DFI NP900-B16C Manuel utilisateur

NP900-B16C

COM Express Board

User’s Manual

935-NP9001-000G

A07800843

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior writ-

ten permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any ex-

press or implied warranties of merchantability or fitness for any par-

ticular purpose.The user will assume the entire risk of the use or the

results of the use of this document. Further, the manufacturer re-

serves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or en-

tity of such revisions or changes.

Trademarks

Windows®2000, Windows®CE, Windows®XP and Windows®XP

Embedded are registered trademarks of Microsoft Corporation.

Product names or trademarks appearing in this manual are for iden-

tification purpose only and are the properties of the respective own-

ers.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation.This equipment generates, uses and can radiate radio fre-

quency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communi-

cations. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following meas-

ures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Table of Contents

About this Manual................................................................................

Warranty.................................................................................................

Static Electricity Precaution................................................................

Safety Measures.....................................................................................

About the Package...............................................................................

Chapter 1 - Introduction....................................................................

Specifications...................................................................................................................................

Features..............................................................................................................................................

Chapter 2 - Hardware Installation....................................................

System Board Layout ..........................................................................................................

Mechanical Diagram................................................................................................................

System Memory..........................................................................................................................

Jumper Settings............................................................................................................................

Connectors......................................................................................................................................

LEDs......................................................................................................................................................

SPI Flash ROM Socket.........................................................................................................

Cooling Options.........................................................................................................................

Installing NP900-B16C onto a Carrier Board..............................................

Chapter 3 - BIOS Setup......................................................................

Award BIOS Setup Utility.................................................................................................

Updating the BIOS..................................................................................................................

Chapter 4 - Supported Softwares.....................................................

Drivers for Windows Vista System..........................................................................

Drivers for Windows XP System..............................................................................

Appendix A - Watchdog Timer.............................................................

118

About this Manual

An electronic file of this manual is included in the CD. To view the

user’s manual in the CD, insert the CD into a CD-ROM drive. The

autorun screen (Main Board Utility CD) will appear. Click “User’s

Manual” on the main menu.

Warranty

1. Warranty does not cover damages or failures that arised from

misuse of the product, inability to use the product, unauthorized

replacement or alteration of components and product specifica-

tions.

2. The warranty is void if the product has been subjected to physi-

cal abuse, improper installation, modification, accidents or unau-

thorized repair of the product.

3. Unless otherwise instructed in this user’s manual, the user may

not, under any circumstances, attempt to perform service, adjust-

ments or repairs on the product, whether in or out of warranty.

It must be returned to the purchase point, factory or authorized

service agency for all such work.

4. We will not be liable for any indirect, special, incidental or

consequencial damages to the product that has been modified

or altered.

Introduction

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board,

components or devices even before installing them in your system

unit. Static electrical discharge can damage computer components

without causing any signs of physical damage. You must take extra

care in handling them to ensure against electrostatic build-up.

1. To prevent electrostatic build-up, leave the board in its anti-static

bag until you are ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of

the components, contacts or connections.

5. Avoid touching the pins or contacts on all modules and connec-

tors. Hold modules or connectors by their ends.

Important:

Electrostatic discharge (ESD) can damage your processor,

disk drive and other components. Perform the upgrade in-

struction procedures described at an ESD workstation

only. If such a station is not available, you can provide

some ESD protection by wearing an antistatic wrist strap

and attaching it to a metal part of the system chassis. If a

wrist strap is unavailable, establish and maintain contact

with the system chassis throughout any procedures requir-

ing ESD protection.

Safety Measures

To avoid damage to the system:

• Use the correct AC input voltage range.....

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Introduction

About the Package

The package contains the following items. If any of these items are

missing or damaged, please contact your dealer or sales representa-

tive for assistance.

;The system board

;A user’s manual

;One heat sink

;One “Main Board Utility” CD

;One QR (Quick Reference)

The board and accessories in the package may not come similar to

the information listed above. This may differ in accordance to the

sales region or models in which it was sold. For more information

about the standard package in your region, please contact your

dealer or sales representative.

Introduction

Processor

Chipset

System Memory

BIOS

Graphics

DMI

LAN

Audio

Expansion

Interfaces

• Intel®AtomTM N270 (Diamondville SC) processor

• 1.6GHz core frequency, 1.10V voltage

• 2.5W thermal design power

• 512KB on-die second level cache

• 533-MT/s FSB

• 22x22 mm, 1.0 mm ball pitch and 437 balls FCBGA

• Intel®chipset

- Intel®945GSE Graphics Memory Controller Hub (GMCH)

- Intel®82801GBM I/O Controller Hub (ICH7M)

• One 200-pin SODIMM socket (1.8V)

• Maximum memory supports up to 2GB

• Supports 400MHz and 533MHz DDR2 SDRAM

• SPI interface BIOS (8Mbit)

• 133/166MHz internal graphics core render frequency at 1.05V

core voltage

• One SDVO port (Port B)

- SDVO slot reversal not supported

• Supports 18-bit dual-channel LVDS

• Supports CRT resolutions up to SXGA+

• DMI lane width - x2 only

• DMI lane reversal not supported

• One Realtek RTL8111C PCI Express Gigabit controller

• Supports 10Mbps, 100Mbps and 1Gbps data transmission

• IEEE 802.3 (10/100Mbps) and IEEE 802.3ab (1Gbps) compliant

• Supports Azalia AC97 interface

• PCI 2.3 interface (supports 4 PCI bus masters)

• Supports 8 USB ports (USB 1.1/2.0 host controllers)

• Supports 3 PCIE x1 interface

Chapter 1 - Introduction

Specifications

Introduction

Serial ATA

IDE

Temperature

Humidity

Power

Regulatory

PCB

• SATA interface supports data transfer rate up to 1.5Gb/s

(150MB/s) per port

• Two SATA ports with independent DMA operation supported

on ports 0 and 2

• Two-mode operation supports legacy mode using I/O space or

an AHCI mode using memory space

• SATA and PATA can be used in a combined function mode

(When SATA is used with PATA, AHCI mode is not supported.)

• Bus Master IDE (PATA) controller

• Supports up to two IDE devices

• Ultra ATA 100/66/33

• Operating: 0oC to 60oC

• Operating: 10% to 90%

• Input: 12V, 5VSB, VCC_RTC

• EMC: CE, FCC Part 15 Class B

• Dimensions

- COM Express basic form factor

- 9.5cm (3.74") x 12.5cm (4.9")

• Compliance

- PICMG COM Express R1.0 basic form factor, Type 2

Introduction

The Watchdog Timer function allows your

application to regularly “clear” the system at

the set time interval. If the system hangs or fails to function, it will

reset at the set time interval so that your system will continue to

operate.

DDR2 is a higher performance DDR technology

whose data transfer rate delivers bandwidth of 4.3

GB per second and beyond. That is twice the speed of the conven-

tional DDR without increasing its power consumption. DDR2

SDRAM modules work at 1.8V supply compared to 2.6V memory

voltage for DDR modules. DDR2 also incorporates new innovations

such as the On-Die Termination (ODT) as well as larger 4-bit pre-

fetch against DDR which fetches 2 bits per clock cycle.

The integrated graphics delivers exceptional 3D

graphics performance.

The Realtek RTL8111C PCI Express Gigabit

controller supports up to 1Gbps data

transmission.

watchdog timer

graphics

Features

DDR2

gigabit lan

Table des matières

Autres manuels DFI Carte mère

Manuels Carte mère populaires d'autres marques

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuel utilisateur