DeWalt Emglo D55151 Manuel utilisateur

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, cont&ctenos.

iNSTRUCTiON MANUAL

GUIDE D'UTILiSATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO Y POLIZA

DE GARANTiA. ADVERTENClA: LI_ASE ESTE INSTRUCTIVO ANTES

DE USAR EL PRODUCTO.

D55151, D55152, D55153, D55155

Contractor's Electric 4 Gallon Hand Carry Air Compressor

Compresseurs d'air portatifs 61ectriques de 4 gallons de classe entrepreneur

Compresor de aire portatil electrico de 4 galones para contratistas

Air Compressor

A. On/Off Switch

B. Air Tank Pressure Gauge

C. Regulated Pressure Gauge

D. Pressure Regulator

E. Quick Connects (if equipped)

F. Check Valve

G. Safety Valve

H. Air Tank Drain Valve

I. Power Cord Wrap

J. Pressure Switch

K. Pump Oil Dipstick

L. Pump Oil Drain Plug

M. Motor Reset

N. Air Intake Filter

FIG. 1 BNOT A

STEP DB

Specifications

MODEL D55155

D55152

65 Ibs. (29.5 kg)

16.0" (406.4 ram)

18.0" (457.2 ram)

4.0 (15.1 liters)

95 PSI (655 kPa)

125 PSI (861.8 kPa)

3.8

1.1 HP (continuous)

120V/14 A/60 Hz.

3450

15 Amp

WEIGHT 56 Ibs. (25.4 kg) 58 Ibs. (28.3 kg) 61 Ibs. (27.7 kg)

HEIGHT 16.75" (425.5 mm) 16.75" (501.7 mm) 12.5" (317.5 mm)

WIDTH 18.0" (457.2 mm) 18.0" (457.2 mm) 21.75" (552.5 mm)

LENGTH 15.0 (381 mm) 15.0 (381 mm) 21.75" (552.5 mm)

AIRTANK CAPACITY (GALLONS) 4.0 (15.1 liters) 4.0 (15.1 liters) 4.0 (15.1 liters)

APPROX CUT=IN PRESSURE 95 PSi (655 kPa) 95 PSi (655 kPa) 100 PSi (689.5 kPa)

APPROX. CUT=OUT PRESSURE 125 PSi (861.8 kPa) 125 PSi (861.8 kPa) 125 PSi (861.8 kPa)

SCFM @ 100 PSI (689.5 kPa) 3.2 3.8 4.5

MOTOR 1.1 HP (continuous) 1.1 HP (continuous) 1.2 HP (continuous)

Volts/Amps/Hertz 120V/12.5 A/60 Hz. 120V/14 A/60 Hz. 120V/15 A/60 Hz.

RPM 3450 3450 3450

Minumum Branch Circuit 15 Amp 15 Amp 15 Amp

Requirement

PUMP OIL CAPACITY 6 oz. (177.4 ml) 12 oz. (354.9 ml) 12 oz. (354.9 ml) 4 oz. (118.3 ml)

Hot Surfaces PUMP

FIG.2 CYLNDER

AND

OUTLET TUBE CHECK /

VALVE /CHECK

OUTLET TUBE VALVE

Definitions: Safety Guidelines

The definitions below describe the level of severity

for each signal word. Please read the manual and

pay attention to these symbols.

`&DANGER: Indicates an imminently hazardous

situation which, ff not avoided, wifl result in death

or serious injury.

AWARNING: Indicates a potentially hazardous

situation which, ff not avoided, could result in death

or serious injury.

,&CAUTION: Indicates a potentially hazardous

situation which, ff not avoided, may result in minor

or moderate injury.

CAUTION: Used without the safety alert symbol

indicates a potentially hazardous situation which, ff

not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT

THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT:

I=800=4=DEWALT (1-800=433=9258)

Important Safety Instructions

_, WARNING: Do not operate this unit until you read and understand

this instruction manual for safety, operation and maintenance

instructions.

AWARNING: Some dust created by power sanding, sawing, grind-

ing, drilling, and other construction activities contains chemicals

known to the State of California to cause cancer, birth defects or other

reproductive harm. Some example of these chemicals are:

* lead from lead-based paints

* crystalline silica from bricks and cement and other masonry

products

* arsenic and chromium from chemically-treated lumber

Your risk from these exposures varies, depending on how often

you do this type of work. Toreduce your exposure to these chemi-

cals: work in a weft ventilated area, and work with approved safety

equipment, always wear OSHA/MSHA/NIOSH approved, properly

fitting face mask or respirator when using such tools.

When using air tools, basic safety precautions should always be fol-

lowed to reduce the risk of of personal injury,

_WARNING: This product contains chemicals, including lead,

known to the State of California to cause cancer, and birth

defects or other reproductive harm. Wash hands after handling.

SAVE THESE INSTRUCTION

,t_DANGER: RISK OF EXPLOSION OR FIRE

WHAT CAN HAPPEN HOWTO PREVENT iT

• It is normal for electrica! _ Always operate the compres_

contacts within the motor Sorin a well ventilated area

and pressure switch to free of combustible materials,

spark, gasoline, or solvent vapors.

• If electrical sparks from • If spraying flammable materi-

compressor come into con- als, locate compressor at

tact with flammable vapors, east 20 feet 16.1m) away

they may ignite, causing fire from spray area. An addi-

or explosion, tional length of hose may be

required.

- Store flammable materials q

a secure location away from

compressor.

• Restricting any of the com- • Never place objects against

pressor ventilation openings or on top of compressor

will cause serious overheat- • Operate compressor in

ing and could cause fire. an open area at least 12"

(30.5 cm) away from any

wall or obstruction that would

restrict the flow of fresh air to

the ventilation openings.

•Operate compressor in a

clean, dry well ventilated area.

Do no_operate unit indoors or

in any confined area.

Unattended operation of

this product could result in

personal injury or property

damage. To reduce the risk

of fire, do not allow the

compressor to operate unat-

tended.

• Always remain in attendance

with the product when it is

operating.

• Always turn off and unplug

unit when not in use.

ADANGER: RISK TO BREATHING (ASPHYXIATION)

WHAT CAN HAPPEN HOWTO PREVENTIT

, The compressed air directly - Air obtained directly from the

from your compressor is not compressor should never

safe for breathing. The air be used to supply air for

stream may contain carbon human consumption. Inorder

monoxide, toxic vapors, to use air produced by this

or solid particles from the compressor for breathing

air tank. Breathing these suitable filters and in-line

contaminant's can cause safety equipment must be

serious injury or death, properly installed. In-line

filters and safety equipment

used in conjunction with the

compressor must be capable

of treating air to all applicable

local and federal codes prior to

human consumption

Sprayedmaterialssuchas

paint,paintsolvents,paint

remover,insecticides,weed

killers,maycontainharmful

vaporsandpoisons.

Workinanareawithgood

crossventilation.Readand

followthesafetyinstructions

providedonthelabelorsafety

datasheetsforthematerials

youarespraying.Alwaysuse

certifiedsafetyequipment:

OSHA!MSHA/NIOSH

respiratoryprotectiondesigned

forusewithyourspecific

application.

_&DANGER:RISK OF INJURY OR PROPERTY DAMAGE WHEN

TRANSPORTING OR STORING

WHAT CAN HAPPEN HOWTO PREVENTIT

o Oil can leak or spill and could - Always place compressor

result in fire or breathing on a protective mat when

hazard; serious injury or transporting to protect against

death can result.Oil leaks will damage to vehicle from leaks.

damage carpet, paint or other Remove compressor from

surfaces invehicles or trailers, vehicle immediately upon arrival

at your destination. Always keep

compressor leveland never lie

on its side.

_&WARNING: RISK OF BURSTING

AirTank: The air tank on your Air Compressor is designed and may

be UM coded (for units with air tanks greater than 6 inch diameter)

according to ASME Section VIII, Div. 1 rules. All pressure vessels

should be inspected once every two years.To find your state pressure

vessels inspector, look under the Division of Labor and Industries in

the government section of a phone book or call 1-800-4-DEWALT for

assistance.

The following conditions could lead to a weakening of the air tank,

and result in aviolent air tank explosion:

WHAT CAN HAPPEN HOWTO PREVENT IT

Failure to properly drain _ Drain air tank daily or after

each use. If air tank develops

a leak. replace it immediately

with a new air tank or replace

the entire compressor.

Modifications or attempted - Never drill into. weld, or make

repairs to the air tank, any modifications to the air

tank or its attachments. Never

attempt to repair a damaged or

leaking air tank. Replace with a

new air tank.

•• The airtank is designed

to withstand specific

operating pressures. Never

make adjustments or parts

substitutions to alter the factory

set operating pressures.

Unauthorized modifications

to the safety valve or any

other components which

control air tank pressure.

condensed water from

air tank. causing rust and

thinning of the steel air tank.

Attachments&accessories:

Exceeding the pressure • Follow the equipment

rating of air tools, spray guns. manufacturers

air operated accessories, recommendation and never

tires, and other inflatables exceed the maximum

can cause them to explode allowable pressure rating

or fly apart, and could result of attachments. Never use

in senous injury, compressor to inflate small

low pressure objects such

as children's toys, footballs,

basketballs, etc.

AWARNING: RiSK OF ELECTRICAL SHOCK

• Repairs attempted by

unqualified personnel can

result in serious injury or

death by electrocution.

WHAT CAN HAPPEN HOWTO PREVENT iT

" Youiair c0mpress0r is .Never operate the

powered bYelectricity, compressor outdoors when it

Like any other electrically is raining 0r in wet conditions.

powered device, !fit iS not ,, Never operate comPressor

used proper!y it may cause with protective covers

electric shock, removed or damaged.

• Any electrical wiring or

repairs required on this

product should be performed

by a DEWALT factory

service center or a DEWALT

authorized service center in

accordance with national and

local electrical codes.

-Electrical Grounding: = Make certain that the

Failure to provide adequate electrical circuit to which the

grounding to this product compressor is connected

could result in serious injury provides proper electrical

or death from electrocution, grounding, correct voltage

See Grounding and adequate fuse protection.

instructions under

Installation.

AWARNING: RISK FROM FLYING OBJECTS

WHAT CAN HAPPEN

• The compressed air stream

can cause soft tissue

damage to exposed skin and

can propel dirt, chips, loose

particles, and small objects

at high speed, resulting in

property damage or personal

injury.

HOWTO PREVENT IT

• Always wear certified safety

equipment: ANSI Z87.1 eye

protection (CAN/CSA Z94.3)

with side shields when using

the compressor.

• Never point any nozzle or

sprayer toward any part of

the body or at other people or

animals.

Always turn the compressor off

and bleed pressure from the

air hose and air tank before

attempting maintenance,

attaching tools or accessories.

AWARNING:RiSK OF HOT SURFACES

WHAT CAN HAPPEN HOWTO PREVENT JT

•Touching exposed metal -Never touch any exposed

such as the compressor metal parts on compressor

head. engine head, engine during or immediately after

exhaust or outlet tubes, can operation. Compressor will

result in serious burns, remain hot for several minutes

after operation.

• Do not reach around

protective shrouds or attempt

maintenance until unit has

been allowed to cool.

_, WARNING: RiSK FROM MOVING PARTS

WHAT CAN HAPPEN HOWTO PREVENT IT

Moving parts such as the

pulley, flywheel, and belt can

cause serious injury ifthey

come into contact with you or

your clothing.

• Never operate the compressor

with guards or covers which

are damaged or removed.

• Keep your hair,clothing, and

gloves away from moving

parts. Loose clothes, jewelry,

or long hair can be caught in

moving parts.

• Air vents may cover moving

parts and should be avoided

as well.

-Attempting to operate o Any repairs required on this

compressor with damaged or product should be performed

missing parts or attempting by a DEWALTfactory

to repair compressor with service center or a DEWALT

protective shrouds removed authorized service center.

can expose you to moving

parts and can result in

serious injury.

AWARNING: RISK OF UNSAFE OPERATION

WHAT CAN HAPPEN HOWTO PREVENT IT

Unsafe operation of your air

compressor could lead to seri-

ous injury or death to you or

others.

Review and understand all

instructions and warnings in

this manual.

• Become familiar with the

operation and controls of the

air compressor.

• Keep operating area clear of all

persons, pets, and obstacles.

• Keep children away from the

air compressor at all times.

• Do not operate the product

when fatigued or under the

influence of alcohol or drugs.

Stay alert at all times.

• Never defeat the safety fea-

tures ofthis product.

• Equipareaofoperationwitha

fireextinguisher.

• Donotoperatemachinewith

missing,broken,orunautho-

rizedparts.

WARNING: RiSK OF FALLING

WHAT CAN HAPPEN HOWTO PREVENTIT

A portable compressor _ Always operate compressor

can fall from a table, in a stable secure position to

workbench, or roof causing prevent accidental movement

damage to the compressor of the unit. Never operate

and could result in serious compressor on a roof or

njury or death to the other elevated position. Use

operator, additio nal air hose to reach

high locations.

ACAUTION: RISK FROM NOISE

WHAT CAN HAPPEN HOWTO PREVENT IT

Under some conditions and • Always wear certified safety

duration of use, noise from equipment: ANSI S12.6

this product may contribute (S3.19) hearing protection.

to hearing loss.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

FEATURES (Fig. 1)

ON/OFF SWITCH

Place this switch (A) in the ON position to

provide automatic power to the pressure

switch and OFF to remove power at the

end of each use.

PRESSURE SWITCH

The pressure switch (J) automatically

starts the motor when the air tank pres-

sure drops below the factory set cut-in

pressure. It stops the motor when the air tank pressure reaches the

factory set cut-out pressure.

PRESSURE RELEASE VALVE

The pressure release valve located on the side of the pressure switch,

is designed to automatically release compressed air from the compres-

sor head and the outlet tube when the air compressor reaches cut-out

pressure or is shut off. The pressure release valve allows the motor to

restart freely.When the motor stops running, air will be heard escaping

from this valve for a few seconds. No air should be heard leaking when

the motor is running or after the unit reaches cut-out pressure.

SAFETY VALVE

If the pressure switch does not shut off the air compressor at its

cut-out pressure setting, the safety valve (G) will protect against

high pressure by popping out at its factory set pressure (slightly

higher than the pressure switch cut-out setting).

CHECK VALVE

When the air compressor is operating, the check

valve (F) is open, allowing compressed air to enter

the air tank. When the air compressor reaches cut-

out pressure, the check valve closes, allowing air

pressure to remain inside the air tank.

TANKPRESSUREGAUGE

Thetankpressuregauge(B)indi-

catesthereserveairpressurein

thetank.

OUTLETPRESSUREGAUGE

Theoutletpressuregauge(C)

indicatestheairpressureavailable

attheoutletsideoftheregulator.

Thispressureiscontrolledbytheregulatorandisalwayslessthan

orequaltothetankpressure.

REGULATOR

Theregulator(D)controlstheairpressureshownontheoutlet

pressuregauge.Turnregulatorknobclockwisetoincreasepres-

sureandcounterclockwisetodecreasepressure.

UNIVERSALQUICKCONNECTBODIES(IFEQUIPPED)

Theuniversalquickconnectbody(E)acceptsthethreemost

popularstylesofquickconnectplugs:Industrial,automotive,and

ARO.Onehandpush-to-connectoperationmakesconnections

simpleandeasy.Thetwoquickconnectbodiesallowtheuseoftwo

toolsatthesametime.

DRAIN VALVE

The drain valve (H) is located at the base

of the air tank and is used to drain conden-

sation atthe end of each use. See Draining

Air Tank under Maintenance.

COOLING SYSTEM

This compressor contains an advanced design cooling system.

It is normal for this fan to blow air through the vent holes in large

amounts. The cooling system is working when air is expelled.

