTANT NOTICE: Once the installation is completed, it is a recommended practice to test the cooling circuit for leaks prior to powering up the

computer. We recommend a 24 hour leak test prior to powering up the computer. Do not test the water block using city water pressure. This will rupture the top

of the housing and render the block unusable (and will void your warranty).While all efforts have been made to provide the most comprehensive tutorial possible,

EK Water Blocks assumes no liability expressed or implied for any consequential damage(s) occurring to your equipment as a result of using EK Water Blocks

cooling products, either due to errors or omissions on our part in the above instructions, or due to failure or defect in the EK Water Blocks cooling products.

WARRANTY:

Our products are warranted against defects in materials or workmanship for a period of 24 months beginning from the date of delivery to the final user. During

this period, products will be repaired or have parts replaced at our discretion provided that: (I) the product is returned to the agent from whom it was

purchased; (II) the product has been purchased by an end user and has not used for commercial purposes; (III) the product has not been misused, handled

carelessly, or used in a manner other than in accordance with the instructions provided describing its installation and proper use. This warranty does not confer

rights other than those expressly set out above and does not cover any claims for consequential loss or damage. This warranty is offered as an extra benefit and

does not affect your statutory rights as a consumer. This warranty is voided if the product comes in contact with aggressive UV additives or other improper

liquids.

EK blocks are sealed with warranty void circular label, which proves that the block has withstood a pressure leak test. Removing it will void leak-free guarantee

and not the guarantee on the product itself. Any other RMA issues can be reported to EK Support at http://www.ekwb.com/support for further analysis.

REQUIRED TOOLS AND MOUNTING SCREWS:

Philips head screwdriver scissors

M2.5X6 DIN 7985 screw

M2.5x8 DIN 7985 screw

PVC WASHER

M2.5 NUT

Table des matières

Autres manuels ekwb Matériel informatique

ekwb

ekwb EK-FB ASUS M6I Mode d’emploi

ekwb

ekwb EK-Vector FTW3 RTX 2080 Ti Manuel utilisateur

ekwb

ekwb EK-FC R9-390X TF5 Mode d’emploi

ekwb

ekwb EK-FB ASUS R5-E10 Mode d’emploi

ekwb

ekwb EK-FC780 GTX HOF Series Manuel

ekwb

ekwb Classic D-RGB S240 Manuel utilisateur

ekwb

ekwb GTX 1080 Ti Aorus Backplate Mode d’emploi

ekwb

ekwb EK-FC WX9100 PRO BACKPLATE Manuel utilisateur

ekwb

ekwb EK X Series Manuel utilisateur

ekwb

ekwb EK-Supreme HF Mode d’emploi

ekwb

ekwb EK-PRO GPU WB RTX A100 80GB Manuel utilisateur

ekwb

ekwb EK-FC980 GTX Ti TF5 Series Manuel

ekwb

ekwb EK-FB ASUS M6E Mode d’emploi

ekwb

ekwb EK-Quantum Reflection2 PC-O11D EVO D5 PWM... Manuel utilisateur

ekwb

ekwb EK-FB ASUS X58 Mode d’emploi

ekwb

ekwb EK-FC 780 GTX DCII Series Manuel

ekwb

ekwb EK-FC 4890 VAPOR X Mode d’emploi

ekwb

ekwb EK-FC780 GTX Ti Matrix Manuel

ekwb

ekwb EK-Quantum Kinetic FLT D5/DDC Body D-RGB Manuel utilisateur

ekwb

ekwb EK-Nucleus AIO CR360 Vision D-RGB Manuel utilisateur

ekwb

ekwb EK-Quantum RX 6800 Manuel utilisateur

ekwb

ekwb 3831109816202 Mode d’emploi

ekwb

ekwb EK-Quantum Momentum Aorus Z490 Master D-RGB Manuel utilisateur

ekwb

ekwb EK-XRES DCP 4.0 Manuel

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur

ekwb EK-FC980 GTX Mode d’emploi

Manuels Matériel informatique populaires d'autres marques