Dell SC4020 Manuel utilisateur

Dell™ SC4020

Storage Controller

Getting Started

With Your System

Regulatory Model Series E10J

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make

better use of your Storage Center.

CAUTION: A CAUTION indicates potential damage to hardware or loss of

data if instructions are not followed.

WARNING: A WARNING indicates a potential for property damage,

personal injury, or death.

Contacting Dell Technical Support Services

For technical support, go to support.dell.com/compellent/.

____________________

Information in this document is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission

of Dell Inc. is strictly forbidden.

international copyright and intellectual property laws. Dell and the Dell logo are trademarks

of Dell Inc. in the United States and/or other jurisdictions. All other marks and names

mentioned herein may be trademarks of their respective companies.

March 2014 P/N 667T7 Rev. A00

Getting Started With Your System 1

Installation and Configuration

WARNING: Before performing the following procedure, review the safety

instructions that came with all Storage Center components.

WARNING: Battery pack MUST be removed before the controller is

removed from the enclosure.

WARNING: Installing an incompatible battery on the server board may

increase the risk of fire or explosion. Observe the following precautions:

•

The battery should only be replaced with a battery that is the same or

equivalent as the factory installed battery.

•

Do not attempt to open or service the battery. Do not dispose of the

battery in a fire or with household waste. Contact the local waste

disposal agency for the location of the nearest battery deposit site.

Laser Safety statement

The unit is certified in the U.S. to conform to the requirements of DHHS

21 CFR, chapter 1 Subchapter J for Class I (1) laser products, and

elsewhere is certified as a Class I laser product conforming to the

requirements of IEC 60825-1:2007.

Class I laser products are not considered to be hazardous. The laser

system and unit are designed so there is never any human access to

laser radiation above a Class I level during normal operation, user

maintenance or prescribed service condition.

Unpacking the System

NOTE: Unpacking, installing, and deploying your Storage Center may be

done only by a certified service technician.

CAUTION: Class I laser radiation when open, avoid

exposure to the beam.

DANGER: Laser radiation, avoid direct exposure to beam.

2 Getting Started With Your System

Before you begin, make sure the site where you intend to set up and use

the Storage Center has the following:

•

Standard power from an independent source or a rack power

distribution unit with a UPS.

•

Storage Center with the latest firmware, BIOS, and drivers. Contact

your supplier for the correct software versions.

Installation Overview

The installation process follows the general steps below. For detailed

information, refer to vendor documentation supplied with the equipment.

NOTE: The system is intended for restricted access location in

accordance with the National Electric Code, National Standards Institute

(ANSI/National Fire Protection Association (NFPA) 70).

CAUTION: If installed in a closed or multi-unit rack assembly, the

operating ambient temperature of the rack environment may be greater

than room ambient temperature. Therefore, consideration should be given

to installing the equipment in an environment compatible with the maximum

ambient temperature (Tma) specified by the manufacturer. For more

information, see "Technical Specifications" on page 7.

Assemble the rails following the safety instructions and the rack

installation instructions provided with your system.

Install network switches, as applicable.

Install the SC4020 chassis into the rack.

•

Always load the rack from the bottom up for weight stability.

Getting Started With Your System 3

•

You can allow room for expansion if you have fewer than the

maximum number of enclosures.

Unwrap and insert each drive into the enclosure one at a time.

•

Protect the drive from static discharge.

•

Handle drives by the edges of the frame.

CAUTION: If the enclosure system operates for more than a few minutes

with missing drives, the enclosure can overheat, causing power failure and

data loss. Such use may invalidate the warranty.

4 Getting Started With Your System

Connecting the Power Cables

Ensure that the power switch is in the OFF position before connecting

the power cables.

Connect the enclosure power cables to the rack power.

Securing the Power Cables

Secure the cables firmly to the bracket using the strap provided.

Plug the other end of the power cables into a grounded electrical

outlet or a separate power source such as an uninterrupted power

supply (UPS) or a power distribution unit (PDU).

Getting Started With Your System 5

Location of Power Button

NOTE: Do not power up the enclosure until all Storage Center

components are racked and cabled.

Installing the Bezel

•

Install the bezel.

6 Getting Started With Your System

Other Information You May Need

WARNING: See the safety and regulatory information that shipped with

your Storage Center components. Warranty information may be included

within this document or as a separate document.

•

The rack documentation included with your rack solution describes

how to install your system into a rack.

•

The Storage Center Deployment Guide provides information about

cabling all Storage Center hardware components and configuring a

new Storage Center using the System Manager Setup Wizard.

•

The Storage Center System Manager Administrator’s Guide describes

how to manage a Storage Center.

Autres manuels pour SC4020

Table des matières

Autres manuels Dell Contrôleurs

Dell

Dell PowerConnect W-650 Manuel utilisateur

Dell

Dell PowerVault 660F Manuel utilisateur

Dell

Dell PowerEdge Expandable RAID Controller 3 Manuel utilisateur

Dell

Dell PowerEdge 2650 Manuel utilisateur

Dell

Dell PowerConnect W-3200 Manuel utilisateur

Dell

Dell EMC PowerEdge VRTX Manuel utilisateur

Dell

Dell H310 Manuel utilisateur

Dell

Dell W-7205 Series Manuel utilisateur

Dell

Dell PowerEdge Manuel utilisateur

Dell

Dell PowerEdge M1000e Manuel utilisateur

Dell

Dell PowerEdge Series Manuel d'utilisation et d'entretien

Dell

Dell PowerEdge FX2 Manuel utilisateur

Dell

Dell PowerEdge 2800 Manuel utilisateur

Dell

Dell iDRAC Comment utiliser

Dell

Dell PowerConnect W-620 Manuel utilisateur

Dell

Dell PowerConnect W-6000 Manuel utilisateur

Dell

Dell Networking W-7024 Manuel utilisateur

Dell

Dell PERC 5/i Manuel utilisateur

Dell

Dell CMC Manuel

Dell

Dell 3-DNS Manuel de service

Dell

Dell USC Manuel utilisateur

Dell

Dell SC8000 Guide de référence rapide

Dell

Dell Dial Totem Manuel utilisateur

Dell

Dell PowerConnect W-650 Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur