Dimplex VCX1525 Manuel utilisateur

Owner’s Manual

Model

VCX1525

VCX1525-WH

To view the full line of Dimplex products, please visit

www.dimplex.com

7209350100R04

IMPORTANT SAFETY INFORMATION: Always read this manual rst

before attempting to install or use this replace. For your safety, always

comply with all warnings and safety instructions contained in this manual

to prevent personal injury or property damage.

2 www.dimplex.com

Table of Contents

Always use a qualied technician

or service agency to repair this

replace.

!NOTE: Procedures and

techniques that are

considered important

enough to emphasize.

CAUTION: Procedures

and techniques which, if not

carefully followed, will result in

damage to the equipment.

WARNING: Procedures

and techniques which, if not

carefully followed, will expose

the user to the risk of re,

serious injury, or death.

Welcome & Congratulations . . . . . . . . . . . . . . . . .3

IMPORTANT INSTRUCTIONS . . . . . . . . . . . . . . .4

Quick Reference Guide . . . . . . . . . . . . . . . . . . . . .7

Fireplace Installation .......................7

Operation...............................14

Maintenance.............................16

Warranty ...............................18

ReplacementParts........................20

Welcome & Congratulations

Thank you and congratulations for choosing to purchase an electric

replace from Dimplex, the world leader in electric replaces.

Please carefully read and save these instructions.

CAUTION: Read all instructions and warnings carefully before

starting installation. Failure to follow these instructions may result

in a possible electric shock, re hazard and will void the warranty.

Please record your model and serial numbers below for future

reference: model and serial numbers can be found on the model and

serial number labels of your replace.

Model Number

Plate

NO NEED TO RETURN TO THE STORE

Questions with operation or assembly? Require Parts Information?

Product Under Manufacturer’s Warranty?

For Troubleshooting and Technical Support

OR Toll-Free 1-888-DIMPLEX (1-888-346-7539)

Monday to Friday 8:00 a.m. to 4:30 p.m. EST

Please have your model number and product serial

number ready. (See above)

4 www.dimplex.com

When using electrical appliances,

basic precautions should always

be followed to reduce the risk of

fire, electric shock, and injury to

persons, including the following:

①Read all instructions before

using the Convex In-Stud

replace.

②The heater is hot when in use.

To avoid burns, do not let bare

skin touch hot surfaces. The trim

around the heater outlet becomes

hot during heater operation.

Keep combustible materials, such

as furniture, pillows, bedding,

papers, clothes, and curtains at

least three (3) feet (0.9 m) from

the front of the unit.

③ Extreme caution is necessary

when any heater is used by or near

children and whenever the unit is

left operating and unattended.

④Always disconnect power to

the replace when not in use for

extended period of time.

⑤Do not operate with a

damaged cord or plug (for units

supplied with a cord), or if the

heater has malfunctioned, or if

the replace has been dropped or

damaged in any manner. Contact

Dimplex Customer Services at

1-888-346-7539 immediately.

IMPORTANT INSTRUCTIONS

⑥Do not use outdoors.

⑦Never locate heater where it

may fall into a bathtub or other

water container.

⑧Do not run the cord under

carpeting (for units supplied with

a cord). Do not cover cord with

throw rugs, runners, or the like.

Arrange cord away from trafc

area and where it will not be

tripped over.

⑨To disconnect the unit, turn

the controls off, and then remove

the plug from the outlet or switch

off at main power supply panel if

the unit is hard wired.

⑩Do not insert or allow foreign

objects to enter any ventilation

or exhaust opening as this may

cause an electric shock or re, or

damage to the heater.

⑪ To prevent a possible re, do

not block air intake or exhaust in

any manner.

⑫All electrical heaters have

hot and arcing or sparking parts

inside. Do not use in areas where

gasoline, paint, or ammable

liquids are used or stored or

where the unit will be exposed to

ammable vapors.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER-SERVICEABLE PARTS INSIDE

SAVE THESE INSTRUCTIONS

IMPORTANT INSTRUCTIONS

⑬ Do not modify the replace.

Use it only as described in this

manual. Any other use not

recommended by the manufacturer

may cause re, electric shock or

injury to persons.

⑭This unit may have a

polarized plug (one blade is wider

than the other). The plug will t in

a polarized outlet only one way.

If the plug does not t fully in the

outlet, reverse the plug. If it still

does not t, contact a qualied

electrician to install the proper

outlet.

⑮ Do not change the plug in

any way. Avoid the use of an

extension cord. Extension cords

may overheat and cause a risk of

re. If you must use an extension

cord, the cord must be No. 14

AWG minimum size and rated no

less than 1875 Watts.

⑯Do not burn wood or other

materials in the replace.

⑰Do not strike the glass front.

⑱ Always use a certied

electrician for build-in hard-wired

installation.

⑲Always use properly

grounded, fused and polarized

outlets.

⑳Disconnect all main power

supply (unplug the unit or switch

off at main service panel) before

performing any cleaning,

maintenance or relocation of the

unit.

21 Do not operate the replace

without the glass assembly and/or

frame.

22 When transporting or storing

the unit and cord, keep in a dry

place, free from excessive

vibration and store so as to avoid

damage.

23 Do not put combustible

material, liquid, or small articles

such as sand inside glass

assembly.

6 www.dimplex.com

IMPORTANT INSTRUCTIONS

WARNING: Remote control

contains small batteries. Keep away

from children. If swallowed, seek

medical attention immediately.

WARNING: Do not install battery

backwards, charge, put in re or mix

with used or other battery types - may

explode or leak causing injury.

!NOTE: Changes or modications

not expressly approved by the party

responsible for compliance could

void user's authority to operate the

equipment.

CAUTION: This equipment has

been tested and found to comply with

the limits for Class B digital device,

pursuant to part 15 of the FCC

Rules. These limits are designed to

provide reasonable protection against

harmful interference in a residential

installation. This equipment

generates, uses and can radiate

radio frequency energy and, if not

installed and used in accordance with

the instructions, may cause harmful

interference to radio or television

reception, which can be determined

by turning the equipment off and

on, the user is encouraged to try to

correct the interference by one or

more of the following measures:

Reorient or relocate the receiving•

antenna.

Increase the separation between•

the equipment and the receiver.

Connect the equipment into an•

outlet on a circuit different from

that to which the receiver is

connected.

Consult the dealer or an•

experienced radio/TV technician

for help.

Operation is subject to the following

two conditions: (1) this device may

not cause interference and (2) this

device must accept any interference,

including interference that may cause

undesired operation of the device.

Fireplace Installation

!NOTE: A 15 Amp, 120

Volt circuit is required. A

dedicated circuit is preferred

but not essential in all cases.

A dedicated circuit will be

required if, after installation,

the circuit breaker trips or the

fuse blows on a regular basis

when the heater is operating.

Additional appliances on the

same circuit may exceed the

current rating of the circuit

breaker.

WARNING: Ensure the

power cord is not installed so

that it is pinched or against a

sharp edge and ensure that

the power cord is stored or

secured to avoid tripping or

snagging to reduce the risk of

re, electric shock or injury to

persons.

Construction and electrical

outlet wiring must comply

with local building codes and

other applicable regulations to

reduce the risk of re, electric

shock and injury to persons.

Do not attempt to wire your

own new outlets or circuits. To

reduce the risk of re, electric

shock or injury to persons,

always use a licensed

electrician.

Quick Reference Guide

① Before using the In-Stud

replace verify:

• Are the circuit breakers for the

unit on?

• Are the light bulbs loose? (to

check, follow the instructions

for replacing the light bulbs

under the maintenance section

of this manual)

②The heater may emit a slight,

harmless odor when rst used.

This odor is a normal condition

caused by the initial heating of

internal heater parts.

③The information regarding the

model of your unit can be found

on the model and serial number

plate located on the side of the

unit. See Page 3 for an illustration

on how to locate the rating plate.

8 www.dimplex.com

WARNING: The Convex

In Stud replace is wall

mountable and can be built in

a wall space 16 inches (406

mm) over-center between 2”

x 4” wall studs. Follow the

installation instructions for

either wall mount or built-in

mounting; failure to do so may

cause damage or injury.

Wall Mounting Instructions

Leave the glass assembly 1.

uninstalled until step 10.

Select a location for the2.

replace, preferably above

an electrical outlet and there

must be at least one wall stud

behind for the replace to

mount onto. The bottom of

the unit must be a minimum

of 14" (356 mm) above the

oor (mounting holes 29¾"

(0.75 m) minimum above the

oor) (Figure 2).

Access to the electrical outlet

must be maintained. Ensure the

installation meets the national and

state/provincial electrical codes.

!NOTE: It is recommended

that the bottom of the unit not be

mounted higher than 48" (1.22

m) from the ground to maintain

an optimized viewing angle of the

Fireplace Installation

ame.

CAUTION: The replace must

be mounted at two (2) points, one

of which must be on a wall stud.

WARNING: High tempera-

tures may be generated under

certain abnormal conditions. Do

not partially or fully cover or ob-

struct the bottom of this heater.

Bottom of unit must be a mini-

mum of 14" (356 mm) above the

oor or any surface such as a ta-

bletop to ensure adequate space

Figure 2

ABC D E F G

29¾” - 75¾”

(0.75 - 1.92m)

14” - 48”

(0.36 - 1.22m)

Fireplace Installation

for heat exhaust from the bottom

of the replace (Figure 3).

With a wall stud nder, locate 3.

the center of the wall stud,

drive a wood screw into the

stud and leave approximately

⅛" (3 mm) exposed threads

for the replace to hang on.

The second mounting point4.

should be picked such that it

is farthest (to the left or right)

relative to the rst one among

the seven (7) keyholes (A to

G shown in Figure 2) on the

replace for wall mounting,

these keyholes are 2" (51

mm) apart. For example, if

you plan to use hole B as

the rst mounting hole, the

second mounting hole must

Figure 3

Heat Exhaust

be G.

Other available combinations

are A-G, C-G, A-F, A-E, A-D

and D-G.

Mark the second mounting5.

screw location; ensure that it

is level with the rst with the

help of the provided bubble

level and the replace itself.

Screw the threaded drywall

anchor in the drywall with a

Philip’s head screwdriver until

the head is at against the

wall surface.

Caution should be taken

when using a power tool to

install a threaded drywall

anchor as the drywall may

distort, tear or slightly buckle

as a result of over-torque.

With a Philip’s head screw6.

driver, screw the drywall

anchor screw into the drywall

anchor already in the wall,

leave ⅛" (3 mm) exposed

threads for mounting the

replace.

With the glass assembly7.

taken off, mount the rebox

onto the two (2) mounting

screws.

Mark position of hole “H”.8.

Remove replace from wall.9.

10 www.dimplex.com

Install drywall anchor into10.

drywall at marked position.

With the glass assembly off,11.

mount the replace onto the

two (2) mounted screws.

Tighten both mounting screws12.

with a screwdriver. Be

careful not to over tighten the

screws mated with the drywall

anchor.

Secure Philip’s screw into13.

drywall anchor, already in the

wall (H).

Open the bag of pebbles14.

and gently pour through

top opening of front glass

assembly.

Fireplace Installation

Install glass assembly as15.

shown in Figure 4.

Built-In Instructions

WARNING: The installation

of the replace unit must

comply with the applicable

local and/or national electrical

codes and utility requirements.

This installation should be

entrusted to duly qualied

personnel where required by

law.

Leave the frame uninstalled 1.

from the replace chassis

until step 13.

Prepare a wall opening2.

Ensure Glass

Assembly

brackets engage

hooks on replace

by sliding Glass

Assembly towards

replace and then

down Secure Glass

Assembly with the

four (4) supplied

self-tapping screws

Figure 4

Autres manuels pour VCX1525

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Dimplex Cheminée intérieure

Dimplex

Dimplex Piccolo PCO20 Manuel utilisateur

Dimplex

Dimplex EF3003 Manuel utilisateur

Dimplex

Dimplex DF2426 Manuel utilisateur

Dimplex

Dimplex BLF7451 Manuel utilisateur

Dimplex

Dimplex BF8000ST Manuel utilisateur

Dimplex

Dimplex DF3033ST Manuel utilisateur

Dimplex

Dimplex VEGA Manuel utilisateur

Dimplex

Dimplex BF8000ST Manuel utilisateur

Dimplex

Dimplex PF2325 Manuel utilisateur

Dimplex

Dimplex CAS1000M Manuel utilisateur

Dimplex

Dimplex CHERITON LOG Manuel utilisateur

Dimplex

Dimplex DF2608 Manuel utilisateur

Dimplex

Dimplex Pro Series Manuel utilisateur

Dimplex

Dimplex DFI2309 Guide de démarrage rapide

Dimplex

Dimplex SF55992-AU Guide de démarrage rapide

Dimplex

Dimplex Cassette L Pebble Manuel utilisateur

Dimplex

Dimplex Revillusion Haydn Manuel utilisateur

Dimplex

Dimplex Juneau JUN Manuel utilisateur

Dimplex

Dimplex VCX1525-EU Manuel utilisateur

Dimplex

Dimplex MULTIFIRE DF3215 Manuel utilisateur

Dimplex

Dimplex Toluca Deluxe Manuel utilisateur

Dimplex

Dimplex DFI400L Manuel utilisateur

Dimplex

Dimplex BF45DXP Manuel utilisateur

Dimplex

Dimplex ELECTRALOG CFP3913 Manuel utilisateur

Manuels Cheminée intérieure populaires d'autres marques

Brigantia

Brigantia 35-DVRS31N-2 Manuel du propriétaire

Nordpeis

Nordpeis Bergen Manuel utilisateur

Superior

Superior BCT2536TMN Manuel utilisateur

Quadra-Fire

Quadra-Fire 5100I-GD-B Manuel utilisateur

Renaissance

Renaissance RUMFORD 1000 Manuel utilisateur

Lacunza

Lacunza IV-800 Manuel utilisateur

Baxi

Baxi 940 Instructions d'utilisation

Dru

Dru Maestro 60/2 Tall RCH Manuel utilisateur

Diamond Fireglass

Diamond Fireglass SS-O22 Manuel utilisateur

HearthStone

HearthStone Windsor Bay 8830 Manuel de programmation

Napoleon

Napoleon ASCENT B42 Manuel utilisateur

Enviro

Enviro E33GI Manuel utilisateur

Smeg

Smeg L30 FABE Instructions de montage

KEDDY

KEDDY K700 Manuel utilisateur

Godin

Godin 3451 Manuel utilisateur

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manuel utilisateur

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manuel utilisateur

Desa

Desa CCFPDFT Manuel d'utilisation