Ekwb EK-Annihilator Pro ILM Series Manuel utilisateur

All disclosures, notices and warranty conditions are being written on EKWB website. Revision 1. Released on 5th of Merch 2019

EK-Annihilator Pro ILM series CPU water block installation manual

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates. Before installation

of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

1. Please carefully read the manual before through before beginning with the installation process!

2. Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).

3. The EK-HFB, EK-HDC and EK-ACF type fittings require only a small amount of force to screw them firmly in place as the liquid seal is ensured by the rubber o-ring gaskets.

4. The use of corrosion inhibiting coolants is always recommended for any liquid cooling system.

STEP 1: GENERAL INFORMATION ON PRODUCT COMPATIBILITY

STEP 2: TABLE OF CONTENT

STEP 3: ANNIHILATOR INLET AND OUTLET PORTS

Congratulations on your purchase of EK-Annihilator Pro ILM water

block. This water block is pre-assembled for use with modern Intel®

Processors with LGA 3647 socket for server and workstation type

motherboards.

This water block supports the LGA 3647 socket.

Plug G1/8

M3x18

Mounting plate

O-Ring

Jet Plate

Copper Base

Top

Plug G1/4

STEP 3a: G1/8 ports configuration:

6 ports G1/8 are available for low profile server cooling solution. Center ports are INLET ports, any of other four can be used as OUTLET port. Make sure, that

other non used ports G1/4 and G1/8 plugs are in place, tightened firmly.

Inlet

outlet

STEP 3b: G1/4 ports configuration:

3 ports G1/4 are available for normal use of water block for workstations. Center port is INLET other two can be used as OUTLETS. Make sure that all other

non used port plugs G1/8 and G 1/4 are in place, tightened firmly.

outlet

Inlet

outlet

All disclosures, notices and warranty conditions are being written on EKWB website. Revision 1. Released on 5th of Merch 2019

STEP 4: PREPARING CPU AND APPLYING THERMAL GREASE (TIM)

STEP 5: INSTALLING THE WATER BLOCK

STEP 6: CONNECTING THE WATER BLOCK TO THE COOLING LOOP

Cleaning the CPU: Wipe the CPU’s contact surface (by using non–

abrasive cloth or

Q-tip

Applying thermal compound: EK recommends a blob or line method

of applying the enclosed EK-TIM Ectotherm™ thermal compound to the

CPU heatspreader (IHS) - see sample photo on right. The quantity of

about pea size is just about right. There is no need to cover the whole

IHS. Applying too much thermal grease will have negative impact on the

cooling performance!

1) On majority of motherboards the EK-Annihilator Pro ILM can be

sucessfully installed with motherboard already being pre-fitted to the

computer chassis. Still, it is best practice to place a motherboard on an

even surface with front side facing up.

2) Install CPU and apply TIM (thermal grease) as shown in STEP 5

3) Align water block above the LGA 3647 socket on motherboard with

pre-installed CPU.

4) Tighten the screws using 4mm Allen Key the cross pattern.

5a: Tightening sequence:

You have to tighten the screws in cross pattern sequence using 4mm

Allen Key. Screws 1 and 2 must be tightened until they hit the limiter

and are not able to turn more.

Do not overtighten the screws 3 and 4!

Step 6a: Connecting G1/8 fittings with tube:

Carefully identify the direction of the flow in your circuit. EK recommends the

use of EK-HFB Fitting 6mm G1/8 and EK-Tube ZMT 6/9mm Matte Black tubing.

1. Install Barb 1/8 [1] to the CPU block by using 3/16 Allen Key.

2. Mount Clamp [3] to the tubing [2]

3. Mount the tube [2] to the barb [1]

Step 6b: Connecting G1/4 fittings with tube:

Carefully identify the direction of the flow in your circuit. EK recommends the

use of EK-HFB 10 mm barb fittings and EK-Tube ZMT 10/16mm.

The use of biocide containing and corrosion inhibiting coolant is always

recommended for any liquid cooling system. EK recommends using EK-CryoFuel.

Ce manuel convient aux modèles suivants

Autres manuels ekwb Matériel informatique

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Manuel utilisateur

ekwb

ekwb EK-Vector FTW3 RTX 2080 Ti Mode d’emploi

ekwb

ekwb 3831109816202 Mode d’emploi

ekwb

ekwb EK-FB ASUS M8E Monoblock Series Manuel utilisateur

ekwb

ekwb EK-Quantum Reflection2 PC-O11D EVO D5 PWM... Manuel utilisateur

ekwb

ekwb EK-FB KIT GA Z97X-SOC Force Mode d’emploi

ekwb

ekwb EK-FC1080 GTX G1 Manuel utilisateur

ekwb

ekwb EK-Quantum Vector Aorus RTX 2080 Ti Manuel utilisateur

ekwb

ekwb EK-FC Fury X Manuel

ekwb

ekwb EK-AIO 120 D-RGB Manuel utilisateur

ekwb

ekwb EK-FC 6970 Manuel

ekwb

ekwb EK-FC970 GTX TF5 Manuel

ekwb

ekwb EK-FC980 Manuel

ekwb

ekwb EK-FC Strix RTX 2080 Ti Backplate Classic Manuel utilisateur

ekwb

ekwb EK-FC680 GTX FTW Mode d’emploi

ekwb

ekwb EK-FC780 GTX Jetstream Manuel

ekwb

ekwb EK-FC780 GTX Ti Series Manuel utilisateur

ekwb

ekwb EK-FB ASUS R5-E10 Mode d’emploi

ekwb

ekwb EK-Dual DDC X-Top CSQ Manuel

ekwb

ekwb EK-FC780 GTX Classy Rev.2.0 Backplate Mode d’emploi

ekwb

ekwb EK-Quantum Convection M.2 NVMe Manuel utilisateur

ekwb

ekwb EK-FB ASUS C6H Monoblock Manuel utilisateur

ekwb

ekwb EK-FC R9 Nano Series Manuel

ekwb

ekwb GTX 1080 Ti Aorus Backplate Mode d’emploi

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur

ekwb EK-Annihilator Pro ILM Series Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques