Dell EMC PowerEdge T440 Manuel utilisateur
1
PowerEdge T440 System
LTO8 Tape Backup Device
Simple Operation Manual
Dell Technologies, Inc.
Nippon COMSYS Corporation
03-November-2020
2
Version Control
Version
Date
Created
Remarks
1
2019.3.12
Nippon COMSYS Corporation
First edition
1.1
2020.9.10
Dell Technologies, Inc.
Equipment image, reference
Information added
3
Front view of T440 device
USB3.0 Port
For attaching the
USB Disk Drive
(high-speed mode)
Power Button
LTO8 Drive with Eject Button
4
Rear view of T440
Ethernet 2 Ports for Network services
By default, these ports are also used
for DHCP Client settings.
iDRAC Remote Management Port
(management only)
By default, the port is also used
for DHCP client settings.
No access to server services ex.
CIFS / NFS etc.
5
mac address confirmation method
You can check the mac address of the NIC with the ‘ifconfig’ command.
* Please note that the output below may differ depending on the environment (see eth0, eth1,
as examples).
# ifconfig -a
eth0 Link encap:Ethernet(1) HWaddr 00:80:90:44:08:11(2)
inet addr:192.168.1.11(3) Bcast:192.168.1.255(4) Mask:255.255.255.0(5)
inet6 addr: fe80::3199:ff:fe01:3762/64 Scope:Link(6)
UP(7) BROADCAST(8) RUNNING(9) MULTICAST(10) MTU:1500(11)
Metric:1(12)
RX packets:583312 errors:0 dropped:0 overruns:0 frame:0(13)
TX packets:28344 errors:0 dropped:0 overruns:0 carrier:0(13)
collisions:0 txqueuelen:100(13)
RX bytes:4987886272 (4.9 GB) TX bytes:50440257 (50.4 MB)(14)
eth1 Link encap:Ethernet HWaddr 00:80:00:48:AA:88
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:3924 Metric:1
RX packets:16 errors:0 dropped:0 overruns:0 frame:0
TX packets:16 errors:0 dropped:0 overruns:0 carrier:0
6
Backup / Restore from the USB disk mount to LTO8 tape:
i. Attach the USB hard disk drive to the computer.
ii. Confirm that filesystem has been mounted ( you can use gnome ‘nautilus’ file system
manager.) #By default, Cent OS 7 has automount feature.
iii. /dev/nst0 device is the LTO 8 drive.
iv. Now you can backup files on the mounted drive to LTO8 tape using ‘tar cvf ’command.
v. You can access the LTO8 tape drive by using ‘mt’ command.
vi. When restoring file(s) from the LTO8 tape to the USB disk, you must move properly the
tape head using the ‘mt’ command.
vii. *To restore a tar archive to the USB disk, you should use ‘tar xvf’ command.
*caution, this will overwrite the existing data on the hard drive.
7
Tape device
Tape devices are recognized as /dev/st0 and /dev/nst0.
/dev/st0 automatically rewinds the tape to the beginning after a read / write operation.
/dev/nst0 moves to the beginning of the next file after a read / write operation.
Check the tape status
Check the tape status with the ‘mt’ command:
# mt -f /dev/nst0 status
SCSI 2 tape drive:
File number = 4, block number = 0, partition = 0.
Tape block size 0 bytes. Density code 0x46 (LTO-4).
Soft error count since last status = 0
General status bits on (81010000):
EOF ONLINE IM_REP_EN
#
Tape operation
To rewind the tape, specify rewind with the ‘mt’ command:
# mt -f /dev/nst0 rewind
To move the tape to the beginning of the next file at the current position, specify fsf 1 with the
‘mt’ command:
# mt -f /dev/nst0 fsf 1
To move the tape to the beginning of the file at the current position, specify bsfm 1 with the
‘mt’ command:
# mt -f /dev/nst0 bsfm 1
8
To move the tape to the beginning of the file immediately before the file at the current
position, specify bsfm 2 with the ‘mt’ command:
# mt -f /dev/nst0 bsfm 2
File writing with ‘tar’ command
Specify /dev/st0 or /dev/nst0 as the write destination with the tar command:
# tar cvf /dev/nst0 <file name> <file name>…
File extraction with ‘tar’ command
Move to the beginning of the target file and read from /dev/st0 or /dev/nst0 with the tar
command:
# tar xvf /dev/nst0
Tape drive cleaning
When cleaning is required, "C" will be displayed on the character display. Insert only the
cleaning cartridge into the drive. When cleaning is complete, the cleaning cartridge will be
ejected.
ファイル 1
ファイル 2
ファイル 3
EOF
現在位置
rewind
bsfm 1
fsf 1
bsfm2
EOF
EOF
9
Reference URL
T440 Owner’s Manual
https://topics-cdn.dell.com/pdf/poweredge-t440_owners-manual10_en-us.pdf
T440 Japanese Manual
https://topics-cdn.dell.com/pdf/poweredge-t440_owners-manual10_ja.pdf
TAG NUMBER is 777CHV2
You can access DELL’S support resources new device driver etc. at the following URL:
https://www.dell.com/support/home/en-us/product-support/servicetag/0-
WDJVK3YxYmJ6N1BHT0QxK1lRK1lmQT090/overview
Autres manuels pour EMC PowerEdge T440
2
Table des matières
Autres manuels Dell Serveur
Dell
Dell PowerEdge R510 Guide de démarrage rapide
Dell
Dell PowerEdge 4600 Manuel utilisateur
Dell
Dell PowerEdge R630 Manuel utilisateur
Dell
Dell PowerEdge 1950 Manuel technique
Dell
Dell PowerEdge R715 Guide de démarrage rapide
Dell
Dell Precision Workstation 350 Manuel technique
Dell
Dell PowerEdge C6105 Manuel utilisateur
Dell
Dell PowerEdge UPS 500T Manuel utilisateur
Dell
Dell PowerEdge T710 Manuel utilisateur
Dell
Dell PowerEdge M830 Manuel utilisateur
Dell
Dell XC6320 Manuel utilisateur
Dell
Dell PowerEdge T20 Manuel utilisateur
Dell
Dell PowerEdge 4600 Manuel technique
Dell
Dell PowerEdge C410X Manuel de la liste des pièces
Dell
Dell CX700 Manuel utilisateur
Dell
Dell PowerEdge 4200 Series Manuel utilisateur
Dell
Dell PowerEdge T620 Manuel utilisateur
Dell
Dell PowerEdge UPS 500T Manuel utilisateur
Dell
Dell PowerEdge XR7620 Manuel
Dell
Dell Precision FX100 Manuel utilisateur
