DFI PT880-ALF Manuel utilisateur

Addendum

The PT880-ALF system board supports two IEEE 1394 ports. It is equipped

with an IEEE 1394 port at the rear I/O panel and a 10-pin connector at

location J8 for connecting an additional IEEE 1394 port.All other information in

this manual pertains to the PT880-ALF too. Please refer to this manual for

reference.

1/1 936-PT8806-300

79101418

PT880-AL

PT800-AL

Rev.A+

System Board

User’s Manual

79100349

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior

written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose.The user will assume the entire risk of the use or

the results of the use of this document. Further, the manufacturer

reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or

entity of such revisions or changes.

Trademarks

Windows®98, Windows®98 SE, Windows®ME, Windows®2000,

Windows NT®4.0 and Windows®XP are registered trademarks of

Microsoft Corporation. Intel®, Pentium®4 and Celeron are regis-

tered trademarks of Intel Corporation. VIA is a registered trade-

mark of VIA Technologies, Inc. Award is a registered trademark of

Award Software, Inc. Other trademarks and registered trademarks

of products appearing in this manual are the properties of their

respective holders.

Caution

To avoid damage to the system:

• Use the correct AC input voltage range.....

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

the manufacturer.

• Dispose of used batteries according to the battery

manufacturer’s

instructions.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a

residential installation. This equipment generates, uses and can ra-

diate radio frequency energy and, if not installed and used in ac-

cordance with the instruction manual, may cause harmful interfer-

ence to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Notice

This user’s manual contains detailed information about the system

board. If, in some cases, some information doesn’t match those

shown in the multilingual manual, the multilingual manual should

always be regarded as the most updated version. The multilingual

manual is included in the system board package.

To view the user’s manual, insert the CD into a CD-ROM drive.The

autorun screen (Main Board Utility CD) will appear. Click “User’s

Manual”.

System Board

This user’s manual is for the PT880-AL and PT800-AL system

boards. The only difference between these boards is the PT880-

AL system board supports dual channel memory interface.

Table of Contents

Chapter 1 - Introduction

1.1 Features and Specifications.................................................................................

1.2 Hyper-Threading Technology Functionality Requirements...

1.3 Package Checklist...........................................................................................................

Chapter 2 - Hardware Installation

2.1 System Board Layout ...........................................................................................

2.2 System Memory...........................................................................................................

2.3 CPU........................................................................................................................................

2.4 Jumper Settings.............................................................................................................

2.5 Rear Panel I/O Ports..............................................................................................

2.6 I/O Connectors...........................................................................................................

Chapter 3 - BIOS Setup

3.1 Award BIOS Setup Utility....................................................................................

3.2 VIA RAID BIOS Setting Utility........................................................................

3.3 Updating the BIOS.....................................................................................................

Chapter 4 - Supported Softwares

4.1 Desktop Management Interface.....................................................................

4.2 Drivers, Utilities and Software Applications.........................................

4.3 3D Audio Configuration........................................................................................

4.4 Installation Notes..........................................................................................................

103

104

Introduction

112

Appendix A - Enabling the Hyper-Threading

Technology

A.1 Enabling the Hyper-ThreadingTechnology...........................................

Appendix B - Using the Suspend to RAM

Function

B.1 Using the Suspend to RAM Function...................................................

Appendix C - System Error Messages

C.1 POST Beep....................................................................................................................

C.2 Error Messages...........................................................................................................

Appendix D - Troubleshooting

D.1 Troubleshooting Checklist.................................................................................

108

114

105

Introduction

1.1 Features and Specifications

1.1.1 Features

Chipset

• PT880-AL

- North bridge:VIA®PT880

Advanced high performance 128-bit DDR DRAM control-

ler

- South bridge:VIA® VT8237

• PT800-AL

- North bridge:VIA®PT800

- South bridge:VIA® VT8237

Processor

The system board is equipped with Socket 478 for installing one

of the following supported processors.

• Intel®Pentium®4 (Prescott and Northwood) processor up to

3.06GHz

- Intel Hyper-ThreadingTechnology

- FSB: 533MHz and 800MHz

• Intel®Celeron®processor

- 400MHz system data bus

System Memory

• Supports dual channel (128-bit wide) memory interface

(PT880-AL only)

• Three 184-pin DDR DIMM sockets

• Supports up to 3GB using PC1600 (DDR200), PC2100

(DDR266), PC2700 (DDR333) and PC3200 (DDR400)

unbuffered DDR SDRAM DIMM, 2.6V type

Chapter 1 - Introduction

DIMMs

2MBx64

4MBx64

8MBx64

Memory Size

16MB

32MB

64MB

DIMMs

16MBx64

32MBx64

64MBx64

Memory Size

128MB

256MB

512MB

Introduction

Expansion Slots

• 1 AGP slot

• 5 PCI slots

AGP (Accelerated Graphics Port)

AGP is an interface designed to support high performance 3D

graphics cards. It utilizes a dedicated pipeline to access system

memory for texturing, z-buffering and alpha blending.The universal

AGP slot supports AGP 8x with up to 2133MB/sec. bandwidth and

AGP 4x with up to 1066MB/sec. bandwidth for 3D graphics

applications. AGP in this system board will deliver faster and better

graphics to your PC.

Onboard Audio Features

• AC’97 2.2 extension compliant codec

• Supports Microsoft®DirectSound/DirectSound 3D

• AC’97 supported with full duplex, independent sample rate

converter for audio recording and playback

• S/PDIF-in/out compressed digital output

• 6-channel audio output via software

S/PDIF

S/PDIF is a standard audio file transfer format that transfers digital

audio signals to a device without having to be converted first to

an analog format. This prevents the quality of the audio signal

from degrading whenever it is converted to analog. S/PDIF is usu-

ally found on digital audio equipment such as a DAT machine or

audio processing device. The S/PDIF connector on the system

board sends surround sound and 3D audio signal outputs to am-

plifiers and speakers and to digital recording devices like CD re-

corders.

6-channel Audio

The audio jacks at the rear panel will support 6-channel audio only

when the audio utility is configured to support this function.The mic-

in at the rear will be disabled. Use the front audio’s mic-in jack.

Introduction

Onboard LAN Features

• Phy fast ethernet controller

• Integrated IEEE 802.3, 10BASE-T and 100BASE-TX compatible

PHY

• 32-bit PCI master interface

• Integrated power management functions

• Full duplex support at both 10 and 100 Mbps

• Supports IEEE 802.3u auto-negotiation

• Supports wire for management

Serial ATA (SATA) IDE Interface with RAID

Serial ATA is a storage interface that is compliant with SATA 1.0

specification. With speed of up to 1.5Gbps, it improves hard drive

performance even in data intensive environments such as audio/

video, consumer electronics and entry-level servers.

• Two SATA (Serial ATA) interfaces which are compliant with

SATA 1.0 specification (1.5Gbps interface)

• Supports RAID 0, RAID 1 and JBOD

IEEE 1394 Interface (optional)

• VIAVT6307 PCI 1394 integrated host controller

• Supports two 100/200/400 Mb/sec ports

IEEE 1394 is fully compliant with the 1394 OHCI (Open Host

Controller Interface) 1.1 specification. It supports up to 63 devices

that can run simultaneously on a system. 1394 is a fast external bus

standard that supports data transfer rates of up to 400Mbps. In

addition to its high speed, it also supports isochronous data transfer

which is ideal for video devices that need to transfer high levels of

data in real-time. 1394 supports both Plug-and-Play and hot

plugging.

PCI Bus Master IDE Controller

• Supports ATA/33, ATA/66, ATA/100 and ATA/133 hard drives

• UDMA Modes 3, 4, 5 and 6 Enhanced IDE (data transfer rate

up to 133MB/sec.)

• Bus mastering reduces CPU utilization during disk transfer

• Supports ATAPI CD-ROM, LS-120 and ZIP

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels DFI Carte mère

DFI

DFI PL610-C622 Manuel utilisateur

DFI

DFI KD631-C236 Manuel utilisateur

DFI

DFI G486-EVB Manuel utilisateur

DFI

DFI CMS100 Manuel utilisateur

DFI

DFI LanParty NF3 Ultra-DF Manuel utilisateur

DFI

DFI KD631-C236/Q170 Manuel utilisateur

DFI

DFI CS350-C246 Manuel utilisateur

DFI

DFI PB50-V3 Manuel utilisateur

DFI

DFI G486VPA Manuel utilisateur

DFI

DFI PT880-ALE Manuel utilisateur

DFI

DFI WL051-BCC-B Manuel utilisateur

DFI

DFI nF4 Ultra-DAGF Manuel utilisateur

DFI

DFI CS101-C246 Manuel utilisateur

DFI

DFI SB331-D Manuel utilisateur

DFI

DFI ST2K Series Manuel utilisateur

DFI

DFI SB600-C Manuel utilisateur

DFI

DFI ICX610-C621A Manuel utilisateur

DFI

DFI G586VPM Manuel utilisateur

DFI

DFI 845PE-ML Manuel utilisateur

DFI

DFI MB630-CRM Manuel utilisateur

DFI

DFI Q7-100 Manuel utilisateur

DFI

DFI G686IPA Manuel utilisateur

DFI

DFI SD630-H110-000G Manuel utilisateur

DFI

DFI SB102-D Manuel utilisateur

Manuels Carte mère populaires d'autres marques

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuel utilisateur