Dell Wyse Z90D7 Manuel utilisateur

Installation Guide

Dell® Wyse Z Class Conversion to WES7p

Wyse USB Firmware ToolTM Release 1.20.0.1

Products: Z90D7, Z90S7, Z90DE7, Z90DW, Z90SW

Issue: 021214

PN: 883887-37L Rev. A

This manual and the software and firmware described in it are copyrighted. You may not reproduce, transmit,

transcribe, store in a retrieval system, or translate into any language or computer language, in any form or by

any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, any part of this

publication without express written permission.

End User License Agreement (“License”)

A copy of the End User License Agreement is included in the software and provided for your reference only.

The License at http://www.wyse.com/license as of the purchase date is the controlling licensing agreement. By

copying, using, or installing the software or the product, you agree to be bound by those terms.

Trademarks

The Dell, Wyse, and PocketCloud logos and Wyse and PocketCloud are trademarks of Dell Inc. Other product

names mentioned herein are for identification purposes only and may be trademarks and/or registered

trademarks of their respective companies. Specifications subject to change without notice.

You acknowledge that the Software is of U.S. origin. You agree to comply with all applicable international and

national laws that apply to the Software, including the U.S. Export Administration Regulations, as well as

end-user, end-use and country destination restrictions issued by U.S. and other governments. For additional

information on exporting the Software, see http://www.microsoft.com/exporting.

Ordering Information

For availability, pricing, and ordering information in the United States and Canada, call 1-800-438-9973 or visit

us at Dell.com. In all other countries, contact your sales representative.

Contents

1 Introduction 1

Kit Contents 1

Kit Warranty 2

Overview 2

Dell Technical Support 2

Related Documentation and Services 2

Dell Online Community 2

2 Installing Z Class Flash 3

Requirements 3

Procedures 3

3 Installing WES7p Firmware 7

Requirements 7

Procedures 8

Troubleshooting 13

USB Keys - Troubleshooting Boot Issues 13

SanDisk Cruiser Flash Drives - Troubleshooting Partition Issues 13

iv Contents

This page intentionally blank.

1Introduction

This guide provides step-by-step instructions to use Wyse USB Firmware Tool to

convert the following Wyse Z class thin clients to WES7p:

•Z90D7

•Z90S7

•Z90DE7

•Z90DW

•Z90SW

CAUTION: WES7p firmware requires Z class thin clients to have a minimum of 8 GB

Flash and 4 GB RAM (16 GB Flash and 4 GB RAM is recommended).

TIP: After converting your thin clients, obtain any available firmware update at

http://www.wyse.com/serviceandsupport/support/downloads.asp.

Kit Contents

The conversion kit can include:

•Conversion Software Assembly DVD-ROM

•Flash module (16 GB)

•Wyse Conversion Labels (you must attach a Wyse label to each converted thin

client)

•Microsoft License Labels (you must attach a COA label to each converted thin client)

Figure 1 Kit contents (items may look different or not be included in your kit)

The Conversion Software Assembly DVD-ROM contains:

•A PDF of this Reference Guide

•Wyse USB Firmware Tool Release 1.20.0.1

•Z Class WES7p Conversion Image folder containing the following files:

·bios.img

·commandsXml.xml

·initrd.pxe

·Merlin.log

2Chapter 1

·mbr.img

·par1.img

·par2image1.img

·par2image2i.img

·vmlinuz

Kit Warranty

The warranty on the hardware component of this kit assumes the remaining months of

warranty of the thin client in which it is installed, or for 90 days, whichever is greater.

Installation of this kit will not void the factory warranty, however the user will be

responsible for damage due to improper installation.

Overview

To convert your Z class thin clients to WES7p:

1. (Optional) If you need to perform a hardware installation (install new flash),

complete "Installing Z Class Flash."

2. (Required) Complete "Installing WES7p Firmware."

Dell Technical Support

To access Dell technical resources, visit http://www.wyse.com/support. If you still have

questions, you can submit your questions using the Self-Service Center at

http://support.wyse.com/selfservice.html or call Customer Support at 1-800-800-9973

(toll free in U.S. and Canada). Hours of operation are from 6:00 A.M. to 5:00 P.M. Pacific

Time, Monday through Friday.

To access international support, visit http://www.wyse.com/global.

Related Documentation and Services

Fact Sheets containing the features of hardware products are available on the Dell Web

site. Go to http://www.wyse.com/products and use the Cloud clients tab to locate and

download the Fact Sheet for your hardware product.

Administrator and other documentation for your cloud client model are available at:

http://www.wyse.com/manuals.

Dell Online Community

Dell maintains an online community where users of our products can seek and

exchange information on user forums. Visit the Online Community forums at:

http://community.wyse.com/forum.

2Installing Z Class Flash

This chapter contains information for users of Wyse Z class thin clients who must

install new flash. If you are installing firmware only, you can skip this chapter and

proceed to "Installing WES7p Firmware."

Requirements

•Small Phillips screwdriver

WARNING: Flash modules may be susceptible to damage by Electro-Static Discharge

(ESD). All industry-standard cautions should be followed to avoid ESD. Before you

remove or install a module, touch any metal part of the chassis and keep that contact

with the chassis during the installation process.

Procedures

CAUTION: Follow all precautions listed in the Quick-Start Guide that came with your

thin client for disconnecting and reconnecting the thin client.

1. Perform a proper shutdown of the thin client by closing all files and ending your

session, and then pressing the power button to turn off the thin client.

2. Unplug the power cord and power adapter, and remove any other cables from the

thin client, and detach the vertical foot.

3. Position the thin client horizontally, where the side with four flat screws is facing

downward. Using the Phillips Screwdriver remove the two screws from either end

near the back panel, and then remove the three screws from the cover along the

back panel edge, as shown in Figure 2.

Figure 2 Removing the cover screws

4Chapter 2

4. Place your thumbs on the top surface above where the end screws were removed.

With a continuous motion, push firmly downward and towards the back panel

(pushing down unlatches the hooks under the cover). The cover will shift

approximate 1/4 inch to hang over the back panel, as shown in Figure 3.

Figure 3 Unlatching the cover

5. (a) Grasp the overhanging cover edge and raise the edge

about 1-1/2 inches, and then (b) pull the cover out towards the back panel at the

same angle to free the opposite end of the cover from the remaining hooks, as

shown in Figure 4.

Figure 4 Removing the cover

6. Remove the cover to expose the flash module, as shown in Figure 5.

WARNING: Flash modules may be susceptible to damage by Electro-Static

Discharge (ESD). All industry-standard cautions should be followed to avoid ESD.

Before you remove or install a module, touch any metal part of the chassis and keep

that contact with the chassis during the installation process.

Installing Z Class Flash 5

7. Remove the existing flash module. Locate the flash module and use the Phillips

Screwdriver to remove its retaining screw as shown in Figure 5. Lift the flash module

out of the socket.

Figure 5 Removing the existing flash module

8. Install the new flash module in the reverse order of removing the original flash

module. Carefully screw down its retaining screw until it is secure.

9. (a) Align the cover screw tabs with screw holes and press downward; (b) slide cover

toward the front of the thin client, as shown in Figure 6.

Figure 6 Reattaching the cover

10., Attach the screws in the reverse order as described in step 3.

11.Connect the power cord and power adapter, attach any other cables to the thin

client, and then attach the vertical foot.

CAUTION: Do not turn on the thin client. The thin client is ready to re-image,

however the flash module does not contain an operating system. Turning on power

to your thin client without firmware will display the error message “NO OPERATING

SYSTEM FOUND.”

12.Continue with "Installing WES7p Firmware."

6Chapter 2

This page intentionally blank.

Autres manuels pour Wyse Z90D7

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Dell Serveur

Dell

Dell PowerEdge R910 Manuel technique

Dell

Dell PowerEdge C5125 Manuel utilisateur

Dell

Dell PowerEdge XR4000w Manuel

Dell

Dell PowerEdge M520 Manuel utilisateur

Dell

Dell PowerEdge 650 Mode d’emploi

Dell

Dell PowerEdge T710 Manuel technique

Dell

Dell PowerEdge 8450 Manuel utilisateur

Dell

Dell Force10 MXL Blade Manuel utilisateur

Dell

Dell PowerEdge T20 Manuel utilisateur

Dell

Dell Precision FX100 Manuel utilisateur

Dell

Dell CX700 Manuel utilisateur

Dell

Dell PowerEdge R520 Manuel utilisateur

Dell

Dell PowerEdge systems 6300 Manuel de la liste des pièces

Dell

Dell PowerEdge 6650 Manuel utilisateur

Dell

Dell PowerEdge C8000 Manuel utilisateur

Dell

Dell PowerEdge 2300 Manuel d'installation et d'exploitation

Dell

Dell PowerEdge FC640 Manuel

Dell

Dell PowerEdge 1955 Manuel utilisateur

Dell

Dell S5000 Series Manuel utilisateur

Dell

Dell PowerEdge C8000 Manuel utilisateur

Dell

Dell PowerEdge 1400SC Manuel technique

Dell

Dell EMC PowerEdge T440 Manuel

Dell

Dell Vostro 1400 Instructions de montage

Dell

Dell PowerEdge 2970 Manuel utilisateur

Manuels Serveur populaires d'autres marques

HP AlphaServer ES47 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

HP ProLiant Gen9 Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

HP Integrity rx2600 Guide d'installation

Milestone

Milestone Husky IVO 350T Manuel utilisateur

Planet

Planet NAS-7410 Manuel utilisateur

Lenovo

Lenovo ThinkSystem SR635 V3 Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY BX900 Manuel utilisateur

Asus

Asus RS700DA-E6 PS4 Manuel utilisateur