Drayton HTS3 Manuel utilisateur

Customer Service Tel: 0845 130 5522

Customer Service Fax: 0845 130 0622

Technical Helpline Tel: 0845 130 7722

Website: www.draytoncontrols.co.uk

Email: [email protected]

090-728 ISSD

HTS3 Cylinder

Thermostat

Installation instructions

Technical Data

Setting Range 50° – 80°C

Differential 8°C approx.

Switch rating 3 (1) A 230V ac

Switch type SPDT

Earth Double insulated

– not required

Connections C – common

1 – call

2 – satisﬁed

Fixing Plastic-coated spring wire

with hook and eyelet.

Conforms to the essential

requirements of the following directives:

2004/108/EC – Electromagnetic compatibility

Directive

2006/95/EC – Low Voltage Directive

Cylinder thermostats

Make Model Common Call Satisﬁed

HTS 3 C 1 2

Lifestyle HTS 2 R B Y

Danfoss

Randall AT (CN4) 1 2 3

Drayton CS 1/CS 2 1 2 3

Honeywell L641A C 1 2

Landis

& Gyr RAM 1 1 2 3

Potterton

Myson PTT 1 L H C

Sunvic 1452/

SA2451 3 1 2

Sopac SAY C 1 2

Smiths SCT 1 1 2 3

Tower CS 1 R B Y

Barlo CT 1 R B Y

Pollution Degree

Ball pressure

Test Temperature

110ºC

Rated impulse

voltage

2.5kV

2011/65/EU – Restriction of the Use of Certain

Hazardous Substances (RoHS)

Energy Class I = 1% (Acc. EU

811/2013, 812/2013,

813/2013, 814/2013)

Positioning the HTS3

The HTS3 should be installed approximately one

third of the way up the hot water cylinder, and at

the front for ease of access.With pre-insulated

cylinders, mark the position and size, and remove

just enough insulation to allow the HTS3 to ﬁt

against the metal of the cylinder in the recess

formed.

Wiring Connections

From the wiring centre or junction box, run

sufﬁcient 3-core electrical connecting cable to

reach the HTS3 installation position without being

under tension.

Remove the HTS3 cover by undoing the

central retaining screw. Make wiring connections in

accordance with the diagram below and the

manufacturers instructions for associated

equipment such as motorised valves, boiler,

programmers etc. Replace and secure the cover.

The HTS3 is double insulated and no Earth

connection is necessary. The circuit should be

protected with a 3A fuse.

Fixing to the Cylinder

The base of the HTS3 should be held in good

contact with the metal of the hot water cylinder.

The plastic covered spring ﬁxing cable should

be cut to an unstretched length of

approximately 2 1/2” – 3” less than the

circumference of the cylinder and the hook and

eyelet screwed into the ends. Stretch the cable

round the cylinder, above the insulation, and

position it in the groove across the front of the

HTS3. Engage the hook and eyelet.

Common

heat

Satisfied

Cylinder

Insulation

Fixing cable

HTS3

cylinder

HTS3

height

Commissioning

The two setting marks outside the

temperature scale on the HTS3 provide max

temperature and OFF positions to assist with

commissioning or checking the system

operation. Rotate the setting arrow fully max

and anticlockwise for OFF.

Setting

With a screwdriver, position the setting arrow

at the desired nominal hot water temperature.

A popular setting is 60°C but if this is not

exactly suitable, simply adjust up or down as

appropriate.

WARNING

Disconnect mains supply before

ﬁtting or removing the cover.

A switch having contact

separation of at least 3mm in all

poles must be incorporated in the

ﬁxed wiring as a means of providing

full disconnection of the mains

supply.

Table des matières

Autres manuels Drayton Thermostat

Drayton

Drayton Lifestyle Mode d’emploi

Drayton

Drayton MiStat N110R Manuel utilisateur

Drayton

Drayton Combi-Stat RTS8 Manuel utilisateur

Drayton

Drayton Digistat+ 2 22084 Manuel utilisateur

Drayton

Drayton Digistat RF3 Manuel utilisateur

Drayton

Drayton 30002 Manuel utilisateur

Drayton

Drayton MiStat C C110C Instructions de montage

Drayton

Drayton LP10RF Manuel d'utilisation

Drayton

Drayton Digistat+ 2 22084 Manuel d'utilisation

Drayton

Drayton Wiser Thermostat Kit 1 Manuel utilisateur

Drayton

Drayton Digistat RF3 Manuel utilisateur

Drayton

Drayton Digistat +3 22083 Manuel utilisateur

Drayton

Drayton Digistat +2 Manuel utilisateur

Drayton

Drayton MiTime T720R Manuel utilisateur

Drayton

Drayton LP722 Manuel utilisateur

Drayton

Drayton MiStat P710R Manuel utilisateur

Drayton

Drayton RF701/22092 Manuel utilisateur

Drayton

Drayton Lifestyle LP111Si Manuel utilisateur

Drayton

Drayton RF710 Mode d’emploi

Drayton

Drayton LP10RF Manuel d'utilisation

Drayton

Drayton MiStat P710R Manuel utilisateur

Drayton

Drayton 22084 Manuel utilisateur

Drayton

Drayton RF701 Manuel utilisateur

Drayton

Drayton 13616 Manuel utilisateur

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Honeywell

Honeywell CM721 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

Honeywell

Honeywell RLV4305 Manuel utilisateur

Honeywell

Honeywell Prestige 2.0 THX9421 Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur