Dimplex SF55992-AU Guide de démarrage rapide

26” FIREPLACE

MODEL NUMBER

SF55992-AU

PARTS AND SERVICE MANUAL

TABLE OF CONTENTS

OPERATION PAGE 1

PARTS DRAWING PAGE 3

PARTS LIST PAGE 4

WIRING SCHEMATIC PAGE 6

LIGHT BULB REPLACEMENT PAGE 10

MAIN POWER ON/OFF SWITCH REPLACEMENT PAGE 12

LIGHT DIMMER SWITCH REPLACEMENT PAGE 13

FLAME SPEED CONTROL REPLACEMENT PAGE 14

FLAME MOTOR/FLAME ROD REPLACEMENT PAGE 15

HEATER ON/OFF SWITCH REPLACEMENT PAGE 16

HEATER THERMOSTAT CONTROL REPLACEMENT PAGE 17

HEATER ASSEMBLY REPLACEMENT PAGE 18

POWER CORD REPLACEMENT PAGE 19

OPERATION

This section will explain the function of each convenient control.

To access the controls, open the upper grill by pulling, near the top right hand side,

forward and down.

A. MAIN ON/OFF SWITCH

The ON/OFF SWITCH supplies power to all fireplace functions (Heater/Flame).

B. FLAME ACTION CONTROL

Turn the flame action control knob to adjust the flame speed to the desired level.

C. FLAME BRIGHTNESS CONTROL

Turn the flame brightness control knob to increase or decrease the brightness of the

flame and embers.

D. LED INDICATORS

Indicates the current function of the fireplace.

E. MANUAL SELECTION SWITCH

To choose between flame effect setting, flame effect with low heat setting, and flame

effect with high heat setting.

F. HEATER THERMOSTAT CONTROL

To adjust the temperature to your individual requirements, turn the thermostat control

clockwise all the way to turn on the heater. When the room reached the desired

temperature, turn the thermostat knob counter clockwise until you hear a click. Leave in

this position to maintain the room temperature at this setting. For additional heat, turn

clockwise until you hear the click again and the heater will turn on.

NOTE:

The heater may emit a slight, harmless odor when first used. This odor is a normal

condition caused by initial heating of internal heater parts and will not occur again.

RESETTING THE TEMPERATURE CUTOFF SWITCH

This unit is equipped with a thermostat which controls the temperature of the room. It

does this by turning the heater on and off. The heater is protected with a safety device

to prevent overheating. Should the heater overheat, an automatic cut out will turn the

heater off and it will not come back on without being reset. It can be reset by switching

the main ON/OFF SWITCH to OFF and waiting 5 minutes before switching the unit back

on.

CAUTION

If you need to continuously reset the heater, unplug the unit and call your local dealer.

REMOTE CONTROL USAGE

The fireplace is supplied with a radio frequency remote control. This remote control has

a range of approximately 50 feet. (15.25m), it does not have to be pointed at the

fireplace and can pass through most obstacles (including walls).

Remote Control Initialization

This procedure is required every time there is a loss of

power to the remote control in the fireplace. (i.e. power

failure, breaker tripped, main power switch is turned off)

1. Ensure that power is supplied through main

service panel.

2. Locate manual controls (refer to OPERATION

section).

3. Activate main power switch, red indicator lights will

flash momentarily.

4. Press ON button located on the remote control

transmitter (FIGURE 1). This will synchronize the

remote control transmitter and receiver.

Remote Control Usage

The remote control operates the fireplace levels

sequentially. The level is increased every time the ON

button on the transmitter is pressed. The fireplace can

be turned off at any point by pressing the OFF button

on the remote control transmitter.

Level 1: The flame effect is turned on and the first red

indicator light flashes momentarily.

Level 2: The flame effect remains on, the heater is

activated to the low heat setting, and the first and

second red indicator lights flash momentarily.

Level 3: The flame effect remains on, the heater is set

to the high heat setting, and all three red indicators

flash momentarily.

MANUAL SELECTION SWITCH

Operates fireplace in the same matter as the remote

control transmitter. Pressing the right side of this switch

has the same effect as the button on the

remote control and the right side has the same effect as

the button of the remote control. Pressing once to

the left activates Level 1, twice activates Level 2, three

times activates Level 3. Pressing to the left side turns

the fireplace off.

FIGURE 1

Level 1 Indicator

Level 2 Indicator

Level 3 Indicator

SF55992-AU

REPLACEMENT PARTS

FIREBOX, REG DLX SYMPHONY

CATALOGUE NO. SF55992-AU

PART NO. 6900420859

MOD.LEVEL NONE

REPLACEMENT PART REPLACEMENT PART NO.

1. LOG SET 0437960100RP

2. PROJECTION SCREEN 0437970100RP

3. FLICKER MOTOR 3000240200RP

4. HEATER ASSEMBLY 2200550100RP

5. THERMOSTAT 2300150100RP*

6. MAIN ON/OFF SWITCH 2800070100RP

7. FLAME SPEED CONTROL 3000410100RP

8. LIGHT DIMMER 3000420100RP

9. CORD SET 4100080159RP

10.LAMPHOLDER UPPER/LOWER 4200050100RP

11.MIRROR 5900060300RP

12.REFLECTOR ASSEMBLY 5900070100RP

13.FRONT GLASS 5900000100RP

14.DIMMER LIGHT CONTROL KNOB 8800000100RP

15.FLAME SPEED CONTROL KNOB 8800000200RP

16.THERMOSTAT CONTROL KNOB 8800000300RP

17.FOOT FIREPLACE 8800090100RP

18.REMOTE TRANSMITTER 3000530300RP

18.REMOTE RECIEVER BOARD 3000550100RP

18.SWITCH BOARD 3000530200RP

SF55992-AU

WIRING DIAGRAM

SF55992-AU

WIRING DIAGRAM

If unit was operating prior to servicing allow at least 10 minutes for light bulbs and

heating element to cool off to avoid accidental burning of skin.

Disconnect power before attempting any maintenance or cleaning to reduce the risk of

electric shock or damage to persons.

Light bulbs need to be replaced when you notice a dark section of the flame or when the

clarity and detail of the log exterior disappears. There are two bulbs at the top of the

opening that illuminates the log set exterior and four bulbs under the log set which

generate the flames and embers.

It is a good idea to replace all of the light bulbs at one time if they are close to the end of

their rated life. Group replacement will reduce the number of times you need to open

the unit to replace the light bulbs.

TO REPLACE UPPER LIGHT BULBS

1. Remove the firebox trim by placing your hand on the grill section, grasping the

trim and pulling outwards releasing the retainer clips.

2. Remove the mounting screw in the center of the glass and remove the retainer

bracket.

3. Remove the glass by lifting up from the bottom.

CAUTION

Even though the glass is safety glass it may break if bumped, struck of dropped.

Care must be taken when handling the glass.

4. Locate upper bulbs inside the center of the firebox at the top.

5. Replace bulb(s) that require replacement, holding onto the light socket when

while unscrewing.

6. Reassemble in the reverse order as above.

UPPER BULB-Quantity 2 chandelier or candelabra bulbs with an E-12 (small)

socket base, 15 watt rating.

CAUTION DO NOT EXCEED 15 WATTS PER BULB

If unit was operating prior to servicing allow at least 10 minutes for light bulbs and

heating element to cool off to avoid accidental burning of skin.

Disconnect power before attempting any maintenance or cleaning to reduce the risk of

electric shock or damage to persons.

Light bulbs need to be replaced when you notice a dark section of the flame or when the

clarity and detail of the log exterior disappears. There are two bulbs at the top of the

opening that illuminates the log set exterior and four bulbs under the log set which

generate the flames and embers.

It is a good idea to replace all of the light bulbs at one time if they are close to the end of

their rated life. Group replacement will reduce the number of times you need to open

the unit to replace the light bulbs.

TO REPLACE LOWER LIGHT BULBS

1. Remove the firebox trim by placing your hand on the grill section, grasping the

trim and pulling outwards releasing the retainer clips.

2. Remove the mounting screw in the center of the glass and remove the retainer

bracket.

3. Remove the glass by lifting up from the bottom.

CAUTION

Even though the glass is safety glass it may break if bumped, struck of dropped.

Care must be taken when handling the glass.

4. Only handle the log set by the ember bed and not by the logs. To remove the log

set lift up the front edge of log set until it clears the front tabs. Pull out until the

rear tab clears the back ledge, and then lift out.

5. Replace bulb(s) that require replacement, holding onto the light socket when

while unscrewing.

6. Replace the log by pushing it down and in until it rests against the mirror.

7. Reassemble in the reverse order as above.

LOWER BULB-Quantity 4 chandelier or candelabra bulbs with an E-12 (small)

socket base, 60 watt rating.

CAUTION DO NOT EXCEED 60 WATTS PER BULB

Table des matières

Autres manuels Dimplex Cheminée intérieure

Dimplex

Dimplex RITZ20W Manuel utilisateur

Dimplex

Dimplex BLF5051-INT Manuel utilisateur

Dimplex

Dimplex GDS28L8-904ST Manuel utilisateur

Dimplex

Dimplex DIMPLEX ELECTRIC FIREPLACE Manuel utilisateur

Dimplex

Dimplex PF2325 Manuel utilisateur

Dimplex

Dimplex DFI2310 Manuel utilisateur

Dimplex

Dimplex Optiflame Toluca Deluxe TLC20LX Mode d’emploi

Dimplex

Dimplex Optiflame Gorstan GST20 Mode d’emploi

Dimplex

Dimplex Ignite XLF50 Manuel utilisateur

Dimplex

Dimplex DFB8842 Manuel utilisateur

Dimplex

Dimplex Ignite 50" Manuel utilisateur

Dimplex

Dimplex 690932 Series Manuel utilisateur

Dimplex

Dimplex TANGO TNG20 Manuel utilisateur

Dimplex

Dimplex THWG XLF50 Manuel utilisateur

Dimplex

Dimplex GDS28G8-1802W Manuel utilisateur

Dimplex

Dimplex DF2608-EU Manuel utilisateur

Dimplex

Dimplex Optiflame MiniMozart FGA15E Mode d’emploi

Dimplex

Dimplex BLF74 Manuel utilisateur

Dimplex

Dimplex EWM-COPPER Guide de démarrage rapide

Dimplex

Dimplex 5011139048455 Manuel utilisateur

Dimplex

Dimplex X1B Black Manuel utilisateur

Dimplex

Dimplex RANA LED Manuel utilisateur

Dimplex

Dimplex THWG XLF50 Manuel utilisateur

Dimplex

Dimplex VIVALDI DE LUXE Manuel utilisateur

Manuels Cheminée intérieure populaires d'autres marques

Brigantia

Brigantia 35-DVRS31N-2 Manuel du propriétaire

Nordpeis

Nordpeis Bergen Manuel utilisateur

Superior

Superior BCT2536TMN Manuel utilisateur

Quadra-Fire

Quadra-Fire 5100I-GD-B Manuel utilisateur

Renaissance

Renaissance RUMFORD 1000 Manuel utilisateur

Lacunza

Lacunza IV-800 Manuel utilisateur

Baxi

Baxi 940 Instructions d'utilisation

Dru

Dru Maestro 60/2 Tall RCH Manuel utilisateur

Diamond Fireglass

Diamond Fireglass SS-O22 Manuel utilisateur

HearthStone

HearthStone Windsor Bay 8830 Manuel de programmation

Napoleon

Napoleon ASCENT B42 Manuel utilisateur

Enviro

Enviro E33GI Manuel utilisateur

Smeg

Smeg L30 FABE Instructions de montage

KEDDY

KEDDY K700 Manuel utilisateur

Godin

Godin 3451 Manuel utilisateur

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manuel utilisateur

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manuel utilisateur

Desa

Desa CCFPDFT Manuel d'utilisation