DFI P2XBL/E Manuel utilisateur

P2XBL/e

Rev. A+

System Board

Users Manual

36500829

This publication contains information that is protected by copyright. No

part of it may be reproduced in any form or by any means or used to

make any transformation/adaptation without the prior written permission

from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any express

or implied warranties of merchantability or fitness for any particular purpose.

The user will assume the entire risk of the use or the results of the use of

this document.Further,the manufacturer reserves the right to revise this

publication and make changes to its contents at any time, without obligation

to notify any person or entity of such revisions or changes.

Trademarks

Microsoft®MS-DOS®, WindowsTM and Windows®95 are registered

trademarks of Microsoft Corporation. Intel and Pentium are registered

trademarks of Intel Corporation. Cyrix, 6x86, 6x86L and 6x86MX are

registered trademarks of Cyrix Corporation. AMD, K5 and K6 are

registered trademarks ofAdvanced Micro Devices,Inc. IBM is a registered

trademark of International Business Machine Corporation. Award is a

registered trademark of Award Software, Inc. Other trademarks and

registered trademarks of products appearing in this manual are the

properties of their respective holders.

Caution:

Danger of explosion if battery incorrectly replaced.

Replace only with the same or equivalent type recommended by the

manufacturer.

Dispose of used batteries according to the battery manufacturers

instructions.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and the receiver.

 Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

 Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Table of Contents

Chapter 1 - Introduction

1.1 Features and Specifications ......................................................................

1.2 Package Checklist .........................................................................................

Chapter 2 - Hardware Installation

2.1 System Board Layout .................................................................................

2.2 System Memory .............................................................................................

2.3 DIP Switch Settings of the Processors ............................................

2.4 Jumper Settings for Wake-On-Keyboard/Mouse........................

2.5 Jumper Settings for Clearing CMOS Data. ...................................

2.6 Jumper Settings for CPU Front Side Bus .......................................

2.7 Connecting the Ribbon Cables and Wires of the Ports

and Connectors .............................................................................................

Chapter 3 - Award BIOS Setup Utility

3.1 The Basic Input/Output System ...........................................................

3.1.1 Standard CMOS Setup.............................................................

3.1.2 BIOS Features Setup ..................................................................

3.1.3 Chipset Features Setup.............................................................

3.1.4 Power Management Setup ......................................................

3.1.5 PNP/PCI Configuration .............................................................

3.1.6 Load Fail-Safe Settings ...............................................................

3.1.7 Load Optimal Settings ..............................................................

3.1.8 Integrated Peripherals .................................................................

3.1.9 Supervisor Password ..................................................................

3.1.10 User Password...............................................................................

3.1.11 IDE HDD Auto Detection .....................................................

3.1.12 Save & Exit Setup ........................................................................

3.1.13 Exit Without Saving .....................................................................

Chapter 4 - Supported Softwares

4.1 Desktop Management Interface ..........................................................

Appendix A - System Error Messages

A.1 POST Beep ......................................................................................................

A.2 Error Messages ...............................................................................................

Appendix B - Troubleshooting

B.1 Troubleshooting Checklist. ........................................................................

1.1 Features and Specifications

1.1.1 Features

Chipset

 Intel440BX AGPset

Processor

The system board is equipped with a 242-pin IntelSlot 1

processor slot for installing an Intel PentiumII processor that is

packaged in an SEC (Single Edge Contact) cartridge or an Intel

CeleronTM processor.

 233/66MHz, 266/66MHz, 300/66MHz, 300/100MHz,

333/66MHz, 350/100MHz, 400/100MHz or 450/100MHz

PentiumII processor with 512KB L2 cache

 266/66MHz, 300/66MHz, 300A/66MHz or 333/66MHz

Intel CeleronTM processor

System Memory

The system board supports 8MB to 384MB memory. It is equipped

with three 168-pin DIMM sockets using x64/x72 unbuffered PC

SDRAM, 3.3V. The PC SDRAMs supported are PC-66 SDRAM for

66MHz FSB and PC-100 SDRAM for 100MHz FSB. The system

board also supports EC and ECC (uses x72 PC SDRAM).

Expansion Slots

The system board is equipped with 1 dedicated AGP slot, 3

dedicated PCI slots, 2 dedicated 16-bit ISA slots and 1 shared PCI/

ISA slot. All PCI and ISA slots are bus masters.

Desktop Management Interface (DMI)

The system board comes with a DMI 2.0 built into the BIOS. The

DMI utility in the BIOS automatically records various information

about your system configuration and stores these information in the

Chapter 1 - Introduction

Introduction

DMI pool, which is a part of the system board's Plug and Play

BIOS. DMI, along with the appropriately networked software, is

designed to make inventory, maintenance and troubleshooting of

computer systems easier. Refer to Chapter 4 for instructions on

using the DMI utility.

Onboard I/O

 Two NS16C550A-compatible DB-9 serial ports

 One SPP/ECP/EPP DB-25 parallel port

 One floppy drive interface supports up to two 2.88MB floppy

drives

 One mini-DIN-6 PS/2 mouse port

 One mini-DIN-6 PS/2 keyboard port

 One WOL (Wake-On-LAN) connector

PCI Bus Master IDE Controller

 Two PCI IDE interfaces support up to four IDE devices

 Ultra DMA/33 supported (Synchronous Ultra DMA mode -

data transfer rate up to a maximum of 33MB/sec.)

 PIO Mode 3 and Mode 4 Enhanced IDE (data transfer rate up

to 16.6MB/sec.)

 Bus mastering reduces CPU utilization during disk transfer

 ATAPI CD-ROM supported

 LS-120 and ZIP supported

IrDA Interface

The system board is equipped with an IrDA connector for wireless

connectivity between your computer and peripheral devices. It

supports peripheral devices that meet the IrDA or ASKIR standard.

USB Ports

The system board is equipped with two USB ports. USB allows

data exchange between your computer and a wide range of

simultaneously accessible external Plug and Play peripherals.

BIOS

 Award BIOS, Windows95 Plug and Play compatible

 Flash EPROM for easy BIOS upgrades

Introduction

Power Supply Connector

The system board is equipped with an ATX power supply connector.

Using an ATX power supply, you can either shut down your com-

puter by pressing the Power button located on the front bezel of

your computer or by executing the Shut Down command under the

Windows95 operating system.Your system will then enter the Soft

Off state.

To power-on your system automatically, enable Resume On Alarm

in the Power Management Setup of the Award BIOS.This will allow

you to set the date and time you would like your system to power-

on.

1.1.2 Technology

AGP (Accelerated Graphics Port)

The system board is equipped with 1 AGP slot. AGP is an interface

designed to support high performance 3D graphics cards. It utilizes a

dedicated pipeline to access system memory for texturing, z-buffering

and alpha blending; delivering up to 533MB/sec. bandwidth for 3D

graphics applications. AGP in this PentiumII processor based system

board will deliver faster and better graphics with your PC.

PC SDRAM (Synchronous Dynamic Random Access Memory)

PC SDRAM uses a fast memory interface technology to meet the

memory bandwidth requirements of Intel processors and chipset.

This technology includes using the clock on the chip to synchronize

with the CPU clock so that the timing of the memory chips and the

timing of the CPU are synchronized. Please refer to Intels web site

for more information on PC SDRAM.

Creative SB-LINK

The system board is equipped with a Creative SB-LINK connector.

SB-LINK serves as a bridge between the system board and a

Creative PCI sound card to deliver Sound BlasterAWE64D

performance. Refer to SB-LINK Connector in Chapter 2 for more

information.

Introduction

Ultra DMA/33 Bus Master IDE

Synchronous Ultra DMA mode provides data transfer rate up to a

maximum of 33MB/sec, which is twice the data transfer rate of

Enhanced IDE or ATA-2. This enables the CPU to operate more

efficiently when handling simultaneous events.

ECC (Error Checking and Correction)

ECC is a function that allows the system to recover from memory

failure. It detects single-bit and multiple-bit errors and corrects single-

bit error thus providing uninterrupted processing of data. To use this

function, you must install DIMM that supports parity.

ACPI (Advanced Configuration and Power Interface)

The system board is designed to meet the ACPI specification. ACPI

has energy saving features that enables PCs to implement Power

Management and Plug-and-Play with operating systems that support

OS Direct Power Management.

PC 97 Compliant

The system board is PC 97 compliant. This will optimize your PC

system to run Windows95 and Windows NTand future versions

of these operating systems.

1.1.3 Intelligence

Dual Function Power Button

Depending on the setting in the BIOS setup, this switch will allow

your system to enter the Soft-Off or Suspend mode. Soft-Off By

PWR-BTTN in the Power Management Setup (Chapter 3) allows

you to select the method of powering off your system.

External Modem Wake-up/Ring-on

The Modem Wake-Up feature allows the sleeping (Suspend mode)

PC to wake-up to respond to incoming calls. The Modem Ring-on

feature allows the Soft Power Down (Soft-Off) PC to power-on to

respond to incoming calls. Enable this function in the Resume On

Ring field of the Power Management Setup (Chapter 3).

Introduction

Note:

This feature supports external modem only.

RTC Timer to Power-On the System

The RTC installed on the system board allows your system to

automatically power-on on the set date and time. Set the date and

time you would like your system to power-on in the Resume On

Alarm field of the Power Management Setup (Chapter 3).

Wake-On-LAN Ready

The Wake-On-LAN function allows the network to wake up a Soft

Power Down (Soft-Off) PC. To use the Wake-On-LAN function,

make sure your LAN card also support this function. Refer to the

Wake-On-LAN Connector section (Chapter 2) and Resume On

LAN field in the Power Management Setup (Chapter 3).

Important:

The 5VSB power source of your power supply must support

≥

720mA (minimum).

Wake-On-Keyboard/Wake-On-Mouse

This function allows you to use the keyboard or mouse to power-on

the system. Refer to Jumper Settings for Wake-On-Keyboard/Wake-

On-Mouse in Chapter 2 and Keyboard/Mouse Power On in the

Integrated Peripherals setup of the Award BIOS in Chapter 3 for

more information.

Important:

The power button will not function once a keyboard password

has been set in the KB Power On Password field of the

Integrated Peripherals setup. You must type the correct

password to power-on the system.

Virus Protection

Most viruses today destroy data stored in hard drives. The system

board is designed to protect the boot sector and partition table of

your hard disk drive. If an attempt is made to write to the boot

sector or partition table of the hard disk drive, the BIOS will halt the

system and an error message will appear. Refer to the Virus

Warning field in the BIOS Features Setup (Chapter 3).

Autres manuels pour P2XBL/E

Autres manuels DFI Carte mère

Manuels Carte mère populaires d'autres marques

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuel utilisateur