Devanco Canada Marantec M3-2312 Manuel utilisateur
Transmitters
Instructions
for models: M3-2312, M3-2314, M3-3313
FEATURES
Mini (2- or 4-channel)
Micro (3-channel), the smallest transmitter of its kind.
3. Battery Replacement (Figure 2)
Open the transmitter by using small coin.
The installation of the battery for Mini and Micro is the same.
When replacing batteries follow the steps below:
Close the transmitter.
Note: Replace batteries with same type only.
Insert a 3V battery (type CR2032) as shown.
1. Using the Transmitter
2. Transmitter Mounting (Figure 1)
Mounting Plate (fig. 1A)
The mounting plate enables you to mount the transmitter easily
to the wall or other area.
Secure the mounting plate to area using screw and anchor
(not provided).
Visor Clip (fig. 1B)
Key Ring Attachment (fig. 1C)
The transmitters can be convenietly mounted on the wall (fig.
1A) using the mounting plate (optional) or inside your car using
the visor clip (fig. 1B). These two mounting alternatives (fig. 1A
and fig. 1B) are available with Mini models only. The Micro can
be used with the key ring attachment (fig. 1C).
Slide the transmitter into the mounting plate, which will hold
it firmly in place.
Open the Micro by using small coin.
Snap in the key ring attachment.
Close the transmitter.
To open or close garage door, press and hold the button (Mini
and Micro transmitters have indicator lights). When garage
door begins to move release button.
To stop the garage door during travel, press and hold button
until door stops, then release button.
To continue the garage door travel after stopping it, press and
hold the button. Press button once, the door will travel in the
opposite direction.
The visor clip allows for easy mounting of the transmitter to a
car visor.
The key ring attachment permits easy mounting of the Micro
to a key ring.
Snap visor clip into transmitter.
Note: If you do not need the visor clip, install the visor
compartment cover.
Figure 2. Battery Compartment
Coin
Battery
Figure 1. Mounting Plate & Visor Clip
fig. 1A
fig. 1B
fig. 1C Key Ring Attachment for Micro Transmitter
A family of state-of-the-art transmitters, each transmitter is
custom encoded and ergonomically designed to be an integral
part of your garage door opener system, with two styles to suit
your personal preference:
Visor Compartment
Cover
Visor Clip
Key Ring
Attachment
All transmitters come with batteries already installed.
Mounting Plate
(optinal)
For more information, please visit www.devancocanada.com or call toll free at 855-931-3334
4. Multiple Transmitters (Figure 3)
Each transmitter comes factory programmed with random
codes. 2-channel transmitters have 2 different random codes,
one per button, 3-channel transmitters have 3 different random
codes and 4-channel transmitters have 4 different random
codes, one per button. Transmitters that are purchased
separately as accessories have random codes that must be
changed in order to match the code of the "active" transmitter,
which you are alredy using. Below are instructions for
transferring an active code from a button on one transmitter to a
button of your choice on another transmitter.
Connect the transmitter with active code to the new
transmitter using the programming connector (fig. 3A).
Press and hold the selected channel button on the transmitter
with the active code (fig. 3B). The light in the transmitter
illuminates.
Press and hold the respective channel button on the new
transmitter (fig. 3C). The light in the transmitter initially starts
blinking and then illuminates continuously after 1-2 sec. Code
transfer is completed.
Programming connector can be removed and both transmitters
can now b e used to operate the same door.
Note: For multi-button transmitters, be sure to carry out this
procedure for all the buttons you desire to use.
5. Changing the Code on Transmitters (Figure 4)
The transmitter factory preset code can be changes as follows:
Connect the programming connector into the lateral socket of
the transmitter to change the code.
Short one of the outer pins of the programming connector with
the middle pin.
Press and hold the respective channel button. The light will blink
rapidly for approx. 5 sec. Release the button after the light
illuminates continuously. Then remove the programming
connector.
Note: For multi-button transmitters, be sure to carry out this
procedure for all the buttons you desire to use.
Figure 3. Multiple Transmitters-Code Transfer
Transmitter with active Code
new Transmitter
Programming
Connector
fig. 3A
fig. 3B
fig. 3C
Figure 4. Code Changing
FCC Certified: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user´s authority to operate the equipment.
65895 2003 All rights reserved. 05/03 ©
Transmitters
Instructions
(continued)
HOW TO ORDER
REPAIR PARTS
DEVANCO CANADA
19192 HAY ROAD, UNIT Q
SUMMERSTOWN, ON K0C 2E0
TOLL FREE: 855-931-3334
www.devancocanada.com
WHEN ORDERING REPAIR PARTS
PLEASE SUPPLY THE
FOLLOWING INFORMATION:
3PART NUMBER
3DESCRIPTION
3MODEL NUMBER
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Devanco Canada Émetteur
Manuels Émetteur populaires d'autres marques
Dejero
Dejero EnGo 3x Manuel utilisateur
Rosemount
Rosemount 4600 Manuel utilisateur
Speaka Professional
Speaka Professional 2342740 Manuel utilisateur
trubomat
trubomat GAB 1000 Manuel utilisateur
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manuel utilisateur
Rondish
Rondish UT-11 Manuel utilisateur
