Eaton Powerware 9355 Parallel Manuel utilisateur
Powerware 9355 Parallel UPS
10/15 kVA
User’s Guide
®
Class A EMC Statements
FCC Part 15
NOTE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
ICES-003
This Class A Interference Causing Equipment meets all requirements of the Canadian Interference Causing
Equipment Regulations ICES-003.
Cet appareil numérique de la classe A respecte toutes les exigences du Reglement sur le matériel brouilleur du
Canada.
IEC 62040-2
Some configurations are classified under IEC 62040-2 as “Class-A UPS for Unrestricted Sales Distribution.” For
these configurations, the following applies:
WARNING This is a Class A-UPS Product. In a domestic environment, this product may cause radio interference, in
which case, the user may be required to take additional measures.
Powerware, ABM, and Powerware Hot Sync are registered trademarks and X-Slot and LanSafe are trademarks of
Eaton Power Quality Corporation.
Greenlee is a registered trademark of Greenlee Textron.
ECopyright 2005 Eaton Corporation, Raleigh, NC, USA. All rights reserved. No part of this document may be
reproduced in any way without the express written approval of Eaton Corporation.
Requesting a Declaration of Conformity
Units that are labeled with a CE mark comply with the following harmonized standards and EU directives:
SHarmonized Standards: IEC 62040-1-1 and IEC 62040-2; IEC 60950 Third Edition
SEU Directives: 73/23/EEC, Council Directive on equipment designed for use within certain voltage limits
93/68/EEC, Amending Directive 73/23/EEC
89/336/EEC, Council Directive relating to electromagnetic compatibility
92/31/EEC, Amending Directive 89/336/EEC relating to EMC
The EC Declaration of Conformity is available upon request for products with a CE mark. For copies of the EC
Declaration of Conformity, contact:
Eaton Power Quality Oy
Koskelontie 13
FIN-02920 Espoo
Finland
Phone: +358-9-452 661
Fax: +358-9-452 665 68
Special Symbols
The following are examples of symbols used on the UPS or accessories to alert you to important
information:
RISK OF ELECTRIC SHOCK - Indicates that a risk of electric shock is present and the
associated warning should be observed.
CAUTION: REFER TO OPERATOR’S MANUAL - Refer to your operator’s manual for
additional information, such as important operating and maintenance
instructions.
This symbol indicates that you should not discard the UPS or the UPS batteries
in the trash. This product contains sealed, lead-acid batteries and must be
disposed of properly. For more information, contact your local recycling/reuse or
hazardous waste center.
This symbol indicates that you should not discard waste electrical or electronic
equipment (WEEE) in the trash. For proper disposal, contact your local
recycling/reuse or hazardous waste center.
ON - Indicates that the switch is in the ON position.
OFF - Indicates that the switch is in the OFF position.
PHASE - The word “phase.”
EATON Powerware®9355 Parallel UPS (10/15 kVA) User’s Guide S164201601 Rev A www.powerware.com i
Table of Contents
1 Introduction 1.........................................................
2 Safety Warnings 3.....................................................
3 UPS Setup 7..........................................................
Inspecting the Equipment 7................................................................
Floor Loading 8........................................................................
Clearances 8..........................................................................
Unloading the Cabinet(s) 9................................................................
Three-High Cabinets or Two-High EBMs 9...................................................
Two-High UPS Cabinets 13..............................................................
4 Parallel Installation 17...................................................
5 Installing Options 27....................................................
Powerware Hot Sync CAN Bridge Card 28......................................................
6 Stabilizing the Cabinet 33................................................
7 Extended Battery Module Installation 37.....................................
8 Operation 41...........................................................
Control Panel Functions 41.................................................................
Changing the Language 42..............................................................
Display Functions 42...................................................................
User Settings 44......................................................................
Initial Startup 46........................................................................
Configuring the UPS for EBMs 47............................................................
Parallel System Shutdown 48...............................................................
Individual UPS Shutdown 49................................................................
Restarting the Parallel System 50............................................................
9 Parallel Bypass 51......................................................
10 Troubleshooting 53......................................................
Typical Alarms and Conditions 53............................................................
Silencing the Alarm 55....................................................................
Service and Support 56...................................................................
TABLE OF CONTENTS
EATON Powerware®9355 Parallel UPS (10/15 kVA) User’s Guide S164201601 Rev A www.powerware.com
ii
EATON Powerware®9355 Parallel UPS (10/15 kVA) User’s Guide S164201601 Rev A www.powerware.com 1
Chapter 1 Introduction
A parallel system with up to four uninterruptible power supplies (UPSs)
can be installed to provide a parallel capacity and/or redundant system.
This load sharing system provides more capacity than a single UPS and
can provide backup, depending on the load and configuration. In
addition, when one UPS is taken out of service for maintenance or is not
operating properly, a redundant UPS continues to supply uninterrupted
power to the critical load. A parallel Powerware®Hot Sync®Computer
Area Network (CAN) Bridge Card provides connectivity for system
metering and operational mode control. The parallel system consists of
two to four UPSs, each with a parallel CAN Bridge Card and a parallel
cabinet.
Figure 1 shows the Powerware 9355 UPS and an optional Extended
Battery Module (EBM).
Figure 1. The Powerware 9355 UPS and EBM (3-High Cabinets Shown)
INTRODUCTION
EATON Powerware®9355 Parallel UPS (10/15 kVA) User’s Guide S164201601 Rev A www.powerware.com
2
EATON Powerware®9355 Parallel UPS (10/15 kVA) User’s Guide S164201601 Rev A www.powerware.com 3
Chapter 2 Safety Warnings
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This manual contains important instructions that you should follow during installation and
maintenance of the UPS and batteries. Please read all instructions before operating the
equipment and save this manual for future reference.
DANGER
This UPS contains LETHAL VOLTAGES. All repairs and service should be performed by
AUTHORIZED SERVICE PERSONNEL ONLY. There are NO USER SERVICEABLE PARTS
inside the UPS.
WARNING
SThis UPS contains its own energy source (batteries). The UPS output may carry live
voltage even when the UPS is not connected to an AC supply.
STo reduce the risk of fire or electric shock, install this UPS in a temperature and humidity
controlled, indoor environment, free of conductive contaminants. Ambient temperature
must not exceed 40°C (104°F). Do not operate near water or excessive humidity (95%
maximum).
STo reduce the risk of fire, connect only to a circuit provided with 100 amperes maximum
branch circuit overcurrent protection in accordance with the National Electrical Code,
ANSI/NFPA 70.
SOutput overcurrent protection and disconnect switch must be provided by others.
CAUTION
SBatteries can present a risk of electrical shock or burn from high short circuit current.
Observe proper precautions. Servicing should be performed by qualified service
personnel knowledgeable of batteries and required precautions. Keep unauthorized
personnel away from batteries.
SProper disposal of batteries is required. Refer to your local codes for disposal
requirements.
SNever dispose of batteries in a fire. Batteries may explode when exposed to flame.
SAFETY WARNINGS
EATON Powerware®9355 Parallel UPS (10/15 kVA) User’s Guide S164201601 Rev A www.powerware.com
4
Consignes de Sécurité
CONSIGNES DE SÉCURITÉ IMPORTANTES
CONSERVER CES INSTRUCTIONS
CE MANUEL CONTIENT DES CONSIGNES DE SÉCURITÉ
IMPORTANTES
DANGER!
Cet onduleur contient des TENSIONS MORTELLES. Toute opération d’entretien et de
réparation doit être EXCLUSIVEMENT CONFIÉE A UN PERSONNEL QUALIFIÉ AGRÉÉ.
AUCUNE PIÈCE RÉPARABLE PAR L’UTILISATEUR ne se trouve dans l’onduleur.
WARNING
SCet onduleur renferme sa propre source d’énergie (batteries). Les prises de sortie
peuvent être sous tension même lorsque l’onduleur n’est pas branché sur le secteur.
SPour réduire les risques d’incendie et de décharge électrique, installer l’onduleur
uniquement à l’intérieur, dans un lieu dépourvu de matériaux conducteurs, où la
température et l’humidité ambiantes sont contrôlées. La température ambiante ne doit
pas dépasser 40 °C. Ne pas utiliser à proximité d’eau ou dans une atmosphère
excessivement humide (95 % maximum).
SLa protection contre une surintensité pour le(s) circuit(s) de sortie de courant alternatif
doit être fournie par un autre fournisseur.
SLes interrupteurs de déconnexion convenables pour le(s) circuit(s) de sortie de courant
alternatif doivent être fournie par un autre fournisseur.
ATTENTION!
SLes batteries peuvent présenter un risque de décharge électrique ou de brûlure par des
courts-circuits de haute intensité. Prendre les précautions nécessaires.
SUne mise au rebut réglementaire des batteries est obligatoire. Consulter les règlements
en vigueur dans votre localité.
SNe jamais jeter les batteries au feu. L’exposition aux flammes risque de les faire
exploser.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Eaton UPS
Eaton
Eaton Powerware 9395 Manuel utilisateur
Eaton
Eaton Powerware 9130 Manuel utilisateur
Eaton
Eaton CA22106060000R6 Manuel utilisateur
Eaton
Eaton 5E 500 Manuel utilisateur
Eaton
Eaton MBP11K208 Manuel utilisateur
Eaton
Eaton 5P 1550VA Manuel utilisateur
Eaton
Eaton 9395-275 Manuel
Eaton
Eaton 3S850D Manuel utilisateur
Eaton
Eaton Pulsar Series 650 Manuel utilisateur
Eaton
Eaton 9130 Series Guide de démarrage rapide
Eaton
Eaton 3S 700 Manuel utilisateur
Eaton
Eaton 9315 Manuel utilisateur
Eaton
Eaton 9PX5KP1 Instructions d'installation et d'utilisation
Eaton
Eaton 9PXM Manuel utilisateur
Eaton
Eaton Power Xpert PXGX Manuel de programmation
Eaton
Eaton 93PS Guide de configuration
Eaton
Eaton Powerware 9x55 series Manuel
Eaton
Eaton E Series DX Manuel utilisateur
Eaton
Eaton 5E Manuel utilisateur
Eaton
Eaton Powerware 5125 Manuel utilisateur
Manuels UPS populaires d'autres marques
Pylontech
Pylontech Victron & Pylontech US5000 Manuel utilisateur
Tecnoware
Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur
Mecer
Mecer ME-1000-WTU Manuel utilisateur
Mustek
Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation
Emerson
Emerson Liebert NXL series Manuel utilisateur
MAKELSAN
MAKELSAN BOXER SERIES Manuel utilisateur
