Daikin BRC7EA629 Manuel utilisateur

Installation manual

BRC7EA628

BRC7EA629

BRC7EA630

BRC7EA631

BRC7EA632

Wireless Remote Controller Kit

3PEN505117-3C.book Page 1 Monday, July 19, 2021 11:29 AM

1English

BRC7EA628

BRC7EA629

BRC7EA630

BRC7EA631

BRC7EA632

Wireless Remote Controller Kit Installation manual

CONTENTS

SAFETY PRECAUTIONS............................................................... 1

BEFORE INSTALLATION .............................................................. 2

REMOTE CONTROLLER INSTALLATION .................................... 2

RECEIVER INSTALLATION........................................................... 3

FIELD SETTING ........................................................................... 10

TEST OPERATION ...................................................................... 12

Read these instructions carefully before installation. Keep this manual in a handy place for future reference.

The English text is the original instruction. Other languages are translations of the original instructions.

1. SAFETY PRECAUTIONS

Please read these “SAFETY PRECAUTIONS” carefully before installing air conditioning equipment and be

sure to install it correctly. After completing the installation, make sure at start up operation that the unit oper-

ates properly. Please instruct the customer how to operate the unit and keep maintenance.

Meaning of caution symbols

CAUTION .............. If the caution is not observed, it may cause injury or damage to equipment.

NOTE ............. These instructions will ensure proper use of the equipment.

CAUTION

•Refer also to the installation manual attached to the indoor unit.

•Confirm that following conditions are satisfied prior to installation.

•Ensure that nothing interrupts the operation of the wireless remote controller. (Ensure that there is nei-

ther a source of light nor fluorescent lamp near the receiver. Also, ensure that the receiver is not

exposed to direct sun light.)

•Ensure that the operation display lamp and other indicators are easy to see.

3PEN505117-3C.book Page 1 Monday, July 19, 2021 11:29 AM

English 2

2. BEFORE INSTALLATION

2-1 ACCESSORIES

Check if the following accessories are included with your option kit.

2-2 NOTE TO THE INSTALLER

•Be sure to instruct the customer how to properly operate the system showing him/her the attached opera-

tion manual.

3. REMOTE CONTROLLER INSTALLATION

Installing wireless remote controller

•Do not throw the remote controller or impose large shocks. Also, do not store where it may be exposed to

moisture or direct sunlight.

•When operating, point the transmitting part of the remote controller in the direction of the receiver.

•

The direct transmitting distance of the remote controller is approximately 7 meters.

•

The signal cannot be transmitted if something (e.g. curtains) blocks the receiver and the remote controller.

Name

Receiver

(3) Relay

harness - long

(4) Relay

harness - short

Wireless

remote

controller

Screw

(1) Light receiver

assembly

(2) Transmission

PC-board

Quantity

1 pc. 1 pc. 1 pc. 1 pc. 1 pc. 2 pcs.

Shape

Name Remote controller

holder

(5) Unit No.

nameplate (6) Control panel (with label) (7) Clamp

Quantity

1 pc. 1 pc. 1 pc. 1 pc.

Shape

Name Sealing material (8) Dry cell battery

LR03 (AM4) Operation manual Installation manual

Quantity

1pc. 2 pcs. 1 pc. 1 pc.

Shape



BRC7EA628~631

BRC7EA632

BRC7EA628~631

BRC7EA632

3PEN505117-3C.book Page 2 Monday, July 19, 2021 11:29 AM

3English

• Installing to a wall or a pillar

Fix the remote controller holder with the screws.

Slide the remote controller into the remote controller holder

from the top.

• How to insert the batteries

Open the back cover of the remote controller by sliding it in the

direction of the arrow.

Insert the attached dry cell batteries. Properly insert, set the bat-

teries by matching the (+) and (–) polarity marks as indicated.

Then close the back cover as before.

4. RECEIVER INSTALLATION

(1) Preparations before installation

Remove the service cover and the front grill. See the installation manual that came with the main indoor

unit for details on removal.

(2) Determination of address and MAIN/SUB remote controller.

If setting multiple wireless remote controllers to operate in one room, perform address setting for the

receiver and the wireless remote controller.

If setting multiple wired remote controllers in one room, change the MAIN/SUB switch of the receiver.

SETTING PROCEDURE

1. Setting the receiver

Set the wireless address switch (SS2) on the transmission PC-board (2) according to the table below.

When using both a wired and a wireless remote

controller for 1 indoor unit, the wired controller

should be set to MAIN. Therefore, set the MAIN/

SUB switch (SS1) of the receiver to SUB.

(The wired remote controller will be “MAIN”.)

Unit No. No. 1 No. 2 No. 3

Wireless address

switch (SS2)

MAIN SUB

MAIN/SUB

switch (SS1)



 

The side painted black indicates

the switch knob position.









 

 !

3PEN505117-3C.book Page 3 Monday, July 19, 2021 11:29 AM

English 4

2. Setting the address of wireless remote controller (It is factory set to “1”)



Setting from the remote controller



Hold down the

button and the

button

for at least 4 seconds to get the Field Set mode.

(Indicated in the display area in the figure at right.)

Press the

button and select a multiple

setting (A/b). Each time the button is pressed the dis-

play switches between “A” and “b”.

Press the “

”

button and “

”

button to set the

address.

Address can be set from 1 to 6, but set it to 1 ~ 3 and

to same address as the receiver. (The receiver does

not work with address 4 ~ 6.)

Press the button to enter the setting.

Hold down the button for at least 1 second to

quit the Field Set mode and return to the normal

display.

Multiple settings A/b

When the indoor unit is being operated by outside control (central remote controller, etc.), it sometimes does

not respond to ON/OFF and temperature setting commands from this remote controller. Check what setting

the customer wants and make the multiple setting as shown below.

Attach the included unit number nameplate (5)

to the front grill on the indoor unit and the back

of the wireless remote controller

[PRECAUTIONS]

Set the unit number of the receiver and the wire-

less remote controller to be equal. If the setting

differs, the signal from the remote controller

cannot be transmitted.

Remote controller Movement when the operation is controlled by the

other air conditioners and equipment

Multiple setting Remote controller display

A: Standard All items displayed.

When operation changeover, temperature setting or

the like is carried out from the remote controller, the

indoor unit rejects the instruction.

(Signal receiving sound “peeh” or “pick-pick-pick”)

As a result, a discrepancy between the operation

state of the indoor unit and the indication of the

remote controller display occurs.

b: Multi System

Operations remain dis-

played shortly after exe-

cution.

All commands accepted.

(Signal receiving sound “pick-pick”)

Since the indication of the remote controller is turned

off, no discrepancy such as mentioned above occurs.























 









 

/TEST

FAN

DOWN

 !"#$

4-5-48-

/TEST

Front grille

Unit No. nameplate (5)

Wireless remote

controller

3PEN505117-3C.book Page 4 Monday, July 19, 2021 11:29 AM

5English

(3) Attaching the receiver

Connect the included relay harness – long (3) and relay harness – short (4) to the connector

on the transmission PC-board (2).

Following the figure, insert transmission PC-board (2) into tab

, then insert into tab

while pushing

tab

in the direction of the arrow.

Attach the included light receiver assembly (1) to the 2 tabs on the indoor unit, according to following figure.





     

 

   !

  " #

Tab



Tab



Transmission

PC-board (2)

Transmission

PC-board (2)

When attaching transmission

PC-board (2), be sure not to

bend the PC-board.

When attaching transmission

PC-board (2), be careful not

to change any of the settings

of the set switches.

Tab

Tab Light receiver assembly (1)

3PEN505117-3C.book Page 5 Monday, July 19, 2021 11:29 AM

English 6

Connect the relay harnesses which were connected to the transmission PC-board (2) in step

as follows.

•

Relay harness – long (3) to connector X24A on the indoor

unit PC-board

•

Relay harness – short (4) to connector CN1/X1A on the light receiver assembly (1)

After making these connection, clamp down relay harness – long (3) and relay harness – short (4) using

the included clamp (7).

Connect firmly to

the connector.

Connect firmly to

the connector.

Connector (X24A) (Black)

Indoor unit PC-board

Relay harness – long (3)

Clamp (7)

Cut off any excess

material after tightening.

Relay harness

– short (4)

Connector (CN1/X1A)

Light receiver assembly (1)

BRC7EA628/29

BRC7EA630/631 - in combination with a VRV indoor unit

Use clamp (7) to fix the wires if necessary.

Cut off any excess material after tightening.

