DTS A.R.C. Manuel utilisateur

Architectural lighting

PROGETTO GRAFICO DTS Show division

USER MANUAL

A.r.c.

www.bluelight.at

INDEX

1- page. 4

2- page. 4

3- page. 5

4- page. 6

5- page. 6

6- page. 7

7- page. 9

9- CHANGING DMX ADDRESSES page. 9

10- DISPLAY PANEL OPERATION page. 10

11-

12- AUTOMATIC MODE page. 12

13- HIDDEN MENU page. 12

14- page. 13

15- DMX ADDRESSES page. 14

16 page. 17- ELECTRONIC CARD

TECHNICAL FEATURES

SAFETY INFORMATION

MOUNTING THE LAMPS

VOLTAGE AND FREQUENCY

INSTALLATION

MAINS CONNECTION

DMX SIGNAL CONNECTION

DISPLAY (disp) page. 11

PERIODIC CLEANING E CONTROL

370 mm 335 mm

475 mm

www.bluelight.at

1- TECHNICAL FEATURES

2- IMPORTANT SAFETY INFORMATION

Dmx colorchanger for architectural lighting internal or outdoor use ( Ip65)

Power supply

Power consumption:

Lamp:

Control:

Automatic mode

Linear dimmer

Shutte

Colours:

2 light beam angles (40° / 64°)

Working position: any position

Weight:

A.R.C.

A.R.C

: 230V 50-60 Hz

200 VA for CDM-T 150 lamp 300VA for MSD 250 lamp with in-built

factor correction

CDM-T 150 or MSD250 discharge lamp

4 channels DMX 512

8 dichroic filters with high chromatic yeld + white,

Different rotating speeds to produce RAINBOW effect.

15,5 kg

- uses a MSD250 or CDM-T 150 . The use of any alternative lamp is not

recommended and will null and void the fixture's warranty.

-Minimum distance from the closest illuminable surface: 0,5 m.

-Replace any blown or damaged fuses only with those of identical value. Refer to the wiring

diagram if there is any doubt.

-Connect the projector to mains power via a thermal magnetic circuit breaker.

-High voltage is present inside the unit. Isolate the projector from the mains supply prior to

performing any function which involves touching the inside of the unit, including lamp

replacement.

-The level of technology inherent in the . requires the assistance of specialised

personnel for all servicing. Refer all work to your authorised DTS service centre.

-A good earth connection is essential for proper functioning of the projector.

Never connect the unit without proper earth connection.

-Never turn the lamp on if the glass damaged. It respective shielding functions will only

operate efficiently if it is in perfect working order.

-Never look directly into the lamp when it is on.

2.1- Fire prevention:

2.2- Prevention of electric shock:

2.3- Protection against ultraviolet radiation:

r: strobe max 8 flash/sec

www.bluelight.at

2.4- Safety:

2.5- Level of protection against the penetration of solid and liquid matter

-The projector should always be installed with bolts, clamps and other fixtures that are

capable of supporting the weight of the unit.

-Always use a second safety chain of a suitable rating to sustain the weight of the unit in case

of the failure of the main fixing point.

-The external surface of the unit, at various points, may exceed 100°C. Never handle the unit

until at least 10 minutes have elapsed since the lamp was turned off.

-Always replace the lamp if any physical damage is evident.

-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient

temperature should not exceed 35°C.

-A hot lamp may explode, so always wait for at least 10 minutes to elapse after the unit has

been turned off prior to attempting to replace the lamp.

Always wear suitable hand protection when handling the lamp.

-The projector is classified as an ordinary appliance and its level of protection against the

penetration of solid and liquid matter is IP 65.

The temperature inside the projector can reach 250° C after just 5 minutes, but it can get as

high as 350° C. Always check that the lamp is cold before attempting to remove it. In any

case, only open the appliance 10 minutes after it has been turned off.

1) Using a philips head screwdriver, remove the 3 screws placed on the rear end of the unit

so as to remove the lamp casing (photo 1).

2) Unscrew the three screws holding the lampsocket unit (photo2).

3) Remove the lampsocket unit and insert lamp in lampsocket (photo3).

3- MOUNTING THE LAMPS

WARNING: TURN POWER OFF BEFORE OPENING THE APPLIANCE.

Photo 1

Photo 2 Photo 3

www.bluelight.at

The lamp used is manufactured from quartz glass and should be handled with care. Always

adhere to the instructions supplied in the lamp's packaging. Never touch the glass directly but

use the tissue provided in the lamp's packaging. The Gy 9.5 lampbase (MSD250)is not

symmetrical; the G12 lampbase (CDM-T 150) is simmetrical.

. In case of difficulty, re-read the

instructions and repeat the procedure.

Attention: we recommend that the lamp be realigned in the optical train of the unit (Photo 4).

Alignment is carried out using the 3 adjusters.

During this operation you must bring the hot-spot to the centre of the beam and flatten it as

much as possible.

The projector can operate at 230V voltage, at 50-60Hz . D.T.S. presets a voltage of 230V at

a frequency of 50Hz (barring specific requests).

may be either floor or ceiling mounted.

For floor mounting installations, the is supplied with four rubber mounting feet (B)

on the base. For ceiling mounted installations, we suggest the use of appropriate clamps or

fixings to attach the fixture to the mounting surface.

Two holes situated at the base of the unit allow for the mounting of the unit with C clamps on

trussing.

DO NOT USE UNDUE FORCE ON THE GLASS

A.R.C.

3.1 -Alignment lamp:

4 -VOLTAGE AND FREQUENCY

5 -INSTALLATION

Photo 4

INSTALLAZIONE A TERRA

INSTALLAZIONE A SOFFITTO

www.bluelight.at

5.1 -Safety chain

5.2 -Protection against liquids:

5.3 -Risk of fire:

5.4 -Ambient temperature:

We recommend the use of a safety cable or chain connected to the and to the

suspension truss in order to avoid the fixture accidentally falling should the main fixing point

fail. Make sure that the iron cable or chain can bear the weight of the entire unit.

The attachment of the safety chain is accomplished by passing it through the handles as seen

in the figure

The projector contains electric and electronic components which should under no

circumstances come into contact with oil, water or any other liquid. The proper working of

the unit would be compromised should this occur.

Each fixture produces heat and must be installed in a well-ventilated position.

Minimum distance from the object being illuminated is 0,5 m.

The projector should never be installed in places that lack a constant flow of air. The ambient

temperature should NOT exceed 35°C.

operates at voltage 230V at 50 or 60Hz. Connect power cable to internal clamp

connector (photo1-2).

Prior to connecting the unit to your mains supply, ensure that the model in your

possessioncorrectly matches the mains supply available. For connection purposes, ensure that

your plug is of a suitable rating of 5A at 230V. Strict adherence to regulatory norms is

A.R.C.

6 -MAINS CONNECTION

Photo 2

Photo 1

SAFTEY CHAIN

www.bluelight.at

Architectural lighting

strongly recommended.

The use of a thermal magnetic circuit breaker is recommended for each A.R.C..

A good earth connection is essential for the correct operation of the projector.

The unit operates using a digital DMX 512 (1990) signal. Connection between the control

box and the projector or between projectors must be carried out using a two pair screened

ø0.5 mm cable.

Connect the control box signal to the DMX IN internal connector clamp (found at the base of

the unit) and connect it to the next projector by connecting the DMX OUT connector clamp

on the first projector to the DMX IN connector clamp on the second.

In this way, all the projectors are cascade connected.

6.1 -Protection:

7- DMX SIGNAL CONNECTION

NB. If the letters A001 flash on the display the possible causes are:

- No DMX signal

- The DMX address not valid

- There is a DMX reception problem

- The number of channels sent out by the mixer is inferior to 24

If the letters A001 appear on the display without flashing the DMX signal is being received

and is valid.

A...

(2)DATA -

(3)DATA+

(1)GND

(3)DATA+

(1)GND

(2)DATA -

DMX512

OUT

11=GND

2=DATA-

3=DATA+

CONTROLLER

STANDARD

DMX 512

OUT OUT

IN OUT

OUT

www.bluelight.at

8- DMX ADDRESSES:

A.R.C. To use 4 DMX channels.

Projector 1 A1

Projector 2 A11

Projector 3 A21

.....A...

Projector 6 A51

Projector 1 A1

Projector 2 A17

Projector 3 A33

....A...

Projector 6 A65

If you are using a DMX controller with 10 channels per projector set the following addresses

If you are using a DMX controller with 16 channels per projector set the following addresses

The address that has to be set on each projector generally depends on the number of channels that the DMX

mixer allots it.

