Dexter Laundry T-1450 Manuel d'installation

OPL PROGRAMMING V-SERIES

TWO WAYS TO MODIFY PROGRAMMING OF THE V-SERIES OPL SIX (6)

PREPROGRAMMED FORMULAS

#1 Programming can be accomplished manually using the machine controls or by connecting to

the machine control using a PDA (personal digital assistant). For instructions on using a PDA

with this washer control, please contact your local Dexter distributor.

The keypad layout for the washer control is shown above.

#2 Manual Wash Cycle Programming Instructions

1. Turn on the power to the washer.

2. Turn the Run/Program key to the Program position. Display will show “C O” and the

“ADD BLEACH” will blink and will continue to blink during the programming mode.

3. Press the “DOWN” or “UP” buttons to select which cycle to alter. When the desired

cycle number is displayed, press “START”.

4. The display should now show a “b”. The “b” and the cycle indicator lights indicate

which bath is being selected to alter. Press the “UP” and “DOWN” buttons to select a

bath to change and then press “START”. The indicator lights are shown below.

FINAL

RINSE

PRE

WASH

FLUSH WASH RINSE SPIN

When “RINSE” is selected, “b r1” through “b r4” may be selected. There may be

multiple rinses that are indicated by r1, r2, r3 and r4.

5.Each bath can be programmed with the following options. Use the “DOWN” and “UP” keys to

select the desired setting and the “START” key to move to the next option.

DISPLAY FUNCTION OPTIONS

Ct ** Tumble Time Two-digit amount of time in minutes.

t ** Water Temperature HH for hot, CH for warm, CC for cold

and EE for no water.

L ** Water Level Lo for low, Hl for high.

dF * Type of Fill d for delayed fill, t for timed fill.1

S ** Spin Time Two-digit amount of time in minutes.

IS * Injection Source Single digit code indicating injector signal(s).2

1 A delayed fill will pause the time count until the selected level is reached. A timed fill

will only fill for a predetermined amount of time.

2Codes for injections sources are defined at the end of the programming section. When

the No Water bath is selected, the electronic controller prohibits injection signals. The

programmed injection source value is ignored.

To exit the programming of a bath, press the “STOP” button once and use the “UP” and

“DOWN” keys select another bath. Press the “STOP” button again to select a different cycle to

change. To end programming, turn the key to “RUN” position

Note: The Wash Cycle programming mode will automatically exit and return to

the Idle mode if no buttons are pushed for one minute.

WASHER CYCLE PARAMETER RANGES

The range of each cycle parameter is shown below:

Cycle Time 0 to 15 minutes for Prewash, Wash, Rinse1, 2, 3 and 4

1 to 15 minutes for Final Rinse

For the bathes that can, if the time is set to zero, then the

bath will be eliminated from the cycle.

Water Temperature HH – hot, CH – warm, CC – cold, EE – no water

Water Level HI – high, LO – low

Delay Fill The selections are “d” for delay the bath time until water

level is reached or “t” for decrement bath time during the

fill.

Spin Time 0 to 10 minutes for Prewash, Wash, Rinse, 2, 3 and 4

1 to 10 minutes for Final Spin

Injection Source 0 to 6

Cycle 1 Sheets & Pillowcases (Health Care)

Bath

Bath Cycle

Time

(min.)

Water

Temp.

Water

Level

Delay

Fill

Spin

Time

(min.)

Injection Source

Flush 3 CH HI d

Prewash 2 CH HI d

Wash 7 HH LO d 1 (Detergent)

Rinse 1 7 HH LO d 2 (Bleach)

Rinse 2 2 CH HI d 1

Rinse 3 2 CH HI d

Rinse 4

Final

Rinse

4 CH LO d 4 4 (Sour/Soft)

Cycle 2 Towels / Pads / Diapers (Health Care)

Bath

Bath Cycle

Time

(min.)

Water

Temp.

Water

Level

Delay

Fill

Spin

Time

(min.)

Injection Source

Flush 3 CH HI d

Prewash 2 CH HI d

Wash 7 HH LO d 1 (Detergent)

Rinse 1 1 HH HI d

Rinse 2 7 HH LO d 2 (Bleach)

Rinse 3 2 CH HI d 1

Rinse 4 2 CH HI d

Final

Rinse

4 CH LO d 5 4 (Sour/Soft)

Cycle 3 White Towels (Hotel / Motel)

Bath

Bath Cycle

Time

(min.)

Water

Temp.

Water

Level

Delay

Fill

Spin

Time

(min.)

Injection Source

Flush

Prewash

Wash 7 HH LO d 1 (Detergent)

Rinse 1 1 HH HI d

Rinse 2 7 HH LO d 2 (Bleach)

Rinse 3 2 CH HI d 1

Rinse 4 2 CH HI d

Final

Rinse

4 CH LO d 5 4 (Sour/Soft)

Cycle 4 Guest Laundry (Hotel / Motel or Health Care)

Bath

Bath Cycle

Time

(min.)

Water

Temp.

Water

Level

Delay

Fill

Spin

Time

(min.)

Injection Source

Flush 3 CH HI d

Prewash

Wash 7 HH LO d 5

(Detergent/Bleach)

Rinse 1 2 HH HI d

Rinse 2 2 CH HI d

Rinse 3 2 CH HI d

Rinse 4

Final

Rinse

4 CH LO d 4 4 (Sour/Soft)

Cycle 5 Rags & Mops (Hotel / Motel)

Bath

Bath Cycle

Time

(min.)

Water

Temp.

Water

Level

Delay

Fill

Spin

Time

(min.)

