Dell POWEREDGE M905 Manuel utilisateur

Dell™ PowerEdge™

M905, M805, M605, and M600

Getting Started

With Your System

Začínáme se systémem

Guide de mise en route

Handbuch zum Einstieg

Τα πρώτα βήµατα µε το σύστηµά σας

Rozpoczęcie pracy z systemem

Начало работы с системой

Procedimientos iniciales con el sistema

תכרעמה ע הדובעה תליחת

Dell™ PowerEdge™

M905, M805, M605, and M600

Getting Started

With Your System

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use

of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data

and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury,

or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly

forbidden.

Trademarks used in this text: Dell, the DELL logo, and Dell OpenManage are trademarks of Dell Inc.;

Microsoft, Windows, and Windows Server are either trademarks or registered trademarks of Microsoft

Corporation in the United States and/or other countries; AMD and AMD Opteron are trademarks of

Advanced Micro Devices, Inc.; Intel and Xeon are registered trademarks of Intel Corporation; SUSE

is a registered trademark of Novell, Inc.; Red Hat and Enterprise Linux are registered trademarks of

Red Hat, Inc.; VMware is a registered trademarks of VMware, Inc. in the United States and/or other

jurisdictions.

Other trademarks and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

Model BMX01

May 2008 P/N R431C Rev. A00

Getting Started With Your System 3

System Features

This section describes the major hardware and software features of your

system. It also provides information about other documents you may need

when setting up your system and how to obtain technical assistance.

System Enclosure Features

The M1000e system enclosure (chassis) includes the following features:

Scalability Features

• Support for up to 16 half-height or 8 full-height blades (server modules).

• Support for three layers of I/O fabric, selectable between combinations

of Ethernet, Infiniband, and Fibre Channel modules.

Up to six I/O modules may be installed in the enclosure, chosen from Fibre

Channel switches, Fibre Channel passthroughs, Infiniband switches,

Ethernet switches, and Ethernet passthrough modules.

Reliability Features

• Nine redundant, hot-pluggable system fan modules.

• Three 2360-watt, hot-pluggable power supplies and three power supply

blanks, or six 2360-watt, hot-pluggable power supplies. (Three power

supplies provide power to the system; adding three additional power

supplies provides 3+3 redundancy.)

NOTICE: Power supplies can only connect to a power distribution unit (PDU).

They cannot connect directly to an electrical outlet.

NOTICE: The system enclosure requires a 200-240V power source.

4Getting Started With Your System

Systems Management Features

• A Chassis Management Controller (CMC), which provides several

essential systems management features:

– Enclosure-level power management and thermal management:

• The CMC monitors system power requirements and supports the

optional Dynamic Power Supply Engagement mode so that the

CMC can enable or place power supplies in standby dynamically,

depending on load and redundancy requirements, to improve

power efficiency.

• The CMC reports real-time power consumption.

• The CMC supports an optional power ceiling, which will either

trigger an alert or actions to keep the enclosure power

consumption under the predefined ceiling.

• The CMC monitors and controls cooling fans based on actual

ambient and internal temperature measurements.

– The CMC provides comprehensive enclosure inventory and

status/error reporting.

– The CMC allows centralized configuration of the following settings:

• The CMC’s network and security settings

• Power redundancy and power ceiling settings

• I/O switches and iDRAC network settings

• First boot device on the blades

– The CMC will check I/O fabric consistency between the I/O modules

and blades and will disable system components if necessary to protect

the system hardware.

– User access security.

– An SD card slot on the CMC card supports an optional persistent

WWN/MAC feature that allows slot-based WWN/MACs for the

blades, simplifying blade installation and replacement.

Getting Started With Your System 5

The CMC has two Ethernet ports. "Gb1" is used to connect to the external

management network. "Stack" allows CMCs in adjacent enclosures to be

daisy-chained. A 24-port Ethernet switch provides internal 100-Mb

communication with the blades, I/O modules, optional iKVM, and

optional second, redundant CMC, and provides a 10/100/1000-Mb

connection to the external management network.

NOTE: The 24-port Ethernet switch is reserved for internal communication

between the iDRAC on the blades to the CMC, then to the external

management network.

A second, optional CMC can be installed for hot-plug failover redundancy.

• An enclosure control panel that includes an LCD display which provides

current infrastructure and blade information, and error reporting.

• An optional Avocent integrated Keyboard, Video and Mouse (iKVM)

module, which includes the following features:

– The iKVM maintains all blade connections as input is switched from

each blade.

– Local iKVM access can be remotely disabled on a per blade basis via

the iDRAC user interface.

– One VGA connector.

– Two USB ports for keyboard and mouse connections.

NOTE: USB functionality is contingent on the connection of a video interface,

such as a monitor cable.

– An RJ-45 ACI port for tiering with external Dell and Avocent analog

KVM and KVM over IP switches with ARI ports. The ACI connection

takes precedence over the rear panel KVM ports.

– The iKVM can also be accessed from the control panel in the front of

the enclosure. Either front or rear KVM functionality is supported

(simultaneous functionality is not supported).

NOTE: The front iKVM is enabled by default if contention exists between the

front and rear iKVM ports. Front iKVM access can be disabled via the CMC

user interface.

6Getting Started With Your System

Blade Features

Performance Features

PowerEdge M905

• Four AMD™

Opteron™ 8000 Series dual-core or quad-core processors.

• A minimum of 8 GB of 677 MHz DDR2 memory modules, upgradable to

a maximum of 192 GB by installing pairs of 1-GB, 2-GB, 4-GB, or 8-GB

modules in the 24 memory module sockets on the blade system board.

The blade also supports memory sparing if eight or sixteen memory

module sockets are populated with identical memory modules.

• An SD (Secure Digital) card slot for embedded Hyperviser support.

PowerEdge M805

• Two AMD

Opteron

2000 Series dual-core or quad-core processors.

• A minimum of 4 GB of 677 MHz DDR2 memory modules, upgradable to

a maximum of 128 GB by installing pairs of 1-GB, 2-GB, 4-GB, or 8-GB

modules in the 16 memory module sockets on the blade system board.

The blade also supports memory sparing if eight or sixteen memory

module sockets are populated with identical memory modules.

• An SD card slot for embedded Hyperviser support.

PowerEdge M600

• One or two Intel

Xeon

dual-core or quad-core processors

• A minimum of 1 GB of 677-MHz FBD memory modules, upgradable to

a maximum of 64 GB by installing pairs of 512-MB, 1-GB, 2-GB, 4-GB,

or 8-GB modules in the eight memory module sockets on the blade system

board. The blade also supports memory sparing or memory mirroring if all

eight memory module sockets are populated with identical memory

modules.

Getting Started With Your System 7

PowerEdge M605

• One or two AMD

Opteron

2000 Series dual-core or quad-core processors.

• A minimum of 1 GB of 677-MHz or 800-MHz DDR2 memory modules,

upgradable to a maximum of 64 GB by installing pairs of 512-MB, 1-GB,

2-GB, 4-GB, or 8-GB modules in the eight memory module sockets on

the blade system board. The blade also supports memory sparing.

Common Features

• The PowerEdge M805 and M905 blades support one or two 2.5 inch SAS

hard drives.

• The PowerEdge M600 and M605 blades support one or two 2.5-inch SATA

hard drives,

one or two 2.5 inch SAS hard drives.

NOTE: SAS and SATA hard drives cannot be mixed within a blade.

Hot-plug drive operation is supported if an optional RAID controller card

is installed in the blade.

• Three USB 2.0-compliant ports (PowerEdge M805 and M905) or two USB

2.0-compliant ports (PowerEdge M605 and M600) support devices such as

a mouse, keyboard, flash drive, diskette drive, or an optical drive.

NOTE: Only Dell-supplied USB devices are supported.

• An integrated VGA-compatible video subsystem with an ATI RN50 video

controller. This video subsystem contains 32 MB of SDRAM video

memory (nonupgradable). Maximum resolution is 1280 x 1024 x 65,000

colors (noninterlaced).

• An Integrated Dell Remote Access Controller (iDRAC), which provides

remote system management, blade-level power management, virtual KVM

and virtual media support, remote alerting and event logging.

