Dell LC-EJ-10GE-10P Manuel utilisateur

101-00348-05 | 1

Installing ExaScale Line Cards

Dell Force10 Catalog Numbers: LC-EH-10GE-10P, LC-EJ-10GE-10P, LC-EH-10GE-10S, LC-EJ-10GE-10S,

LC-EH-10GE-40S, LC-EJ-10GE-40S, LC-EH-GE-50P, LC-EJ-GE-50P, LC-EH-GE-90M, LC-EJ-GE-90M

The E-Series ExaScale requires at least one line card to operate. You can add, replace, or remove line

cards without interrupting the system power or system operations. Any line card can be inserted into any

line card slot.

NOTE: ExaScale line cards have a minimum FTOS version requirement. See

Table 1-1

NOTE:All chassis slots must be installed with operational modules or blanks.Always replace cards and blank

panels immediately.

Figure 1-6. Installing a line card

2| 101-00348-05

www.dell.com | support.dell.com

Installing line cards

WARNING: Electrostatic discharge (ESD) damage can occur when components are mishandled. Always

wear an ESD-preventive wrist or foot-heel ground strap when handling line cards. Place line cards on an

antistatic surface when they are not installed.

Removing line cards

WARNING: Do not remove a panel blank unless you are ready to install a line card into that slot. After

removing a line card, immediately place a panel blank in the empty slot. Blanks are required to control airflow

and electromagnetic interference.

Step Task

4Verify that the chassis is running the minimum FTOS version for the line card that you are installing.

5Completely extend the ejector lever (rotate away from the chassis).

6Align the card with the card slot guides, and slide it into the slot until the connectors engage with the chassis

backplane. Avoid touching the printed circuit board or connector pins.

7Rotate the ejector lever towards the chassis to seat the card into place. The card should be flush with the chassis.

8Secure the card in place by tightening the top and bottom captive screws.

Step Task

1Unplug the network interface cables connected to the line card.

2Unscrew the captive screws and rotate the ejector lever away from the chassis to disengage the backplane

connections.

3Use the ejector lever and the card handle to pull the card out of the slot. Avoid touching the printed circuit board

and connector pins.

4Insert a blank panel into all empty slots. Blanks do not have board components or connector pins. Align the blank

with the slot guides and push it until it is flush with the chassis. Tighten the captive screws to secure the panel in

place.

101-00348-05 | 3

Line Card Hardware/Software Requirements

Line Card LED Description

Figure 1-7. ExaScale 4-port 40G line card

NOTE: The 4-port 40G line card protrudes from the chassis front by approximately 2 inches. Do not force the

card flush to the chassis front when installing. The locking levers will secure the card when it is seated in the

backplane.

NOTE:

•The following FTOS features are NOT supported on the 4-port 40G line card (LC-EH-40GE-4P,

LC-EJ-40GE-4P): Ipv6 MultiCast, Non-default CAM profiles, BFD, PBR, Flow, VLAN Stacking; QOS, CFP

Optics. Installing the line card in a system running these features can lead to unpredictable behavior.

Table 1-1. ExaScale Line Card Hardware/Software Requirements

Catalog Number Description Hardware Requirements Minimum FTOS

Version

10 port 10GE line card with XFP optics (10M

CAM) LC-EH-10GE-10P XFP optics are required 8.3.1.0

10 port 10GE line card with XFP optics (40M

CAM) LC-EJ-10GE-10P XFP optics are required 8.3.1.0

10 port 10GE line card (10M CAM) LC-EH-10GE-10S SFP+ optics are required 8.1.1.1

10 port 10GE line card (40M CAM) LC-EJ-10GE-10S SFP+ optics are required 8.1.1.1

40 port 10GE line card with SFP+ optics

(10M CAM) LC-EH-10GE-40S SFP+ optics are required 8.3.1.2

40 port 10GE line card with SFP+ optics

(40M CAM) LC-EJ-10GE-40S SFP+ optics are required 8.3.1.2

50 port 1GE line card (10M CAM) LC-EH-GE-50P — 8.3.1.0

50 port 1GE line card (40M CAM) LC-EJ-GE-50P — 8.3.1.0

90 port 1GE line card (10M CAM) LC-EH-GE-90M requires MRJ21 cables 8.1.1.2

90 port 1GE line card (40M CAM) LC-EJ-GE-90M requires MRJ21 cables 8.1.1.2

Label Description

Port L/A:

Blinking Green: Link detected/ Activity

Solid Green: Link detected/ No Activity

Off: No Link/ Card Offline

Status LED Green: operational

Red: card problem state

Flashing green: booting/ diagnostics

Unlit: in standby mode or power is off

4| 101-00348-05

www.dell.com | support.dell.com

•LAG is NOT supported on the 4-port 40G line card.

•The 4-port 40G line card can be configured for linerate or oversubscribed mode (linecard id [linerate |

oversubscribes] active-ports port-set number CLI in CONFIGURATION mode).

•The line card must be rebooted when mode or port changes are made.

•Line card boot up may take up to 6 minutes.

Figure 1-8. ExaScale 90-port 1G line card

NOTE: 90-port 1G line cards have six port LEDs per input connector (one for every physical port).

Figure 1-9. ExaScale 10-port 10G line card

Figure 1-10. ExaScale 50-port 10G line card

Ce manuel convient aux modèles suivants

Autres manuels Dell Unité de contrôle

Dell

Dell MXG610s Manuel utilisateur

Dell

Dell UPS 2700R Series Manuel utilisateur

Dell

Dell PowerEdge M420 Manuel utilisateur

Dell

Dell PowerConnect W-6000M3 Manuel utilisateur

Dell

Dell PowerEdge FN Manuel utilisateur

Dell

Dell PowerConnect W Series Instructions d'utilisation et d'entretien

Dell

Dell K804N Manuel utilisateur

Dell

Dell FC SAN Manuel utilisateur

Dell

Dell H955N Manuel utilisateur

Dell

Dell PowerEdge M420 Manuel de service

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur