Duerkopp Adler 506-3 Mode d'emploi
506-3
Instructions, complete
Operating Instructions
Installation Instructions
Service Instructions
Postfach 17 03 51, D-33703 Bielefeld • Potsdamer Straße 190, D-33719 Bielefeld
Telefon +49 (0) 521 / 9 25-00 • Telefax +49 (0) 521 / 9 25 24 35 • www.duerkopp-adler.com
1
2
Ausgabe / Edition: Änderungsindex Teile-Nr./Part.-No.:
10/2008 Rev. index: 01.0 Printed in Federal Republic of Germany 0791 506011
3
Instructions, complete
506-3
Overview
Operating table
Operating Instructions
Installation Instructions
Service Instructions
Pneumatic circuit plan
9770 506002
Interconnection-diagram
9890 506003 B
All rights reserved.
Property of Dürkopp Adler AG and copyrighted. Reproduction or publication of the content in any manner,
even in extracts, without prior written permission of Dürkopp Adler AG, is prohibited.
Copyright © Dürkopp Adler AG - 2008
Foreword
This instruction manual is intended to help the user to become familiar
with the machine and take advantage of its application possibilities in
accordance with the recommendations.
The instruction manual contains important information on how to
operate the machine securely, properly and economically. Observation
of the instructions eliminates danger, reduces costs for repair and
down-times, and increases the reliability and life of the machine.
The instruction manual is intended to complement existing national
accident prevention and environment protection regulations.
The instruction manual must always be available at the machine/sewing
unit.
The instruction manual must be read and applied by any person that is
authorized to work on the machine/sewing unit. This means:
–Operation, including equipping, troubleshooting during the work
cycle, removing of fabric waste,
–Service (maintenance, inspection, repair) and/or
–Transport.
The user also has to assure that only authorized personnel work on the
machine.
The user is obliged to check the machine at least once per shift for
apparent damages and to immediatly report any changes (including the
performance in service), which impair the safety.
The user company must ensure that the machine is only operated in
perfect working order.
Never remove or disable any safety devices.
If safety devices need to be removed for equipping, repairing or
maintaining, the safety devices must be remounted directly after
completion of the maintenance and repair work.
Unauthorized modification of the machine rules out liability of the
manufacturer for damage resulting from this.
Observe all safety and danger recommendations on the machine/unit!
The yellow-and-black striped surfaces designate permanend danger
areas, eg danger of squashing, cutting, shearing or collision.
Besides the recommendations in this instruction manual also observe
the general safety and accident prevention regulations!
General safety instructions
The non-observance of the following safety instructions can cause
bodily injuries or damages to the machine.
1. The machine must only be commissioned in full knowledge of the
instruction book and operated by persons with appropriate training.
2. Before putting into service also read the safety rules and
instructions of the motor supplier.
3. The machine must be used only for the purpose intended. Use of
the machine without the safety devices is not permitted. Observe all
the relevant safety regulations.
4. When gauge parts are exchanged (e.g. needle, presser foot, needle
plate, feed dog and bobbin) when threading, when the workplace is
left, and during service work, the machine must be disconnected
from the mains by switching off the master switch or disconnecting
the mains plug.
5. Daily servicing work must be carried out only by appropriately
trained persons.
6. Repairs, conversion and special maintenance work must only be
carried out by technicians or persons with appropriate training.
7. For service or repair work on pneumatic systems, disconnect the
machine from the compressed air supply system (max. 7-10 bar).
Before disconnecting, reduce the pressure of the maintenance unit.
Exceptions to this are only adjustments and functions checks made
by appropriately trained technicians.
8. Work on the electrical equipment must be carried out only by
electricians or appropriately trained persons.
9. Work on parts and systems under electric current is not permitted,
except as specified in regulations DIN VDE 0105.
10. Conversion or changes to the machine must be authorized by us
and made only in adherence to all safety regulations.
11. For repairs, only replacement parts approved by us must be used.
12. Commissioning of the sewing head is prohibited until such time as
the entire sewing unit is found to comply with EC directives.
13. The line cord should be equipped with a country-specific mains
plug. This work must be carried out by appropriately trained
technicians (see paragraph 8).
It is absolutely necessary to respect the safety
instructions marked by these signs.
Danger of bodily injuries !
Please note also the general safety instructions.
Contents Page:
Part 3: Service Instructions Cl. 506-3
1. General .................................................... 3
2. Removing the top cover and turning over the upper part of the machine
2.1 Removingthetopcover........................................... 4
2.2 Turning over the upper part of the machine ............................... 6
3. Shuttle, needle bar
3.1 Needle bar height............................................... 7
3.2 Synchronizing the shuttle and needle bar movements......................... 9
3.3 Shuttle-tip/needle distance ......................................... 10
3.4 Driver/needle distance ........................................... 11
3.5 Loop stroke .................................................. 13
4. Bobbin ejector ................................................ 14
5. Disc cam
5.1 Replacingthedisccam........................................... 17
5.2 Fittingtheintermediatetransmission................................... 20
5.3 Replacing the worm-gear pair and worm screw ............................. 21
5.3.1 Fit/Remove the synchronous motor .................................... 21
5.3.2 Replacing the worm-gear pair and worm screw ............................. 23
5.4 Worm-screw wheel play ........................................... 24
6. Shut-down devices
6.1 Basicstopposition(switchS7)....................................... 27
7. Clamps and table plate
7.1 Position of table plate with respect to the needle ............................ 29
7.2 Positionofclampswithrespecttothetableplate............................ 32
8. Thread advance ............................................... 33
9. Thread-tensioning spring ......................................... 34
10. Needle cooling ................................................ 35
3
Contents Page:
11. Thread-burning device
11.1 Threadextractor ............................................... 36
11.2 Upper burning device ............................................ 38
11.2.1Startingposition................................................ 38
11.2.2 Position of fully-extended burner ..................................... 39
11.2.3Adjustingtheburnerheight-stop...................................... 40
11.2.4 Burner angle.................................................. 41
11.3 Lowerburningdevice ............................................ 42
11.3.1 Adjustment preconditions .......................................... 42
11.3.2Distancebetweenthreadextractorandburner............................. 43
11.3.3Positionofburnerwhenswivelledforwards............................... 43
11.3.4Burnerheight................................................. 44
11.3.5 Thread-extractor height ........................................... 44
12. Thread-suction device ........................................... 45
13. Bobbin-winder adjustment ........................................ 46
14. V-belt tension ................................................ 47
2
1. General
These service instructions describe the adjustment of the automatic
sewing machine in an appropriate order.