Connect firmly to the connector X24A (black)

Relay harness - long (3)

Connect firmly to

the connector.

Relay harness - short (4)

Connector (CN1/X1A)

Light receiver assembly (1)

3PEN505117-3C.book Page 6 Monday, July 19, 2021 11:29 AM

7English

BRC7EA631 - in combination with a Sky Air indoor unit

Relay harness - long (3)

Connect firmly to

the connector.

Relay harness - short (4)

Connector (CN1/X1A)

Light receiver assembly (1)

Connect firmly to the connector X24A (black)

Use clamp (7) to fix the wires if necessary.

Cut off any excess material after tightening.

BRC7EA632

Relay harness - long (3)

Connect firmly to

the connector.

Relay harness - short (4)

Connector (CN1/X1A)

Light receiver assembly (1)

Connect firmly to the connector X24A (black)

Use clamp (7) to fix the wires if necessary.

Cut off any excess material after tightening.

3PEN505117-3C.book Page 7 Monday, July 19, 2021 11:29 AM

English 8

(4) Attaching the control panel

BRC7EA628, 629, 630, 631

Remove the sealing material and prepare new replacement sealing material (accessory).

Inside view of the front grill

NOTE

•

The hook positions are the same for both pre-installed cover and control panel.

Slide the cover to side while pushing the cover on A position from the back side and on B position from

the front side. Hooks 1 and 2 will be removed from their positions.

Take the cover away by pulling the left side of the cover away from the front grill, removing hooks 3a,

3b and 4 from their position.

Position the hook 4 on the control panel to the correct location on the front grill.

Attach the hooks 3a and 3b by pushing them against the front grill.

Slide the control panel as indicated to attach hooks 1 and 2 to their correct position.

Sealing

material

Cover

(pre-installed)

Hoo

k 2

Hook 3a

Hook 3b

Hook 4 Hook 1

2a 2b 3

4 65

3PEN505117-3C.book Page 8 Monday, July 19, 2021 11:29 AM

9English

The control panel should be placed in the front grill as in the following figure.

Attach new sealing material in the original position (accessory (8)).

Attach the front grill and service cover to the indoor unit according to installation manual of the indoor

unit.

BRC7EA632

Remove the sealing material and prepare new replacement sealing material (accessory).

Inside view of the front grill

NOTE

•

The hook positions are the same for both pre-installed cover and control panel.

To remove the pre-installed cover, pull away the part of the front grille slightly (as indicated below) to detach

it from the hook (1) and slide the cover to the outer side to remove cover from the hooks (2).

Hook 1

Hook 2

Cover (pre-installed)

Sealing

material

3PEN505117-3C.book Page 9 Monday, July 19, 2021 11:29 AM

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Daikin Télécommande

Daikin

Daikin BRC1E71 Manuel utilisateur

Daikin

Daikin BRC1E73 Manuel utilisateur

Daikin

Daikin BRC1H82W Manuel utilisateur

Daikin

Daikin BRC7GA53 Manuel utilisateur

Daikin

Daikin BRC1H62W Manuel utilisateur

Daikin

Daikin BRC7EA628 Manuel utilisateur

Daikin

Daikin BRC7C62 Manuel utilisateur

Daikin

Daikin BRC1H519W Manuel utilisateur

Daikin

Daikin SRC-COA Manuel utilisateur

Daikin

Daikin BRC1D71 Manuel utilisateur

Daikin

Daikin BRC51D61 Manuel utilisateur

Daikin

Daikin BRC1E72 Manuel utilisateur

Daikin

Daikin BRC7EA530W Manuel utilisateur

Daikin

Daikin BRC7CB58 Manuel utilisateur

Daikin

Daikin BRC1E51 Manuel utilisateur

Daikin

Daikin BRC2E52C7 Manuel utilisateur

Daikin

Daikin BRC1D517 Manuel utilisateur

Daikin

Daikin BRC301B61 Manuel utilisateur

Daikin

Daikin ARC433A51 Manuel d'instructions

Daikin

Daikin BRC1H81W Guide de l'utilisateur

Daikin

Daikin Madoka Manuel utilisateur

Daikin

Daikin BRC1E53 Comment utiliser

Daikin

Daikin BRC082A43 Manuel utilisateur

Daikin

Daikin BRC230Z8A Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation