Drayton 13616 Manuel utilisateur

Models:

13616/13618/13619

Models:

13616/13618/13619

Default Settings

The maximum and minimum setpoints are preset in the factory to

65oC and 60oC respectively.

06490084001 ISS H 06490084001 ISS H

Simple Setting or Operating

To set the required temperature

•The display normally shows the current setpoint.

•To adjust the required temperature, turn the

dial clockwise to increase or anti-clockwise to

decrease, (1 click = 5ºC), the LCD will display

the temperature setpoint as it is being

adjusted and ‘SET’ will be displayed. After a

few seconds the display will return

to normal

operation and will display the current setpoint.

DHW Cylinder Thermostat

To assist with commissioning or checking the system operation,

there is a positive OFF setting outside the temperature scale on the

cylinder thermostat. First adjust the minimum temperature setting

to 40oC as described in the user guide, then rotate the dial fully

anticlockwise for OFF.

‘Boost 1 Hr’

Digistat+C RF

Digistat+C RF should now display the ‘E2’ and the RF symbol ‘ ’. If

Digistat+C RF

the

Digistat+C RF transmitter unit and sensor can be installed.

When the sensor is wired to the transmitter unit, the display will

change after approx. 30 seconds to show the current setpoint and

‘E2’ will disappear

Digistat+C RF

Boost 1 Hr

BOILER

30cm Min

Preferred side of boiler

The range may be affected by

composition/density and number of walls

between the Digistat +CRF and SCR

230V a.c.

Digistat+C RF

Heating

Radio Signal Range:

30m Typically

SCR

Technical Helpline: +44 (0) 845 130 7722

www.draytoncontrols.co.uk

Email: [email protected]

Digistat +CRF Digistat +CRF

RECEIVE / ALARM

OVERRIDE

LEARN

MODE

Wireless System

Digistat +C SCR

Technical Helpline: +44 (0) 845 130 7722

www.draytoncontrols.co.uk

Email: [email protected]

The hot water can be manually switched on and off by using the

‘Boost 1 Hr’ button on the SCR in a fault situation, even though

the red LED will stay on until a satisfactory signal is reinstated.

When the hot water is turned on by pressing the ‘Boost 1 Hr’

button, it will time out after 1 hour and return to OFF.

the Digistat+C RF unit.

the Digistat+C RF unit are

the Digistat+C RF

Proper Battery Recycling

Electronic devices and batteries, rechargeable or not, should not be

disposed of into ordinary household waste. Instead, they must be

recycled properly to protect the environment and cut down the waste

of precious resources. Your local waste management authority can

supply details concerning the proper disposal of batteries.

In compliance with the EU Directive 2006/66/EC, the button cell

battery located on the printed circuit board inside this product, can be

removed at the end of product life, by professional personnel only.

Unclip the housing to show the terminal block. First, connect a 2-core

cable to the Digistat+C RF transmitter, cut to the required length to

reach the sensor position. Connect to the sensor in the position shown

and fold wires back through the cable grip & out through the cable

entry, re-assemble the housing.

Signal Strength

Before fixing the Digistat+C RF to the wall it is recommended to first

check the signal strength from that location.

To do this, remove the batteries, press and hold the ‘set’ button whilst

refitting the batteries, keep the ‘set’ button held and after a few

seconds the display will show ‘rF’ which indicates that the Digistat+C RF

is continuously sending an OFF signal to the SCR (receiver). Leave the

Digistat+C RF in position and return to view the SCR. If the red LED is

continuously flashing, this indicates a good signal. If the red LED is not

flashing, this indicates a poor signal and you need to reposition the

Digistat+C RF until the red LED is flashing.

When the signal strength has been confirmed remove the batteries to

cancel the test and follow the installation instructions.

Relevant EC Directives:

Applied Standards:

230V a.c.

of walls between the Digistat +C RF and SCR.

+0/-8

230V a.c.

24V a.c./d.c.

(BS7671).

2006/95/EC Low Voltage Directive

2004/108/EC Electromagnetic Compatibility

Directive

1999/5/EC R&TTE Directive

2006/66/EC Battery Directive

EN60730-1; EN60730-2-9

ETSI EN 300 220-3, ETSI EN 301 489-3

2011/65/EU RoHS Directive

Temperature Range: 40°C to 70°C

Industry Standard Wallplate

2.5Kv

75°C

Mounting:

Pollution Degree:

Software Class:

Pollution Degree:

Software Class:

Rated Impulse Voltage:

Ball Pressure Test:

Energy Class: I = 1% (According to EU 811/2013,

812/2013, 813/2013, 814/2013)

Autres manuels pour 13616

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Drayton Thermostat

Drayton

Drayton Digistat+3 22083 Manuel utilisateur

Drayton

Drayton RF710 Manuel utilisateur

Drayton

Drayton RTS1 Manuel utilisateur

Drayton

Drayton LP10RF Manuel d'utilisation

Drayton

Drayton RF701 Manuel utilisateur

Drayton

Drayton Digistat +3 22083 Manuel utilisateur

Drayton

Drayton Digistat 2 Manuel utilisateur

Drayton

Drayton RF710 Mode d’emploi

Drayton

Drayton Combi-Stat RTS8 Guide de configuration

Drayton

Drayton Digistat +2 Manuel utilisateur

Drayton

Drayton Digistat RF3 Manuel utilisateur

Drayton

Drayton RF701 Manuel utilisateur

Drayton

Drayton Digistat+ 2 22084 Manuel d'utilisation

Drayton

Drayton MiStat P710R Manuel utilisateur

Drayton

Drayton 22083 Manuel utilisateur

Drayton

Drayton Lifestyle Mode d’emploi

Drayton

Drayton RF701/22092 Manuel utilisateur

Drayton

Drayton LP10RF Manuel d'utilisation

Drayton

Drayton Wiser Manuel utilisateur

Drayton

Drayton Combi-Stat RTS8 Manuel utilisateur

Drayton

Drayton MiStat N110R Manuel utilisateur

Drayton

Drayton Digistat+1 RF710 Manuel utilisateur

Drayton

Drayton Wiser Thermostat Kit 1 Manuel utilisateur

Drayton

Drayton LP10RF Manuel d'utilisation

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Honeywell

Honeywell CM721 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

Honeywell

Honeywell RLV4305 Manuel utilisateur

Honeywell

Honeywell Prestige 2.0 THX9421 Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur