DDDrop EVO TWIN Manuel utilisateur
0
EN 190524
Installation and User manual
Models EVO TWIN
PM4, Firmware 181114 and later
ENGLISH
Translation of Dutch original
1
EN 190524
Contents
1 Introduction ....................................................................................................................................3
2 Product details................................................................................................................................4
2.1 Specifications dddrop EVO......................................................................................................4
2.2 Printer overview......................................................................................................................5
3 Installation of the device ................................................................................................................6
3.1 Placing the device ...................................................................................................................6
3.2 Removing transport materials ................................................................................................7
3.3 Connecting power.................................................................................................................10
4 Use of EVO Twin............................................................................................................................11
4.1 Before printing......................................................................................................................11
4.2 User Interface .......................................................................................................................11
4.2.1 Status tab ......................................................................................................................12
4.2.2 Tuning tab .....................................................................................................................12
4.2.3 File tab...........................................................................................................................13
4.2.4 Tool tab .........................................................................................................................13
4.2.5 Settings tab ...................................................................................................................13
5 First print.......................................................................................................................................14
5.1 Preparation of material.........................................................................................................14
5.2 Preparing heated bed ...........................................................................................................15
5.3 Start Print..............................................................................................................................15
5.4 Taking out the printed model ...............................................................................................15
6 Maintenance.................................................................................................................................16
6.1 Adjusting heated bed............................................................................................................17
6.2 Empty the container .............................................................................................................17
6.3 Cleaning the brush................................................................................................................17
7 Safety and Conformity ..................................................................................................................18
7.1 Electromagnetic compatibility (EMC) ...................................................................................18
7.2 Electrical safety.....................................................................................................................18
7.3 Mechanical safety .................................................................................................................18
7.4 Risk of burn ...........................................................................................................................18
7.5 Health....................................................................................................................................18
7.6 General note on safety .........................................................................................................19
2
EN 190524
3
EN 190524
1Introduction
This manual covers the necessary steps to get the best results from your dddrop 3D printer. It is
possible that you already have experience with other versions of dddrop 3D printers. It is however
recommended to study this manual thoroughly in order to understand the latest procedures related
with the use of the dddrop EVO 3D printers.
In chapter 2 the product specifications are given of the dddrop EVO Twin together with an overview
of the machine. In chapter 3 the installation of the printer is described followed by its use in chapter
4. Chapter 5 covers the procedure on how a print is started. Additionally, Maintenance and Safety
are found in chapters 6 and 7 respectively.
Figure 1. Quick start Steps
Following the quick start steps above, the manual guides you step by step through the procedures.
Information that requires extra attention is presented in the following format:
WARNING
A warning is given when the concerning procedure may cause harm or injury to the user, or
damage to the machine. A warning precedes the section it relates to.
Installation
•Positioning
•Connecting the power supply
Use
•Before printing
•User Interface
First print
•Print order preparation
•Start a prepared print
4
EN 190524
2Product details
2.1 Specifications dddrop EVO
Printing
Print method
Fused Filament Fabrication (FFF)
Print volume
330 x 310 x 305 mm
Layer thickness
0,05-0,75 mm*
Filament diameter
1,75 mm
Nozzle diameter
0,2 –0,4 (standard) –0,6 –0,8 –1,0 mm**
Print speed
Max. 150 mm/s
Printer dimensions
Printer dimensions
X 530 mm
Y 660 mm
Z 570 mm
Mass
± 30 kg
Total transport mass
± 36 kg
Temperature
Environment temperature at use
15 –30°C, 10-90% relative humidity without condensation
Nozzle temperature range
150 –300°C
Heated bed temperature range
Up to 130°C
Power and Connectivity
Power
AC input 100-240VAC | 10A - 5A | 47-63Hz
Connectivity
USB
2.4GHz WiFi
LAN
Sound
Average sound level (in use)
<55dB(A)
(*) Standard settings with standard nozzle included (0.20mm layer thickness, 0.4mm nozzle), possibly smaller nozzles are
required for reduced layer thicknesses, please contact your supplier.
(**) Other nozzle diameters (e.g. 0.2mm, 0.4mm, 0.6mm, 0.8mm and 1.0mm) are optional, please contact your supplier.
5
EN 190524
2.2 Printer overview
Figure 2. Printer overview (dddrop EVO Twin)
Cover stand
Printer head
Heated bed
Adjustable Heated bed levelling
USB connection
Touchscreen
Filament Management Module
Filament reel extruder 1
Filament reel extruder 2
ON/OFF Switch
Power connection
Internet connection
6
EN 190524
3Installation of the device
In this chapter the installation of the dddrop EVO Twin printers is described. These steps have to be
made before use. The first step is placing the machine on a stable support, removing the transport
materials followed by the power connection to the mains. After completing these steps, the printer
can be used.
WARNING
The machine needs to be lifted and moved by two persons using the grips on both sides of the
machine in order to minimize the chance of pinching or dropping of the device. Place the machine
on a stable support with a loading capacity of at least 50kg.
WARNING
The machine is to be used in well ventilated areas only. Fumes that can occur during the printing
process are material dependent and, especially in case of insufficient ventilation, have to be
extracted.
3.1 Placing the device
The dddrop printer is supplied with an USB stick, two filament holders, container, internet cable and
a power cord. Accessories like Quick Starting kits can be ordered additionally enabling the user to
start right away.
The machine needs to be placed on a stable support with a loading capacity of at least 50kg in a well
ventilated area, free of weather influences, limited humidity and at room temperature.
WARNING
The machine is shipped with transport materials which have to be removed before the machine is
connected to the power and put to use. Failure to remove the transport materials may cause
damage to machine components beyond repair.
7
EN 190524
3.2 Removing transport materials
In this chapter, unpacking the printer will be shown step by step.
Step 1: Remove the protection film from the cover on both sides.
Step 2: Remove the protection film from the touchscreen by pulling on the green tab.
Step 3: Remove the tie wraps that hold the transport protection on two axes.
Step 4: Remove the tie wraps and the corner protection that holds your spare glass plate in place.
8
EN 190524
Step 5: Remove the transport protection from the x and after that from the y axis.
Step 6: Remove the small pieces of transport protection from both axes.
Step 7: Grab the spare glass plate by pulling it towards to you.
Step 8: Grab the printer accessories from the right side of the printer.
(Power cable, Container, Lan Cable, USB Stick, Password card, two filament holders.)
9
EN 190524
Step 9: Place the container in front of the printer (see red arrow on the left picture below) and place
the filament holders on the back of the printer.
WARNING
Only use the power cable provided when connecting the machine to the mains. Use a grounded
wall plug. Ensure that during maintenance the machine is turned OFF (O) and the mains cable is
detached.
WARNING
Before connecting your machine, ensure that the power switch is switched OFF (O) before
connecting the power cable to the mains. The machine can be turned off AT ANY TIME by
switching the power switch from ON (I) to OFF (O). It is however strongly recommenced to only
switch the machine OFF when it is not in use.
Table des matières
Autres manuels DDDrop Imprimante 3D