AIR COMPRESSOR PUMP

The pump compresses air into the air tank. Working air is not

available until the compressor has raised the air tank pressure

above that required at the air outlet.

MOTOR OVERLOAD PROTECTOR

This motor has a manual thermal overload

protector. If the motor overheats for any

reason, the overload protector will shut off

the motor. The motor must be allowed to

cool down before restarting. To restart:

1. Ensure the On/Off switch (A) is in the

OFF position.

2. Allow the motor to cool.

3. Depress the reset button (M) on the

motor.

OIL DIPSTICK

The oil dipstick (K) indicates the amount of oil in the pump. Check

pump oil daily, see Compressor Pump Oil under Maintenance.

AIR iNTAKE FILTER

The filter (N) is designed to clean air entering the pump. To ensure

the pump continually receives a clean, cool, and dry air supply the

filter must always be clean and the filter intake must be free from

obstructions.

INSTA£LATION

Assembly

iNSTALLING HOSES

WARNING: Risk of unsafe operation. Firmly grasp hose in hand

when installing or disconnecting to prevent hose whip.

Autres manuels pour Emglo D55151

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels DeWalt Compresseur d'air

DeWalt

DeWalt D55690 Manuel utilisateur

DeWalt

DeWalt D55171 Manuel utilisateur

DeWalt

DeWalt Emglo D55152 Manuel utilisateur

DeWalt

DeWalt D2002M Manuel utilisateur

DeWalt

DeWalt D55168 Manuel utilisateur

DeWalt

DeWalt DXCM301 Manuel utilisateur

DeWalt

DeWalt DXCMV7518075 Manuel utilisateur

DeWalt

DeWalt D55672 Manuel utilisateur

DeWalt

DeWalt D55180T Manuel utilisateur

DeWalt

DeWalt DWFP55120 Manuel utilisateur

DeWalt

DeWalt DXCMH1608WB Manuel utilisateur

DeWalt

DeWalt D2002M Manuel utilisateur

DeWalt

DeWalt D55371 Manuel utilisateur

DeWalt

DeWalt D55141-CA Manuel utilisateur

DeWalt

DeWalt D55250 Manuel utilisateur

DeWalt

DeWalt D55271 Manuel utilisateur

DeWalt

DeWalt DXCM024-0393 Manuel utilisateur

DeWalt

DeWalt DXCMV5018055 Manuel utilisateur

DeWalt

DeWalt DXCM603 Manuel utilisateur

DeWalt

DeWalt DWFP55126 Manuel utilisateur

DeWalt

DeWalt D55270-1 Manuel utilisateur

DeWalt

DeWalt D55168 Manuel utilisateur

DeWalt

DeWalt DXCM804 Manuel utilisateur

DeWalt

DeWalt DXCMSAC260 Manuel utilisateur

Manuels Compresseur d'air populaires d'autres marques

Sparmax

Sparmax DC-25XR Manuel utilisateur

KAESER

KAESER M122 Manuel utilisateur

GMC

GMC GAC1500 Manuel utilisateur

Briggs & Stratton

Briggs & Stratton Air Compressor Manuel utilisateur

Fini

Fini F3GST2TK Manuel utilisateur

Industrial Air

Industrial Air CP1580325 Manuel de programmation

Campbell Hausfeld

Campbell Hausfeld RP3300 Guide de démarrage rapide

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Manuel utilisateur

Hitachi

Hitachi EC99S Manuel de l'opérateur

Parkside

Parkside PKO 270 A1 Manuel utilisateur

Sullair

Sullair 185 Manuel utilisateur

Clas Ohlson

Clas Ohlson QIE-ZTH-15 Manuel utilisateur

Ferm

Ferm CRM1046 Manuel utilisateur

BE AC153 Manuel utilisateur

RIDGID

RIDGID OF25150A Manuel utilisateur

Johnson Controls

Johnson Controls QUANTUM LX Manuel

Sears

Sears Craftsman 919.167463 Manuel utilisateur

Ring Automotive

Ring Automotive RAC700 Manuel utilisateur