Eastwood 31753 Manuel utilisateur

3/8"IMPACT AIR RATCHET

INSTRUCTIONS

Item #31753

2Eastwood Technical Assistance: 800.343.9353 >> techelp@eastwood.com

The EASTWOOD 3/8” IMPACT AIR RATCHET offers high performance in a compact, soft-grip,

lightweight aluminum housing that ﬁts in the tightest areas. It features a powerful, four-vane,

ball bearing motor with an efﬁcient twin-hammer drive. Includes forward and reverse with an

inﬁnitely variable throttle control.

CONTENTS

(1) Right Angle, 3/8” Square Drive

Pneumatic Ratchet

(1) 1/4” MNPT, Male M-type

Quick Disconnect Inlet Fitting

SPECIFICATIONS

• Square Drive: 3/8” with Ball Detent

• RPM: 700 free speed

• Maximum Torque: 45 ft-lbs [61 N-m]

• Air Consumption: 3.1 CFM [87.8 L/m] @ 90 PSI

• Inlet thread size: 1/4” FNPT

• Reversible, Variable Speed, 4 Vane, Ball Bearing Air Motor

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION used with the safety alert symbol, indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

NOTICE is used to address practices not related to personal injury.

SAFETY INFORMATION

The following explanations are displayed in this manual, on the labeling, and on all other information

provided with this product:

To order parts and supplies: 800.343.9353 >> eastwood.com 3

READ INSTRUCTIONS

• Thoroughly read and understand these product instructions before using

this tool. Failure to follow all warnings can result in tool damage or serious

physical injury.

• Keep these product instructions for future reference.

EYE INJURY HAZARD!

• Tool can eject metal particles, dirt and debris at high velocity.

Always wear ANSI approved eye protection when operating this tool.

HEARING DAMAGE HAZARD!

• This Eastwood Pneumatic Tool emits high sound levels while operating.

Use ANSI approved ear protection when operating.

BURSTING HAZARD!

• Do not exceed 90 psi (6.2 bar) of tool inlet pressure. Permanent tool damage

and/or explosion could occur and cause personal injury.

INJURY HAZARD!

• The tool can suddenly kick back or twist causing severe hand or wrist injury.

• Always make sure the workpiece is securely clamped or anchored to avoid

sudden movements which could result in injury.

• Frequently inspect Air Ratchet and socket (not Included) condition.

If cracks develop, discontinue use immediately and replace damaged socket.

• Always disconnect tool from air supply when changing sockets and

accessories to prevent accidental tool starting and potential injury.

VIBRATION INJURY HAZARD!

• This tool can vibrate during use! Repeated exposure to vibration may cause

physical injury.

SAFETY INFORMATION

4Eastwood Technical Assistance: 800.343.9353 >> techelp@eastwood.com

SET-UP

• Using a good quality Teﬂon sealing tape (not Included), thread the 1/4” MNPT, Male quick

disconnect inlet ﬁtting into the air inlet.

CONNECTION

• Be sure that the air supply to the tool is clean and dry. Moisture in the supply line will

quickly damage the motor and valves.

• A minimum 3/8” I.D. air line should be used for optimal performance.

OPERATION

• With air supply disconnected, snap selected socket or accessory over the retaining ball nested

in the square drive.

• Connect air supply, hold tool securely and depress Paddle to begin rotating action.

Speed is regulated by pressure applied to the Paddle.

• To loosen fasteners, rotate knob on the back of the drive head Clockwise toward the “R”.

To tighten fasteners, rotate knob Counter-clockwise toward the “F”.

INJURY HAZARD!

To avoid injury, always disconnect air supply to tool when attaching or

removing sockets or accessories.

To avoid injury, only use sockets and accessories rated for “Impact” use.

To order parts and supplies: 800.343.9353 >> eastwood.com 5

MAINTENANCE

• Add several drops of air tool oil before each use by dropping directly into the air inlet.

• If tool is to be unused for an extended period, add 10 drops of air tool oil directly to the air inlet,

rotate the tool motor by hand several times to distribute the oil throughout the motor then store

the tool, handle up.

PROBLEM CAUSE CORRECTION

Tool doesn’t

respond to

Paddle

depression

Insufﬁcient vol-

ume of air (CFM)

to operate tool.

Verify sufﬁcient air supply to tool.

(3.1 CFM @ 90 PSI minimum requirement)

Moisture or other

contamination in

air supply

Check for moisture in air line and tool air inlet.

Tool perfor-

mance is slow

or sluggish

Insufﬁcient vol-

ume of air (CFM)

to operate tool

Verify sufﬁcient air supply to tool.

(3.1 CFM @ 90 PSI minimum requirement).

Moisture or other

contamination in

air supply

Check for moisture in air line and tool air inlet.

Air Motor is lack-

ing lubrication

Stop use immediately and add air tool oil

directly to air inlet.

Tool is exces-

sively noisy/

emits high

pitched sound

Air Motor is lack-

ing lubrication

Stop use immediately and add air tool oil

directly to air inlet.

TROUBLESHOOTING

6Eastwood Technical Assistance: 800.343.9353 >> techelp@eastwood.com

NOTES

To order parts and supplies: 800.343.9353 >> eastwood.com 7

NOTES

If you have any questions about the use of this product, please contact

The Eastwood Technical Assistance Service Department: 800.343.9353 >> email: techelp@eastwood.com

PDF version of this manual is available at eastwood.com

The Eastwood Company 263 Shoemaker Road, Pottstown, PA 19464, USA

800.343.9353 eastwood.com

ADDITIONAL ITEMS

#70491 Eastwood Industrial Air Hose, 3/8” x 25’

#70492 Eastwood Industrial Air Hose, 3/8” x 50’

Table des matières

Autres manuels Eastwood Outils électriques

Eastwood

Eastwood 13622 Manuel utilisateur

Eastwood

Eastwood Perfect Panel Prep Tool Manuel utilisateur

Eastwood

Eastwood 13650 Manuel utilisateur

Eastwood

Eastwood 21560 Manuel utilisateur

Eastwood

Eastwood 20198 Manuel utilisateur

Eastwood

Eastwood B60 Manuel utilisateur

Eastwood

Eastwood 13475 Manuel utilisateur

Eastwood

Eastwood 31338 Manuel utilisateur

Eastwood

Eastwood 33862 Manuel utilisateur

Eastwood

Eastwood 31483 Manuel utilisateur

Eastwood

Eastwood 30216 Manuel utilisateur

Eastwood

Eastwood 2-PS Manuel utilisateur

Eastwood

Eastwood 51460 Manuel

Eastwood

Eastwood 21640 Manuel utilisateur

Eastwood

Eastwood 14041 Manuel utilisateur

Eastwood

Eastwood 11737 Manuel utilisateur

Eastwood

Eastwood 32498 Manuel utilisateur

Eastwood

Eastwood 13630 Manuel utilisateur

Eastwood

Eastwood 20198 Manuel utilisateur

Eastwood

Eastwood 32290 Manuel utilisateur

Eastwood

Eastwood 21304 Manuel utilisateur

Eastwood

Eastwood 21749 Manuel utilisateur

Eastwood

Eastwood 11797 Manuel utilisateur

Eastwood

Eastwood 20646 Manuel utilisateur

Manuels Outils électriques populaires d'autres marques

AEG

AEG OMNI-JS Manuel utilisateur

SIP

SIP 01533 Manuel utilisateur

Ribimex

Ribimex PRS499 Manuel utilisateur

3M Fiber Optic Connector Crimp Tool Manuel utilisateur

Ryobi

Ryobi P524 Manuel utilisateur

ROJEK

ROJEK FSN 300A Manuel utilisateur

Kemper

Kemper 1740PRO Manuel utilisateur

WABCO

WABCO OptiTire Manuel utilisateur

EINHELL

EINHELL TE-MS 18/210 Li Manuel utilisateur

Orgapack

Orgapack OR-T 85 Guide rapide

TOUGHCUT

TOUGHCUT Diamond 400 Manuel utilisateur

Yaros

Yaros PB-3603 Manuel utilisateur

Fein

Fein BSS 2.0 E Guide de configuration

Baileigh Industrial

Baileigh Industrial SS-2725 Manuel utilisateur

Milwaukee

Milwaukee 2674-20 Manuel utilisateur

Fein

Fein BLs 1.6 Manuel utilisateur

Princess

Princess Electric Multi Sharpener Manuel utilisateur

FOREDOM

FOREDOM K.1050 Manuel