Earth Way 2600A-Plus Estate Manuel utilisateur

Frame

Upper handles

Gauge &

Linkage

Assembly

Handle Shaft

Lower

Handles

Wheels

Impeller

Gearbox

Axle

Control Rod

Frame Braces

1. Remove and identify all loose parts from carton.

#10 X 1-1/4”

Flat Head Screw

Pt# 52215 PAGE 1

EV-N-SPRED

EarthWay

2600A-Plus EstAtE

BroAdcAst sPrEAdEr

ASSEMBLY and OPERATING INSTRUCTIONS Rev. 3-10

HELPFUL HINTS: REVIEW THE DIRECTIONS BEFORE ASSEMBLY

;Make sure the ARROW on the gear box points to the front of the spreader. The impeller must turn clockwise. Reversing

the gearbox will cause the impeller to turn counter clockwise. Clean the impeller plate after each use. Fertilizer stuck on the

impeller blades will cause uneven spreading.

;Your spreader is designed to be pushed at three miles per hour, which is a brisk walking speed. Slower or faster speeds

will change the spread patterns. Wet fertilizer will also change the spread pattern and ow rate. Clean and dry your

spreader thoroughly after each use. A coating of light spray oil will help prevent corrosion. Wash between the shut off

plate and bottom of the hopper.

;Gears are permanently lubricated at the factory. Do not open the gearbox or dirt may enter.

IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY QUESTIONS REGARDING

THE SAFE OPERATION OF THIS SPREADER, PLEASE CONTACT US. THIS MODEL INCLUDES LIFETIME TECHNICAL

SUPPORT SUPPORT HOT LINE: 574-848-7491 or 800-294-0671, EmAil: tEchsuPPort@EArthwAy.com

2. Position hopper as shown to the right.

Install Frame using (4) #10 x 1¼” Flat

Head Phillips screws. TIGHTEN

THESE NOW

3. Install gear box by inserting the pinion shaft into hole in center of

hoppers bottom. The ARROW on the gearbox must point to FRONT of

the hopper. Follow label instructions on hopper.

Arrow

1/4 - 20 Lock-nut

1/4 - 20 x 1-1/2” Bolt

Handle Shaft

Right

Side Left

Side

Slide Axle Through as shown

1/4-20 x 2-1/4”

Bolt 1/4-20 x 2-1/4”

Bolt

Axle Bearing

Flat

Side

Notch

4. Install lower handles onto Frame and secure with ¼-20 x 2 ¼” bolt

through hole in Frame Braces and through the hole in frame install

locknut.

 Next,Slidetheaxle(CoaStWheelSidefirSt) through the right

side lower handle and into the gearbox (with the arrow facing the

FRONT), you will need to rotate the axle to engage with the gearbox,

then through the left side lower handle.

TURN SPREADER UPRIGHT ON TO WHEELS.

PAGE 2

8. Install Handle Shaft as shown below using (2) 1/4-20 x

1½” Hex Bolt and (2) 1/4-20 Locknuts

5. Install the bearings over the axle and

press into the notches of the lower

handle as shown above.

Right

Side

DRIVE WHEEL

Left

Side

COAST WHEEL

Slide wheels on axle as shown

33106

1/8" X 3/4" Cotter Pin

33107

1/8" X 1-3/4" Cotter Pin

34103

1" OD. Washer

~~~IMPORTANT~~~

CoastDrive

Upper Handle

1/4 - 20 Lock-nut

1/4 - 20 x 1-1/2” Bolt

6. Install drive wheel to axle using pin hole nearest to lower handles

as shown. Insert 1¾” Cotter pin through wheel and through axle.

Bend with pliers to prevent pin from falling out.

7. Install coast wheel to axle using outside pin hole. As shown, add the

at washer, and insert ¾” Cotter pin through axle (not thru the wheel). Bend with pliers to prevent pin from falling out.

NOW GO BACK AND TIGHTEN ALL NUTS

AND BOLTS, DO NOT OVER TIGHTEN.

9. Insert (2) 1/4-20 x 1½” Hex Bolt

through Gauge and Linkage Assembly, then through the Upper Handle, Handle

Shaft, Upper Handle and secure with (2) 1/4-20 Locknuts as shown at the right.

PAGE 3

1/4 - 20 Locknut

1/4 - 20 x 1-1/2” Bolt

1/4 - 20

Locknut

Gauge & Linkage Assembly

Control Lever

& Gauge

12. CALIBRATION: this stEP EnsurEs thAt your sPrEAdEr is ProPErly

AdjustEd to givE you A corrEct stArting Point to APPly mAtEriAls At thE corrEct

sEtting. Pull the Control Lever back to #30 on the Gauge, then push the shut-off plate

forward until the shut-off and the drop holes are fully open. Now tighten the Hex Nut on

the ½” Carriage Bolt on the Linkage Assembly. Check to conrm calibration by closing the

Control Lever, then reopening to #30 and conrm that the drop holes are fully open.

13. Insert agitator to pinion shaft on inside of hopper.

NOTE: Position of at side of the agitator as shown at the

right.

10. Attach Linkage Pivot with 1/4-20 x 1½” Hex Bolt, Flat

Washer, Spacer and Locknut as shown below. Next install

Control Rod into the Shut-Off Plate as shown at the right.

TIP: Make sure that the Control Rod is above the Lower

Handles.

60088

Gauge & Linkage

12147

Spacer

32103

1/4-20 Locknut

31100

1/4-20 X 1-1/2" Bolt

and 34108 Washer

41256

Control

Rod

36500

1/2” Carriage

Bolt

34100

Washer

32108

Hex Nut

60088

Linkage

12317

Shut-off

Plate

41256

Control

Rod

25304

Handle Shaft

12317

Shut-Off

Plate

60088

Linkage

32108

Hex Nut

34100

Washer

41256

Control

Rod

11. Using ½” Carriage Bolt, install through the Control Rod, Linkage and install the Flat

Washer and secure with Hex Nut to a loose t to allow for CALIBRATION below. See

above right and below for details.

PAGE 4

The settings furnished on the Rate Setting Matrix are intended as a guide only. Variations in physical characteristics of

material applied, walking speed, and roughness of ground surface may require slightly different spreader settings. Due to the

above conditions, the manufacturer makes no warranty as to the uniformity of coverage actually obtained from the settings

listed.

5-YEAR LIMITED WARRANTY

EarthWay

Products, Inc. warrants this product to be free of defects in original workmanship and materials for a period

of 5-Years to the end user with the original purchase receipt. If a manufacturing non-conformance is found,

EarthWay

Products, Inc. at its discretion will repair or replace the part(s) or product at no charge provided the failure is not the result of

incorrect installation, mishandling, misuse, tampering, or normal wear and tear as determined by

EarthWay

at its discretion may require that the part(s) or product be returned along with the original purchase receipt at owners’

expense for examination and compliance with the terms of this warranty. (Do not return any product without rst receiving

authorization from

EarthWay

Products, Inc.). To seek remedy under this warranty, contact

EarthWay

Products, Inc. at

574-848-7491, techsupport@earthway.com or write to (

EarthWay

Products, Inc. P.O. Box 547 Bristol, Indiana 46507)

and describe the nature of the manufacturing defect. SPECIFIC LIMITATIONS: This warranty covers only the part(s) or

product; any labor charges associated with repair or replacement of non-conformances are specically excluded. Due to

the corrosive nature of most fertilizers and ice melt products,

EarthWay

Products, Inc. makes no warranty against and

specically excludes part(s) or product degradation or failure due to corrosion or its effects. Clean and dry your spreader

thoroughly after each use, as a preventative measure, coat all metal parts with a light oil or silicon spray.

HOW TO ORDER SPARE PARTS

All spare parts listed herein may be ordered direct