Injection Source

Flush 3 CH HI d

Prewash 2 CH HI d

Wash 2 CH HI d

Rinse 1 7 HH LO d 1 (Detergent)

Rinse 2 2 HH HI d

Rinse 3 7 HH LO d 2 (Bleach)

Rinse 4 2 CH HI d 1

Final

Rinse

2 CH LO d 5

Cycle 6 Colored Cotton Linen (Food & Beverage)

Bath

Bath Cycle

Time

(min.)

Water

Temp.

Water

Level

Delay

Fill

Spin

Time

(min.)

Injection Source

Flush 2 CH HI d

Prewash

Wash 10 HH LO d 1 (Detergent)

Rinse 1 7 HH LO d 2 (Bleach)

Rinse 2 2 CH HI d 1

Rinse 3 2 CH HI d

Rinse 4

Final

Rinse

4 CH LO d 4 6 (Sour/Starch)

RAPID ADVANCE MODE

To enter the Rapid Advance mode, turn the key CCW. The Rapid Advance setting is not marked

next to the key, but turning the CCW until it stops selects this mode. The Rapid Advance mode

can be entered from either the Idle mode or during the cycle. If the cycle has not yet started,

press the “START” button. To rapid advance to the next step in the wash cycle, push both the

“UP” and “START” buttons at the same time. The display will show an “Ad” (advance) in the

display. The washer will advance to the next bath segment. The water will drain before the

advance will occur and the time displayed may not be accurate.

Notes: - The indicator lights will show to which segment the cycle has been advanced.

- The cycle will continue in rapid advance mode even if the key is turned to “RUN” and/or

removed.

- Rapid advance cannot skip the final 1-minute tumble of the cycle, and the door lock may

remain activated for a couple minutes after the cycle has been completed.

-Chemical 120volt signals will be lost after Rapid advance Mode has been activated until

cycle resets.

To exit the Rapid Advance mode, push and hold the STOP button.

INJECTION SOURCE DETAILS

The washer control may be programmed to send output signals for a chemical injection system.

There is a separate terminal block for connection of the external injection signals. For the

injection sources, program codes 0 through 6 are as shown in the table below.

Dexter

Recommended

Connections

Controller

Programmed

Signals

Injection

Terminal Block

Circuits

Detergent 1 A

Bleach 2 B

Starch 3 C

Sour/Softener 4 D

5 A and B

6 C and D

0 None

Table des matières

Autres manuels Dexter Laundry Rondelle

Dexter Laundry

Dexter Laundry OPL Series Guide de démarrage rapide

Dexter Laundry

Dexter Laundry T-300 VENDED Manuel

Dexter Laundry

Dexter Laundry T-900 Manuel utilisateur

Dexter Laundry

Dexter Laundry WCVD-WN Series Guide de démarrage rapide

Dexter Laundry

Dexter Laundry HIGH SPEED 25LB WASHER Instructions d'installation

Dexter Laundry

Dexter Laundry T-350SWD Manuel utilisateur

Dexter Laundry

Dexter Laundry WCN Series Manuel utilisateur

Dexter Laundry

Dexter Laundry OPL 30 Cycle 200G Express Guide de démarrage rapide

Dexter Laundry

Dexter Laundry WCVD-WN Series Manuel utilisateur

Dexter Laundry

Dexter Laundry T-650 Guide de démarrage rapide

Dexter Laundry

Dexter Laundry T-300 VENDED Manuel utilisateur

Dexter Laundry

Dexter Laundry T1200 Instructions d'installation

Dexter Laundry

Dexter Laundry T350 Manuel utilisateur

Dexter Laundry

Dexter Laundry T-675 EXPRESS PLUS Manuel utilisateur

Dexter Laundry

Dexter Laundry WC Series Guide de démarrage rapide

Dexter Laundry

Dexter Laundry C Series Manuel utilisateur

Dexter Laundry

Dexter Laundry T-900 Guide de démarrage rapide

Dexter Laundry

Dexter Laundry WC 00XA-12EC X Series Manuel utilisateur

Dexter Laundry

Dexter Laundry T-300 VENDED Manuel utilisateur

Dexter Laundry

Dexter Laundry T-400 On-Premise Manuel utilisateur

Dexter Laundry

Dexter Laundry WCVD Series Guide de l'administrateur

Dexter Laundry

Dexter Laundry T450 Express Manuel utilisateur

Dexter Laundry

Dexter Laundry O Series Guide de démarrage rapide

Dexter Laundry

Dexter Laundry N-Series Manuel utilisateur

Manuels Rondelle populaires d'autres marques

Tricity Bendix

Tricity Bendix AW 1000 W Guide produit

Panasonic

Panasonic NA-F60L5WRB Manuel utilisateur

GE WSLP1500 Manuel

Electrolux

Electrolux EWF1284EDW Manuel utilisateur

Bosch

Bosch WAN2829BSN Manuel utilisateur

LG TV2516DV3B Manuel utilisateur

LG TH2517DSAV Manuel utilisateur

VESTEL

VESTEL CMH-XL 7510 TE Manuel utilisateur

AEG

AEG 74335 Manuel d'utilisation

Johnson

Johnson JWF721A Manuel utilisateur

Beko

Beko WTE7604XLW0 Manuel utilisateur

Danby

Danby DTT100A1WDB Instructions de montage

Amica

Amica WA 14 Ex Manuel utilisateur

Daewoo

Daewoo DWD-F1222 Manuel utilisateur

Bosch

Bosch WAS28461AU Manuel utilisateur

Miele

Miele PW 6080 Vario Manuel utilisateur

Finlux

Finlux FLX108CF220 Manuel utilisateur

Whirlpool

Whirlpool 3LBR5132AN0 Manuel utilisateur