If you have a 12 channel controller, set your to 10 CH MODE. The first projector will have an A001

address and if you want to select the next projector, then you have to add 12. The subsequent address will

then be A0013

A.R.C.

NB: The A.R.C. Needs a controller with at least 24 DMX channels to function properly.

For the next projector it is sufficient to add

“ 10”

“ 16”

9- CHANGING THE DMX ADDRESS

1) Press the UP-DOWN key until you reach the required DMX number. The numbers on the display will start

to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the projector is

now controlled by the new 512 DMX number.

WARNING: if you press the UP-DOWN keys together the channels are calculated more quickly and you get

a faster selection

www.bluelight.at

10- DISPLAY FUNCTIONS

Using the display panel it is possible to add functions and to vary some of the units

parameters. Altering the DTS default settings could change the way the unit responds to the

inputs given by the DMX controller, therefore it is important that the following functions be

followed and understood before carring out any changes.

Please note: the symbol is used in the following table to indicate a button that must be

pushed.

ENTER ENTER UP-DOWN

UP-DOWN

ENTER

ENTER UP-DOWN

ENTER

UP-DOWN ENTER

UP-DOWN

ENTER ENTER

UP-DOWN ENTER

COLOUR WHEEL SPEED

It is possible to change the speed

of the colour wheel, 18 different values

are available

UP-DOWN

DOWN

ENTER

SETTINGS

ENTER

DOWN

LED 1 LED 2

DISPLAY

Inverts the direction of display

depending on whether the unit

is placed upside down or upright

it also places the display in stand by mode.

TIMER

Lamp life display,

projector total running time.

reset of the lamp life

timer and

www.bluelight.at

UP-DOWN ENTER

UP-DOWN ENTER ENTER

UP-DOWN ENTER ENTER UP-DOWN

UP-DOWN

ENTER UP-DOWN

ENTER

UP-DOWN ENTER UP-DOWN ENTER

UP-DOWN ENTER

RESET

Resets both motors as well as

colour wheel and shutter.

Min.sec

UP-DOWN ENTER

11- DISPLAY (disp)

Using the menu it is possible to change the character direction of the display (POSI)

depending on whether you wish to mount the unit on the gorund our up-side down overhead.

It is also possible to activate the auto switch off (STBY) of the display after 3 minutes of

activity. However in standby mode a small red light will remain on indicating that the unit is

functioning, to reactivate the display it is sufficient to press any of the four buttons.

SOFTWARE VERSION

Circuit card software version check

DEFAULT

Reset to DTS defaults

AUTOMATIC

Automatic mode without DMX input, timer

mode and unit

activation on/off timer.

TEST MODE

Test mode for unit functions

www.bluelight.at

Table des matières

Autres manuels DTS Équipement d'éclairage

DTS

DTS DELTA 12 HEAD Manuel utilisateur

DTS

DTS HORUS FULL COLOUR Manuel utilisateur

DTS

DTS DELTA R FULL COLOR Manuel utilisateur

DTS

DTS XM 2500 Sport Manuel utilisateur

DTS

DTS ALCHEMY 5 Manuel utilisateur

DTS

DTS XR5 SPOT Manuel utilisateur

DTS

DTS 03.P16.02.01.LED PAR16 LED MR16 BLACK Manuel utilisateur

DTS

DTS DELTA 8 Series Manuel utilisateur

DTS

DTS Nick Wash 600 Manuel utilisateur

DTS

DTS FOS 100 WHITE 36 Manuel utilisateur

DTS

DTS Discharge Lamp 35-70-150W Manuel utilisateur

DTS

DTS Thomas & Betts NT 06 Manuel

DTS

DTS PAR 20 Manuel utilisateur

DTS

DTS SCENA COMPACT LED 50 Manuel utilisateur

DTS

DTS Alchemy 7 Manuel utilisateur

DTS

DTS Scena LED 150 Manuel utilisateur

DTS

DTS MOON 1200 Manuel utilisateur

DTS

DTS NICK NRG1200 CT Manuel utilisateur

DTS

DTS Scena LED 150 Manuel utilisateur

DTS

DTS Delta 8 White + Amber R Manuel utilisateur

DTS

DTS NICK NRG 1201 Manuel utilisateur

DTS

DTS XM 1200 SPOT Manuel utilisateur

DTS

DTS JACK Manuel utilisateur

DTS

DTS NicKWash 600 Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur

Silvair

Silvair MESH-CEDRP Manuel utilisateur