Drayton RF710 Mode d’emploi
Digistat+1 & Digistat+1RF
Room Thermostat
Models:
RF710/22190/22192
Invensys Controls Europe
Technical Helpline: +44 (0) 845 130 7722
www.draytoncontrols.co.uk
)NSTALLATION'UIDE2&02/$5#4/.,9).34!,,!4)/./&3#22&-ODELSONLYIf you do not have the knowledge to install the SCR safely then you
must arrange for a competent electrician to install it for you. Wiring
must conform to the current IEE wiring regulations.
Prior to commencing the installation you must ensure the mains
supply is switched off.
)NSTALLATION)NSTRUCTIONS2EADALLINSTALLATIONANDCOMMISSIONINGINSTRUCTIONSBEFOREPROCEEDING$ONOTSWITCHONUNTILREADYTOCOMMISSIONThe system wiring must be able to be fully disconnected from the
mains supply by a switch incorporated in the fixed wiring having a
contact separation of at least 3mm on both poles. Fused at 3A.
On
Receive / Alarm
Override 2
1
Learn
Mode
Digistat SCR
Wireless System
,OCATIONThe Digistat SCR (receiver) should be mounted in a convenient
position, close to the boiler or central heating system wiring centre.
(Care should be taken not to mount the SCR in a position where it
is surrounded by metal objects or mains voltage cable, as this may
interfere with the radio signal).
For the best performance install in an open space, at least 30cm
distance from any metal objects including wall boxes and boiler
housing.
It is recommended that the SCR is mounted on the wall nearest the
final location of the Digistat +RF room thermostat and not less than
30cm from the boiler side panel.
7ARNING)NSTALLINGTHE3#2TOOCLOSETOTHEMETALSIDEPANELORMAINSCABLESMAYINTERFEREWITHTHERADIOSIGNAL
&IXINGMINIMUMWALLPLATECLEARANCESSHOWN1. Loosen the securing screws, remove the wallplate, and if surface
wiring is to be used, snap out the cable entry strip on the bottom
edge of the wallplate with a pair of pliers.
2. Fix the wallplate, terminals at the top, either direct onto the flat
wall using wall plugs and no 6 x1” wood screws or on a flush
mounting single conduit box using M3.5 x 14 screws. Minimum
wallplate clearances are shown.
3. Complete the wiring to the SCR wallplate in accordance with the
relevant diagram, to comply with current IEE wiring regulations.
4. Place the SCR onto the wallplate and tighten the securing screws.
BOILER
30cm Min
Preferred side of boiler
The range may be affected by
composition/density and number of walls
between the Digistat +RF and SCR
Radio Signal Range:
30m Typically
SCR
NL1234
50 mm
minimum
clearance
40 mm
minimum
clearance
40 mm
minimum
clearance
70 mm
minimum
clearance
NL 1 2 3
230V a.c.
Fused 3A
Common Heating
satisfied
or call for
cooling
Call for
heat
Volt free contacts
3#2WALLPLATECLEARANCES%LECTRICALThis product is double insulated and does not require an earth connection.
The SCR should be wired to the combi boiler or central heating wiring using
the correct type of cable or flex. The SCR should be wired in to replace
hard wired room or programmable thermostats shown on the system or
boiler wiring diagrams. Always check other manufacturers instructions for
compatibility.
#OMBIBOILERBASICWIRINGLAYOUT:ONECONTROLBASICWIRINGLAYOUT#/--)33)/.).'4(%j7)2%,%333934%-k2&-ODELSONLYStandard for all models
IMPORTANT: MULTIZONE INSTALLATIONS ONLY
If more than one ‘wireless system’ is fitted within the same property.
ie. for controlling 2 or more zones (multi-zone) it is essential that the
Digistat RF units are matched correctly to the relevant SCR. This is easily
achieved by commissioning each Digistat and SCR in turn.
1. Install (see installation instructions) and turn power on to the
SCR (receiver). If a separate programmer is fitted, ensure that it is
switched on. The red LED should come on.
2. Push the ‘override’ button on the SCR once. The green LED should
also come on. Check to see if the boiler and/or motorised valve
are working.
3. To enter ‘learn’ mode push the button marked 1 followed by 2
(OVERRIDE) and hold both depressed together. The red LED
should flash for 2 seconds and then go out signifying the SCR is in
learn mode. Release both buttons.
4. The red and green LED’s should both now be on.
5
NL123
SCR
L -
N -
Digistat + RF
Radio signals
to SCR - no wiring
Switched
230V a.c.
fused 3A,
Internal
boiler
electronics
External
controls
connections
NL123
L
SCR
Switched live
from wiring
centre Motorised valve
N
To boiler
and/or
pump
Radio signals
to SCR - no wiring
230V a.c.
fused 3A
Digistat + RF
5. Take the Digistat RF and hold it within sight of the SCR (no closer
than one metre).
6. Remove the battery cover and fit the batteries.
7. The Digistat RF should now display the actual room temperature.
If the unit has been stored in a cold place, it may take time to warm
up.
8. As soon as the batteries are fitted, the red LED on the SCR should
flash for 7 seconds and then go out.
The green LED may be on or off depending on the room temperature
at the time of commissioning.
9. If the red LED remains on, remove the batteries on the Digistat RF,
check the battery positions are correct, and once the display has
faded, repeat steps 6 to 8.
10. Increase the ‘SET’ temperature on the Digistat RF by pressing the
+ button until a flame symbol appears, in the left hand segment of
the display.
11. The red LED on the SCR should flash for 7 seconds. This confirms
that the radio signal is being sent and received. After 7 seconds the
red LED should go out and the green one come on.
12. Check to confirm that the boiler and/or motorised valves are
working.
13. Decrease the ‘SET’ temperature on the Digistat RF by pressing the
- button until the flame symbol disappears.
14. The red LED on the SCR should flash for 7 seconds. After 7 seconds
both the red and green LEDs should go out. Check that the boiler
and/or motorised valve have powered down.
15. Place the Digistat RF in the chosen operating position, (see Digistat
RF location section) and repeat steps 10 to 14. Once you have
confirmed the system operates correctly, fit and secure the Digistat RF
to the wall (see installation instructions).
During normal operation the red LED on the SCR will flash for 7 seconds
each time a radio signal is received from the Digistat RF. This will occur
approximately every 5 minutes.
The green LED on the SCR denotes a call for heat (ON).
/NCETHESYSTEMHASBEENSUCCESSFULLYCOMMISSIONEDBUTTONSANDONTHE3#2SHOULDNOTBEPRESSEDSIMULTANEOUSLYUNLESSAREPLACEMENT$IGISTAT2&OR3#2ISØTTED
,OCATIONRoom Thermostat
1.5m
Care should be taken to mount the thermostat in a position which is not
subject to direct sunlight or draughts. Preferably it should be mounted
on an inside wall about 1.5m (5ft) above the floor in a position where it
can respond to room temperature but away from the direct influence of
radiators or other appliances giving off heat.
3IGNAL3TRENGTH2&-ODELSBefore fixing the Digistat+RF to the wall it is recommended to first check
the signal strength from that location.
To do this, remove the batteries, press and hold the ‘+’ button whilst
refitting the batteries, the display will show ‘rF’ which indicates that the
Digistat+RF is continuously sending an OFF signal to the SCR (receiver).
Leave the Digistat+RF in position and return to view the SCR. If the red
LED is continuously flashing, this indicates a good signal. If the red LED is
not flashing, this indicates a poor signal and you need to reposition the
Digistat+RF until the red LED is flashing.
When the signal strength has been confirmed remove the batteries to
cancel the test and follow the installation instructions.
"EFORE)NSTALLATIONIf you do not have the knowledge to install the thermostat safely then
you must arrange for a competent electrician to install it for you. Wiring
must conform to the current IEE regulations.
Prior to commencing the installation you must ensure the mains supply is
switched off.
1. Remove the front cover using a flat screwdriver and separate from
back plate (Fig 1).
2. Fix the back plate directly onto the wall using suitable wall plugs and
screws or mount over existing wall box (Fig 2).
(Fig 1)
(Fig 2)
(Fig 3)
3. Replace the front cover by locating in position and pushing fully onto
the back cover (Fig 3).
Drayton
Drayton
4. Remove the battery cover using a coin (Fig 4).
5. Install the 2 AA batteries provided (Fig 5).
6. Replace battery cover (fig 6).
7. The Digistat +1RF is now installed and will automatically start to control the
room temperature.
Drayto
n
Drayto
n
Drayto
n
Drayto
n
(Fig 4)
(Fig 6)
(Fig 5)
7)2).'.OT2&-ODELS
%LECTRIC(EAT
Combi Boiler
"ASIC"OILERWITH:ONE6ALVE
&!5,4$)!'./3)3!LL-ODELS)FTHEDISPLAYSHOWS%THEFOLLOWINGFAULTSCOULDHAVEOCCURRED1.Internal temperature sensor has failed.
2. Ambient temperature is outside product operating temperature range.
3"ASIC"OILER
Technical Data
$)')34!4$)')34!42&2//-5.)40OWER3UPPLY2 x AA Size, 1.5V alkaline batteries
3WITCH4YPE2ATING2ELAYVERSIONSPDT 16(2)A 230V a.c. Volt free
-INRECOMMENDEDCURRENT10mA@24V a.c. (inductive)
2ADIOFREQUENCY2&VERSION433 MHz
Radio Signal Range: 30m typically. The range may be affected by
2&6ERSIONthe composition / density and number of
walls between the Digistat RF and SCR.
Temperature Range: 5 to 30ºC
#ONTROL!CCURACY+ 0.5K @ 20ºC
!MBIENT4EMPERATUREOperating 0ºC to 40ºC /
Storage –20ºC to 55ºC
Mounting: Suitable for surface or conduit box
mounting
Wiring:
Relay: Designed for fixed wiring only, to comply
with current IEE wiring regulations (BS7671).
2&No wiring required
"ALL0RESSURE4EST75ºC
0OLLUTION$EGREE2
Autres manuels pour RF710
1
Ce manuel convient aux modèles suivants
6
Table des matières
Autres manuels Drayton Thermostat
Drayton
Drayton MiStat P710R Manuel utilisateur
Drayton
Drayton Digistat+ 2 22084 Manuel d'utilisation
Drayton
Drayton Combi-Stat RTS8 Guide de configuration
Drayton
Drayton Combi-Stat RTS8 Manuel utilisateur
Drayton
Drayton MiStat N110R Manuel utilisateur
Drayton
Drayton 22084 Manuel utilisateur
Drayton
Drayton Digistat +2 Manuel utilisateur
Drayton
Drayton Digistat+2 22084 Manuel utilisateur
Drayton
Drayton 22083 Manuel utilisateur
Drayton
Drayton 13616 Manuel utilisateur
Drayton
Drayton MiStat P710R Manuel utilisateur
Drayton
Drayton RF701 Manuel utilisateur
Drayton
Drayton MiStat C C110C Instructions de montage
Drayton
Drayton 30002 Manuel utilisateur
Drayton
Drayton Digistat +3 22083 Manuel utilisateur
Drayton
Drayton Digistat+3 22083 Manuel utilisateur
Drayton
Drayton Digistat 1 Manuel utilisateur
Drayton
Drayton Digistat RF3 Manuel utilisateur
Drayton
Drayton Digistat 2 Manuel utilisateur
Drayton
Drayton Wiser Thermostat Kit 1 Manuel utilisateur
Manuels Thermostat populaires d'autres marques
EWELLY
EWELLY EW-181 Manuel utilisateur
Prolon
Prolon T1100 Instructions d'installation
Computherm
Computherm Q20 Manuel utilisateur
Heatmiser
Heatmiser neoStat Manuel utilisateur
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur
