DFI 865PE-ALE Manuel utilisateur

83400438

865PE-ALE Rev. B

System Board

User’s Manual

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior

written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose.The user will assume the entire risk of the use or

the results of the use of this document. Further, the manufacturer

reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or

entity of such revisions or changes.

Trademarks

Windows®98 SE, Windows®ME, Windows®2000, Windows NT®

4.0 and Windows®XP are registered trademarks of Microsoft

Corporation. Intel®, Pentium®4 and Celeron are registered

trademarks of Intel Corporation. Award is a registered trademark of

Award Software, Inc. Other trademarks and registered trademarks

of products appearing in this manual are the properties of their

respective holders.

Caution

To avoid damage to the system:

• Use the correct AC input voltage range.....

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

the manufacturer.

• Dispose of used batteries according to the battery

manufacturer’s

instructions.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

About this Manual

This user’s manual contains detailed information about the system

board. If, in some cases, some information doesn’t match those

shown in the multilingual manual, the multilingual manual should al-

ways be regarded as the most updated version. The multilingual

manual is included in the system board package.

To view the user’s manual, insert the CD into a CD-ROM drive.The

autorun screen (Mainboard Utility CD) will appear. Click the

“TOOLS” icon then click “Manual” on the main menu.

About the Package

The system board and accessories in the package may not come

similar to the information stated in this manual. This may differ in

accordance to the sales region or models in which it was sold. For

more information about the standard package in your region, please

contact your dealer or sales representative.

Warranty

1. Warranty does not cover damages or failures that arised from

misuse of the product, inability to use the product, unauthorized

replacement or alteration of components and product

specifications.

2. The warranty is void if the product has been subjected to

physical abuse, improper installation, modification, accidents or

unauthorized repair of the product.

3. Unless otherwise instructed in this user’s manual, the user may

not, under any circumstances, attempt to perform service,

adjustments or repairs on the product, whether in or out of

warranty. It must be returned to the purchase point, factory or

authorized service agency for all such work.

4. We will not be liable for any indirect, special, incidental or

consequencial damages to the product that has been modified

or altered.

Table of Contents

Chapter 1 - Introduction

1.1 Specifications......................................................................................................................

1.2 Special Features of the System Board.....................................................

1.3 Package Checklist.........................................................................................................

Chapter 2 - Hardware Installation

2.1 System Board Layout ...........................................................................................

2.2 System Memory...........................................................................................................

2.3 CPU........................................................................................................................................

2.4 Jumper Settings.............................................................................................................

2.5 Rear Panel I/O Ports..............................................................................................

2.6 I/O Connectors...........................................................................................................

Chapter 3 - Award BIOS Setup Utility

3.1 The Basic Input/Output System.....................................................................

3.2 Updating the BIOS.....................................................................................................

Chapter 4 - Supported Softwares

4.1 Drivers, Utilities and Software Applications.....................................

4.2 Installation Notes......................................................................................................

102

Introduction

Appendix A - Enabling the Hyper-Threading

Technology

A.1 Enabling the Hyper-Threading Technology...........................................

Appendix B - System Error Messages

B.1 POST Beep....................................................................................................................

B.2 Error Messages...........................................................................................................

Appendix C - Troubleshooting

C.1 Troubleshooting Checklist.................................................................................

103

106

108

Introduction

Chapter 1 - Introduction

1.1 Specifications

Processor

• Intel®Pentium®4 (Prescott and Northwood) processor up to

3.4GHz+

- Intel Hyper-Threading Technology

- FSB: 533MHz and 800MHz

• Intel®Celeron®D processor

- 533MHz system data bus

• Intel®Celeron®processor

- 400MHz system data bus

• Processor socket: Socket 478

Chipset

• Intel®865PE chipset

- Intel®82865PE Memory Controller Hub (MCH)

- Intel®82801ER I/O Controller Hub (ICH5)

System Memory

• Two 184-pin DDR DIMM sockets

• Supports dual channel (128-bit wide) memory interface

• Supports up to 2GB system memory

• Synchronous operation with processor system bus

- PC2100/PC2700/PC3200 (DDR266/DDR333/DDR400)

with 800MHz FSB CPU. DDR333 will run at 320MHz

memory frequency when used with 800MHz FSB CPU.

- Use PC2100/PC2700 (DDR266/DDR333) with 533MHz

FSB CPU

- Use PC2100 (DDR266) with 400MHz FSB CPU

• Supports non-ECC DIMMs

• Supports up to 512Mb DRAM densities

• Supports unbuffered DIMMs

BIOS

• Award BIOS, Plug and Play compatible

• 2Mbit flash memory

Introduction

Energy Efficient Design

• Supports ACPI specification and OS Directed Power

Management

• Supports ACPI STR (Suspend to RAM) function

• Wake-On-Events include:

- Wake-On-PS/2 Keyboard/Mouse

- Wake-On-USB Keyboard/Mouse

- Wake-On-Ring (external modem)

- Wake-On-LAN

- RTC timer to power-on the system

• AC power failure recovery

Hardware Monitor

• Monitors CPU temperature and overheat alarm

• Monitors CPU/1.5V/3.3V/5V/±12V/VBAT/5VSB voltages

• Monitors the speed of the CPU fan

• CPU Overheat Protection function monitors CPU temperature

and fan during system boot-up - automatic shutdown upon

system overheat

Onboard Audio Features

• 6-channel audio CODEC

• 20-bit stereo full-duplex codec with independent variable sam-

pling rate

• True stereo line level outputs

• S/PDIF-in/out interface

Onboard LAN Features

• Realtek RTL8100C PCI controller

• Integrated power management functions

• Full duplex support at both 10 Mbps and 100 Mbps

• Supports IEEE 802.3u auto-negotiation

• Supports wire for management

Serial ATA Interface

• Supports two SATA (Serial ATA) interfaces which are compliant

with SATA 1.0 specification (1.5Gbps interface)

IDE Interface

• Supports up to UltraDMA100Mbps hard drives

Introduction

Rear Panel I/O Ports

• 1 mini-DIN-6 PS/2 mouse port

• 1 mini-DIN-6 PS/2 keyboard port

• 1 DB-25 parallel port

• 1 DB-9 serial port

• 1 RJ45 LAN port

• 4 USB 2.0 ports

• Mic-in, line-out and line-in jacks

I/O Connectors

• 2 connectors for 4 additional external USB 2.0 ports

• 1 connector for one external serial port

• 1 front audio connector for external line-out and mic-in jacks

• 1 CD-in internal audio connector

• 1 S/PDIF connector for optical cable connection

• 1 IrDA connector

• 2 Serial ATA connectors

• 2 IDE connectors

• 1 floppy connector

• 1 20-pin ATX power connector

• 1 4-pin ATX 12V power connector

• 1 front panel connector

• 2 fan connectors

Expansion Slots

• 1 AGP 8x slot

• 5 PCI slots

PCB

• ATX form factor

• 30.5cm (12.01") x 20cm (7.87")

Introduction

1.2 Special Features of the System Board

Hyper-Threading Technology Functionality Requirements

The system board supports Intel processors with Hyper-Threading

Technology. Enabling the functionality of Hyper-Threading Technology

for your computer system requires ALL of the following platforms.

Components:

• CPU - an Intel®Pentium®4 Processor with HT Technology

• Chipset - an Intel®chipset that supports HT Technology

• BIOS - a BIOS that supports HT Technology and has it enabled

• OS - an operating system that includes optimizations for HT

Technology

Refer to Appendix A for information about enabling the functionality

of the Hyper-Threading Technology. For more information on Hyper-

Threading Technology, go to: www.intel.com/info/hyperthreading.

CPU Overheat Protection

CPU Overheat Protection has the capability of monitoring the CPU’s

temperature during system boot up. Once the CPU’s temperature

exceeded the temperature limit pre-defined by the CPU, the system

will automatically shutdown.This preventive measure has been added

to protect the CPU from damage and insure a safe computing

environment.

DDR

DDR (Double Data Rate) is a type of SDRAM that doubles the

data rate through reading and writing at both the rising and falling

edge of each clock. This effectively doubles the speed of operation

therefore providing two times faster data transfer.

6-channel Audio

The audio jacks at the rear panel will support 6-channel audio only

when the audio utility is configured to support this function.The mic-

in at the rear will be disabled. Use the front audio’s mic-in jack.

Table des matières

Autres manuels DFI Carte mère

DFI

DFI Blood-Iron LanParty Bi 785G-M35 Manuel utilisateur

DFI

DFI ADS630 Manuel utilisateur

DFI

DFI CS101-H310 Manuel utilisateur

DFI

DFI G586VPS Pro Manuel utilisateur

DFI

DFI SD100-H110/Q170 Manuel utilisateur

DFI

DFI AR100-DR Manuel utilisateur

DFI

DFI CD951-C Series Manuel utilisateur

DFI

DFI LanParty UT nF3 Ultra-D Manuel utilisateur

DFI

DFI QB701-B Series Manuel utilisateur

DFI

DFI CM64-AL Manuel utilisateur

DFI

DFI PT880-AL Manuel utilisateur

DFI

DFI PE11-TC Manuel utilisateur

DFI

DFI NB71-BC Manuel utilisateur

DFI

DFI AL701 Manuel utilisateur

DFI

DFI 748-AL Manuel utilisateur

DFI

DFI LANParty UT ICFX3200-T2R/G Manuel utilisateur

DFI

DFI PE11-EC Manuel utilisateur

DFI

DFI KD600-H110/Q170 Manuel utilisateur

DFI

DFI CA64-BC Manuel utilisateur

DFI

DFI HD330 Manuel utilisateur

DFI

DFI SB331-D Manuel utilisateur

DFI

DFI 852GME-MGF Pro Manuel utilisateur

DFI

DFI P5BV3+ Manuel utilisateur

DFI

DFI SD330-Q170 Manuel utilisateur

Manuels Carte mère populaires d'autres marques

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuel utilisateur