• Four 1-GB Ethernet ports supported by two integrated dual-port

Broadcom 5709S controllers (PowerEdge M805 and M905), or two 1-GB

Ethernet ports supported by two integrated Broadcom 5708S controllers

(PowerEdge M600 and M605). TCP/IP Offload Engine (TOE) and iSCSI

boot are supported.

For a complete list of system features, see "Technical Specifications" on

page 15.

8Getting Started With Your System

The following software is included with your system:

• A System Setup program for quickly viewing and changing system

configuration information. For more information on this program, see

"Using the System Setup Program" in your

Hardware Owner’s Manual

• Enhanced security features, including a system password and a setup

password, available through the System Setup program.

• System diagnostics for evaluating system components and devices.

For information about the system diagnostics, see "Running the System

Diagnostics" in your

Hardware Owner’s Manual

• Video drivers for displaying many popular application programs in high-

resolution modes.

• Systems management software and documentation. Systems management

software is used to manage and monitor each individual blade as well as

the system as a whole, including all of the blades, network switch modules,

power supplies, and fans. Systems management software manages the

system locally and remotely on a network. Dell recommends that you use

the systems management software provided with this system.

• Optional solutions software for Web hosting, caching, or load balancing.

See your solutions software documentation for more information.

Supported Operating Systems

• Microsoft

Windows Server™ 2003, Web, Standard and Enterprise

(32-bit x86) Editions with SP2

• Microsoft Windows Server 2003, Standard, Enterprise, and DataCenter

(x64) Editions SP1, SP2

• Microsoft Windows Server 2003 R2 Standard and Enterprise (32- bit x86)

Editions with SP1, SP2

• Microsoft Windows Server 2003 R2 Standard, Enterprise, and DataCenter

(x64) Editions with SP1, SP2

• Microsoft Windows Server 2008, Standard Edition with SP1, SP2,

DataCenter, and EM64T

•RedHat

Enterprise Linux

AS, ES, and WS (version 4) and EM64T

• Red Hat Enterprise Linux AS and ES (version 4) (ia32

)

Autres manuels pour POWEREDGE M905

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Dell Serveur

Dell

Dell PowerEdge 2410 Manuel utilisateur

Dell

Dell External OEMR R410 Guide de démarrage rapide

Dell

Dell PowerEdge 700 Mode d’emploi

Dell

Dell PowerEdge R630 Manuel utilisateur

Dell

Dell PowerEdge R610 Manuel utilisateur

Dell

Dell EMC DSS 9620 Manuel

Dell

Dell PowerEdge C6220 II Manuel utilisateur

Dell

Dell POWEREDGE SC440 Manuel utilisateur

Dell

Dell PowerEdge 6600 Manuel utilisateur

Dell

Dell PowerEdge C6105 Manuel d'utilisation

Dell

Dell PowerEdge R210 Manuel utilisateur

Dell

Dell PowerEdge C6145 Manuel utilisateur

Dell

Dell PowerEdge R660xs Manuel

Dell

Dell PowerEdge C5220 Manuel utilisateur

Dell

Dell DR6300 Manuel utilisateur

Dell

Dell PowerEdge R200 Manuel utilisateur

Dell

Dell PowerVault NX3100 Manuel utilisateur

Dell

Dell PowerEdge T310 Manuel utilisateur

Dell

Dell VxRail E660 Manuel

Dell

Dell OptiPlex 3000 Manuel d'exploitation et d'entretien

Dell

Dell PowerEdge R530xd Manuel utilisateur

Dell

Dell PowerEdge T630 Manuel utilisateur

Dell

Dell EMC PowerEdge T440 Manuel

Dell

Dell PowerEdge 600SC Manuel utilisateur

Manuels Serveur populaires d'autres marques

HP AlphaServer ES47 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

HP ProLiant Gen9 Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

HP Integrity rx2600 Guide d'installation

Milestone

Milestone Husky IVO 350T Manuel utilisateur

Planet

Planet NAS-7410 Manuel utilisateur

Lenovo

Lenovo ThinkSystem SR635 V3 Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY BX900 Manuel utilisateur

Asus

Asus RS700DA-E6 PS4 Manuel utilisateur