from the manufacturer. Be sure to give the following

information when ordering.

;Model Number

;Part Number

;Part Description

You can contact us by calling (574) 848-7491 or

800-294-0671 to place an order using a credit card.

Questions? parts@earthway.com

OPERATING INSTRUCTIONS

Before lling hopper, become familiar with the operation of this spreader.

1. Obtain proper setting for material to be used from the RATE SETTING MATRIX included with this spreader.

2. Move stop bolt on rate gauge assembly to the proper setting for the material that you are spreading.

3. While pushing spreader forward, pull the Control Lever back to stop bolt.

4. To stop, push lever forward to close ow holes before you stop moving.

5. When nished, empty any remaining material from hopper.

6. Thoroughly wash spreader and allow to dry before storing. Spray all metal surfaces (inside & outside) with WD-40 or

other light oil to help prevent corrosion.

Full Rate Path Half Rate Path

Start

Finish

Start

Finish

77000

OPTIONAL

Heavy-Duty

Rain Cover

Drive Wheel

Side

Coast Wheel

Side

EarthWay

Products, Inc.

P.O. Box 547

Bristol, IN 46507

Phone: 800-294-0671

www.earthway.com

2600APlus Broadcast Spreader ~ Parts List

Key # Part # Description Key # Part # Description

1 19115 .875" ID. X 4" IL. BLACK GRIP 18 12128 LEFT FRAME BRACE

2 25403 UPPER HANDLE 19 31106 1/4-20 X 2 1/4" HHCS ZINC

3 32103 1/4-20 NYLON INS LOCKNUT ZINC 20 25107 FRAME

4 36500 #10-24 X 1/2" CARRIAGE BOLT SS 21 31138 #8 X 3/8" PMT #8 HD COARSE BLACK

5 33117 AGITATOR 22 12317 SHUT OFF PLATE

6 12251 HOPPER BUSHING 23 31108 #10 X 1 1/4" TYPE A FHPS ZINC

7 60089 HOPPER ASSEMBLY 24 12248 IMPELLER

8 60088 GAUGE & LINKAGE ASSEMBLY 25 60451 GEAR BOX ASSEMBLY

9 31100 1/4-20 X 1 1/2 HHMS ZINC 26 12167 SPLIT BEARING

10 34108 9/16" OD. X .257 ID. WASHER ZINC 27 12206 DUST COVER

11 12147 SPACER (PIVOT LINK) 28 33107 1/8" X 1 3/4" COTTER PIN SS

12 41256 CONTROL ROD 29 70149 9 IN PNEUMATIC WHEEL

13 34100 #10 FLAT WASHER SS 30 34103 1"OD X 17/32"ID X 1/32" WASHER ZINC

14 32108 10-24 HEX. NUT ZINC PLATED 31 33106 1/8" X 3/4" COTTER PIN ZINC

15 25304 HANDLE SHAFT 32 23519 AXLE

16 25210 LOWER HANDLE OPTIONAL 77000 HEAVY DUTY RAIN COVER 10.5”

17 12129 RIGHT FRAME BRACE

Table des matières

Autres manuels Earth Way Épandeur

Earth Way

Earth Way 2170T Tow Manuel utilisateur

Earth Way

Earth Way 2170 Manuel utilisateur

Earth Way

Earth Way EV-N-SPRED C22HD Manuel utilisateur

Earth Way

Earth Way 2100P Estate Manuel utilisateur

Earth Way

Earth Way EV-N-SPRED Manuel utilisateur

Earth Way

Earth Way 3100 Manuel utilisateur

Earth Way

Earth Way 2600A-Plus Manuel utilisateur

Earth Way

Earth Way POLAR TECH 90365 Instructions d'installation

Earth Way

Earth Way EV-N-SPRED 2150 Manuel utilisateur

Earth Way

Earth Way EV-N-SPRED 2150 Manuel utilisateur

Earth Way

Earth Way M40 Manuel utilisateur

Earth Way

Earth Way EV-N-SPRED GT 3100 Manuel utilisateur

Earth Way

Earth Way FLEX-SELECT Series Manuel utilisateur

Earth Way

Earth Way 2050SU Manuel utilisateur

Earth Way

Earth Way FLEX-SELECT F80PSD Manuel utilisateur

Earth Way

Earth Way EV-N-SPRED M30 Manuel utilisateur

Earth Way

Earth Way Prizelawn BF l Manuel utilisateur

Earth Way

Earth Way Polar Tech 90365 Manuel utilisateur

Earth Way

Earth Way 2130 Manuel utilisateur

Earth Way

Earth Way Polar Tech 2040PI-PLUS Manuel utilisateur

Earth Way

Earth Way 2050T Manuel utilisateur

Earth Way

Earth Way EV-N-SPRED 2150 Manuel utilisateur

Earth Way

Earth Way 2050TP Manuel utilisateur

Earth Way

Earth Way EV-N-SPRED C24HD Manuel utilisateur

Manuels Épandeur populaires d'autres marques

PEQUEA

PEQUEA GT-100 Manuel utilisateur

Herculano

Herculano H2RS9 Manuel utilisateur

Epoke

Epoke SKE8 Manuel utilisateur

GEA

GEA EL44 Fiche technique

Boss Snowplow

Boss Snowplow TGS 800 Manuel utilisateur

Fisher

Fisher EMERSON 168 Series Manuel utilisateur

Fisher

Fisher POLY-CASTER 78601 Manuel utilisateur

TurfEx

TurfEx RS7200 Manuel du propriétaire

Ferris

Ferris Pathfinder Series Manuel utilisateur

Fayat Group

Fayat Group DYNAPAC S100 Guide de dépannage

Art's-Way Manufacturing

Art's-Way Manufacturing X700 Manuel d'installation et d'exploitation

EASTMAN

EASTMAN CR 500 Manuel utilisateur

Nogueira

Nogueira RoyalFlow-600 Manuel utilisateur

Buyers

Buyers TGS05B Manuel utilisateur

Magnum

Magnum V-BOX PV Series Supplément

Meyer's

Meyer's VB280 Manuel utilisateur

SnowEx

SnowEx VX-4210 Manuel utilisateur

Kramer

Kramer VM-400HDCP Manuel utilisateur