DSE RK Series Manuel utilisateur
INSTALLATION MANUAL
RK SERIES – DVR and NVR GUI 6.0
Page:2
Contents of the manual
The RK series DVRs and NVRs are video recording systems for CCTV video surveillance. NVR
models are used to connect IP cameras
The DVR models have BNC inputs to connect analog AHD, CVI, TVI, CVBS cameras but can also manage IP
cameras.
This manual explains how to install the video recorder, how to connect the cameras and how to use the
essential functions. It also explains how to connect from a computer with common clients.
For advanced configuration, remote access from the IoVedo.RK app and IoVedo.RK software, refer to the
specific manuals.
This manual refers to NVRs/DVRs withgraphical interface Version 6.0which you see below
If your NVR/DVR has a different interface, for example 5.0 or earlier, you can download the specific
manual for your version, or you can continue reading this manual considering that you will find the
same options on your screen, just with different graphics.
DSE SRL – ITALY – WWW.DSE.EU
INSTALLATION MANUAL
RK SERIES – DVR and NVR GUI 6.0
Page:3
Prepare the cameras
Before installing a DVR or NVR you must have the cameras to connect available. If you connect analog
cameras you must supply them with power and then connect the video signal with a coaxial cable or a
twisted pair with balun. If you connect IP cameras to the network you must first configure their IP address.
For these operations you must follow the camera manual.
DSE SRL – ITALY – WWW.DSE.EU
INSTALLATION MANUAL
RK SERIES – DVR and NVR GUI 6.0
Page:4
Install the Hard Disk
If you want your system to be able to record, you need to install a Hard Disk inside the video recorder. Any
3.5" SATA hard disk for computers is fine, but for longer life it would be better to purchase a specific model
for video recording.
The maximum capacity of the hard disk that you can mount is 8 TB.
Depending on the model, you can house from 1 to 8 Hard Disks inside the video recorder. You can easily
understand which direction the disk should be mounted by looking at the holes on the bottom of the DVR/NVR.
Remove the cover by unscrewing the side screws e
rear
Connect the hard disk with the two power and
data cables found inside. If there
there are multiple doors, choose any pair.
Secure the hard disk with the 4 screws provided
screw in from underneath the VCR
At the next startup, the NVR/DVR will reveal the new installed Hard Disk and ask you to start formatting it
in order to use it.
DSE SRL – ITALY – WWW.DSE.EU
INSTALLATION MANUAL
RK SERIES – DVR and NVR GUI 6.0
Page:5
CAUTION – The power consumption of a hard disk varies greatly depending on its capacity. Our video
recorders are supplied with a power supply suitable for a normal 1 or 2TB hard disk, normally the most
used size. If you install a larger hard disk or more than one hard disk, it is best to replace the standard
power supply with a higher power one.
DSE SRL – ITALY – WWW.DSE.EU
INSTALLATION MANUAL
RK SERIES – DVR and NVR GUI 6.0
Page:6
Connect a DVR
If you have purchased a DVR, your device can manage both analogue cameras, with its BNC inputs, and
IP cameras, via the network port.
These are the rear connections. The equipment varies based on the model you purchased.
A | VIDEO IN–To these BNC type video inputs you can connect any type of analog camera in AHD, CVI or
TVI technology, up to the maximum resolution managed by your DVR model. You can also connect old
CVBS analog cameras. The only cameras with a BNC connection that you cannot connect are SDI digital
cameras.
B | TO OUT–You can connect a speaker to this RCA connector to broadcast the DVR audio. Remember
that the HDMI monitor output also conducts audio so if you connect a TV via HDMI you can hear the
audio without connecting a speaker to this output.
C | V-OUT–To this BNC output you can connect an analog monitor, the AV input of a TV and any device
capable of receiving CVBS analog video. This output has low resolution and is not recommended to use
for the primary monitor. The resolution of this output is not sufficient to operate in the configuration
menu.
D | NET–It is the RJ45 network port. To be able to view your cameras via the Internet, or to
DSE SRL – ITALY – WWW.DSE.EU
INSTALLATION MANUAL
RK SERIES – DVR and NVR GUI 6.0
Page:7
connect IP cameras, you need to connect the DVR to your network. You must use a normal straight-type
network cable and insert it on one side into the NET port of the DVR and on the other into a free port on
your router or switch. The DVR is factory set to automatically configure itself on the network (DHCP).
And | AB RS485–This is the RS485 serial port to which you can connect the control pair to control analog
or AHD motorized cameras. While our latest motorized analog cameras support motion control along
the video cable by selecting UTC command protocol, older motorized analog cameras require these two
additional cables for control. The RS485 BUS is a twisted pair that connects in cascade all the analog
motorized units of your system. You can find more information in the camera manual on how it should
be connected, always respecting the A(+) and B(-) terminals found on the camera. You will then have to
configure the transmission protocol, in the PTZ configuration of the DVR, based on the camera. You need
to select the protocol, usually PelcoD, the speed, usually 1200,
Motorized IP cameras do not require this connection because they are controlled via the network cable.
F | VGA–You can connect a computer monitor that has this type of port to this output. This output
supports the maximum resolution of 1920x1080 FullHD.
G | INPUTS–You can connect alarm contacts to these terminals as explained later H | EXIT–You can
connect the alarm output to these terminals as explained later I | A1..A4–You can connect audio signals
from analog cameras or microphones to these RCA inputs. Remember that these audio inputs are only
active for BNC channels because IP cameras require the microphone to be connected to the camera.
L | HD OUT–This is the HDMI output for the monitor. Almost all TVs and PC monitors have this
connection port. If you connect a TV, to see the images you must remember to select the external HDMI
input you used for the NVR on your TV. This is typically done by pressing the SOURCE button on the
remote control. These DVRs come from the factory with a low output resolution which you can increase
up to 4K to match the maximum resolution of your monitor. This operation is explained better later in
the manual
Remember that the HDMI cable cannot be longer than a few meters. To connect an HDMI monitor
remotely from the NVR you must use an HDMI transmission device.
M | USB–To the USB ports you can connect the mouse included with the DVR and USD memories, such
as USB sticks or hard disks to back up video files. All DVRs also have a front USB port.
N | DC 12V–Connect the included 12VDC power supply here. Be careful not to confuse the DVR/NVR
power supply, which has at least 2A of power, with other smaller ones you have
DSE SRL – ITALY – WWW.DSE.EU
INSTALLATION MANUAL
RK SERIES – DVR and NVR GUI 6.0
Page:8
perhaps purchased for the cameras, because this would lead to malfunctions. If you power the DVR with
one of our centralized power supplies in the box you must consider that the individual outputs are
limited to 1A and this requires connecting at least 3 in parallel to be able to provide adequate power to
the DVR.
DSE SRL – ITALY – WWW.DSE.EU
INSTALLATION MANUAL
RK SERIES – DVR and NVR GUI 6.0
Page:9
Connect an NVR
If you have purchased an NVR your video recorder can only manage IP network cameras. These are the
rear connections. The equipment varies based on the model you purchased.
A-OUT-You can connect an external speaker to this minijack connector to broadcast audio. Remember
that the HDMI monitor output also conducts audio so if you connect a TV via HDMI you can hear the
audio without connecting this output.
VGA–You can connect a computer monitor to this output. This output supports the maximum resolution
of 1920x1080 FullHD.
HD–This is the HDMI output for the monitor. Almost all TVs and PC monitors have this connection port. If
you connect a TV, to see the images you must remember to select the external HDMI input you used for
the NVR on your TV. This is typically done by pressing the SOURCE button on the remote control. These
DVRs come from the factory with a low output resolution which you can increase up to 4K to match the
maximum resolution of your monitor.
Remember that the HDMI cable cannot be longer than a few meters. To connect a monitor remotely
from the NVR you must use an HDMI transmission device.
USB–You can connect the mouse included with the DVR and USB sticks to back up video files to the USB
ports. Many DVRs/NVRs also have a front USB port. You can also connect USB disks to record to external
HDDs
NET or LAN or WAN–It is the RJ45 network port. To be able to view your cameras via the Internet, or to
connect external IP cameras, you must connect the NVR to your network, for example to your router, via
this port. You must use a normal straight-type network cable and insert it on one side into the network
port of the NVR and on the other into a free port on your router or switch. The NVR is factory set to
automatically configure itself on the network (DHCP).
LAN1..8orPOE1..8– Some NVR models have POE ports to connect cameras. You can connect the IP
cameras you want the NVR to manage here. The NVR provides POE power to the cameras. If you connect
our RK Series cameras to these ports, they are automatically configured (plug and play). If you connect
other cameras you will first have to assign them an IP address suitable for the NVR's internal network.
You cannot connect other network devices, such as switches or routers, to these ports.
DSE SRL – ITALY – WWW.DSE.EU
INSTALLATION MANUAL
RK SERIES – DVR and NVR GUI 6.0
Page:10
DC 12V–Connect the included 12VDC power supply here
DSE SRL – ITALY – WWW.DSE.EU
Autres manuels pour RK Series
8
Table des matières
Autres manuels DSE DVR
DSE
DSE DK-PV500W Manuel utilisateur
DSE
DSE DX Series Feuille d'instructions
DSE
DSE DR-N8 Manuel utilisateur
DSE
DSE DR-N16 Manuel utilisateur
DSE
DSE DK-CS4-HDS Manuel utilisateur
DSE
DSE RK Series Feuille d'instructions
DSE
DSE DK-CS4-DVR Manuel utilisateur
DSE
DSE DH Series Manuel utilisateur
DSE
DSE G1680 Manuel utilisateur
DSE
DSE DK-PV500LW Manuel utilisateur