CAUTION:
Various adjustments are mutually dependent.
It is therefore essential for adjustments to be carried out in the order
described.
CAUTION:
The activities described in these servicing instructions may be carried
out only by experts or by persons with the appropriate training.
Danger of breakage
It is essential for the adjustments specified in these servicing
instructions to be carried out before the machine is recommissioned
following disassembly.
Never start the machine with the drive motor rotating in the wrong
direction.
A sewing run may not commence unless the head cover and the
shuttle-area cover are closed.
If either of these is open, all control functions are blocked.
CAUTION: danger of injury
Prior to all repair, modification and maintenance work the main switch
must be turned off and the machine disconnected from the
compressed-air supply.
Adjustment work and function testing carried out with the machine
running require the utmost care and observance of all safety
precautions.
Setting gauges
We can supply the following setting gauges on request:
Setting gauge Use Order No.
Gauge Loop-stroke adjustment 0981 150009
Calliper Loop-stroke adjustment 0981 150006
Gauge Adjusting the arm-shaft 7270 159160
eccentric (optional)
3
3
2. Removing the arm cover and Turning over the upper part of the machine
2.1 Removing the arm cover
For service work in the interior of the upper part of the machine the
arm cover 3 must be removed.
First the control unit 1 must be swivelled aside and the bobbin-winder
cartridge 2 removed.
CAUTION: danger of injury
Turn off the main switch and disconnect the machine from the
compressed-air supply.
The arm cover must not be removed until both these steps have been
taken.
Swivelling the control unit aside
–Slightly undo Allen screws 5.
These are accessible through the holes 4 in the casing.
–Carefully swivel the control unit aside.
4
321 54
Removing the bobbin-winder cartridge
–Undo fixing screws 6.
–Lift off bobbin-winder cartridge.
Removing the arm cover
–Undo arm-cover fixing screws 2.
–Carefully raise the arm cover 2 and fold it back.
–Remove compressed-air hose 7 from the quick-release fastening:
Push the ring 8 to the right and pull the hose out of the
quick-release fastening.
CAUTION :
The use of force to remove the arm cover may cause damage to the
compressed-air line.
3
5
627
78
2.2 Turning over the upper part of the machine
For service work on the underside of the upper part of the machine the
upper part must be turned over.
CAUTION: danger of injury
Turn off the main switch.
The upper part of the machine must not be turned over unless
themainswitchisoff.
–Carefully turn over the upper part of the machine until it is
supported by the table-plate prop.
The underside of the upper part of the machine is now accessible
for service work.
6
Autres manuels pour 506-3
2
Table des matières
Autres manuels Duerkopp Adler Machine à coudre
Duerkopp Adler
Duerkopp Adler 221 Mode d’emploi
Duerkopp Adler
Duerkopp Adler 745-21 Mode d’emploi
Duerkopp Adler
Duerkopp Adler 506-3 CNC Manuel utilisateur
Duerkopp Adler
Duerkopp Adler 269 Mode d’emploi
Duerkopp Adler
Duerkopp Adler 739-23 Caractéristiques techniques
Duerkopp Adler
Duerkopp Adler 294 Mode d’emploi
Duerkopp Adler
Duerkopp Adler 550-16-23 Mode d'emploi
Duerkopp Adler
Duerkopp Adler 550-12-23 Mode d'emploi
Duerkopp Adler
Duerkopp Adler 841-27 Manuel utilisateur
Duerkopp Adler
Duerkopp Adler Electropneumatic Fullness Kit 0175 590044 Manuel utilisateur
Duerkopp Adler
Duerkopp Adler 167-372 Mode d’emploi
Duerkopp Adler
Duerkopp Adler 4260-6 Guide de dépannage
Duerkopp Adler
Duerkopp Adler 212 Mode d’emploi
Duerkopp Adler
Duerkopp Adler 550-16-26 Manuel utilisateur
Duerkopp Adler
Duerkopp Adler DAP 6-300-1-6 Mode d’emploi
Duerkopp Adler
Duerkopp Adler 540-100-1 Manuel utilisateur
Duerkopp Adler
Duerkopp Adler 929 Mode d’emploi
Duerkopp Adler
Duerkopp Adler 271 Manuel utilisateur
Duerkopp Adler
Duerkopp Adler 579 Manuel utilisateur
Duerkopp Adler
Duerkopp Adler 524 Manuel utilisateur
