D-Link XStack DES-3526 Manuel utilisateur

CLI Manual

Product Model : xStackTM DES-3526/DES-3526DC

Layer 2 Managed Stackable Fast Ethernet Switch

Release 3.60

Table of Contents

INTRODUCTION .........................................................................................................................1

USING THE CONSOLE CLI ........................................................................................................4

COMMAND SYNTAX ..................................................................................................................8

BASIC SWITCH COMMANDS .................................................................................................. 10

SWITCH PORT COMMANDS ...................................................................................................20

PORT SECURITY COMMANDS ...............................................................................................23

NETWORK MANAGEMENT (SNMP) COMMANDS ................................................................. 26

SWITCH UTILITY COMMANDS................................................................................................45

NETWORK MONITORING COMMANDS..................................................................................53

MULTIPLE SPANNING TREE PROTOCOL (MSTP) COMMANDS..........................................66

FORWARDING DATABASE COMMANDS...............................................................................78

BROADCAST STORM CONTROL COMMANDS .....................................................................85

QOS COMMANDS ....................................................................................................................87

PORT MIRRORING COMMANDS............................................................................................. 94

VLAN COMMANDS...................................................................................................................97

ASYMMETRIC VLAN COMMANDS........................................................................................ 102

LINK AGGREGATION COMMANDS ...................................................................................... 104

IP-MAC BINDING .................................................................................................................... 109

LIMITED IP MULTICAST ADDRESS ...................................................................................... 113

BASIC IP COMMANDS ........................................................................................................... 115

IGMP SNOOPING COMMANDS ............................................................................................. 118

DHCP RELAY.......................................................................................................................... 128

802.1X COMMANDS ............................................................................................................... 134

ACCESS CONTROL LIST (ACL) COMMANDS .....................................................................145

TRAFFIC SEGMENTATION COMMANDS .............................................................................154

TIME AND SNTP COMMANDS............................................................................................... 156

ARP COMMANDS...................................................................................................................162

ROUTING TABLE COMMANDS ............................................................................................. 166

MAC NOTIFICATION COMMANDS........................................................................................ 168

ACCESS AUTHENTICATION CONTROL COMMANDS ........................................................ 172

SSH COMMANDS ...................................................................................................................193

SSL COMMANDS ...................................................................................................................200

D-LINK SINGLE IP MANAGEMENT COMMANDS................................................................. 206

COMMAND HISTORY LIST .................................................................................................... 215

TECHNICAL SPECIFICATIONS ............................................................................................. 218

DES-3526 / DES-3526DC Layer 2 Fast Ethernet Switch CLI Reference Manual

Introduction

The Switch can be managed through the Switch’s serial port, Telnet, or the Web-based management agent. The Command Line

Interface (CLI) can be used to configure and manage the Switch via the serial port or Telnet interfaces.

This manual provides a reference for all of the commands contained in the CLI. Configuration and management of the Switch via

the Web-based management agent is discussed in the Manual.

DES-3526/DES-3526DC Managed Layer 2 Fast Ethernet switches are members of the D-Link xStack family. Ranging from

10/100Mbps edge switches to core gigabit switches, the xStack switch family has been future-proof designed to provide a stacking

architecture with fault tolerance, flexibility, port density, robust security and maximum throughput with a user-friendly

management interface for the networking professional.

Please take note that if this device was purchased outside of Europe, certain cosmetic differences between the actual switch and

images in this document will be apparent to the reader, such as the faceplate and the manual cover. The DES-3526/DES-3526DC

has already joined the xStack family for the European market and is soon to be xStack converted, universally. Changes are made

to the appearance of the device only and no configuration or internal hardware alterations occur.

Accessing the Switch via the Serial Port

The Switch’s serial port’s default settings are as follows:

• 9600 baud

• no parity

• 8 data bits

• 1 stop bit

A computer running a terminal emulation program capable of emulating a VT-100 terminal and a serial port configured as above

is then connected to the Switch’s serial port via an RS-232 DB-9 cable.

With the serial port properly connected to a management computer, the following screen should be visible. If this screen does not

appear, try pressing Ctrl+r to refresh the console screen.

Figure 1-1. Initial CLI screen

There is no initial username or password. Just press the Enter key twice to display the CLI input cursor −DES-3526:4#.This is

the command line where all commands are input.

DES-3526 / DES-3526DC Layer 2 Fast Ethernet Switch CLI Reference Manual

Setting the Switch’s IP Address

Each Switch must be assigned its own IP Address, which is used for communication with an SNMP network manager or other

TCP/IP application (for example BOOTP, TFTP). The Switch’s default IP address is 10.90.90.90. You can change the default

Switch IP address to meet the specification of your networking address scheme.

The Switch is also assigned a unique MAC address by the factory. This MAC address cannot be changed, and can be found on the

initial boot console screen – shown below.

Figure 1-2. Boot Screen

The Switch’s MAC address can also be found in the Web management program on the Switch Information (Basic Settings)

window on the Configuration menu.

The IP address for the Switch must be set before it can be managed with the Web-based manager. The Switch IP address can be

automatically set using BOOTP or DHCP protocols, in which case the actual address assigned to the Switch must be known.

The IP address may be set using the Command Line Interface (CLI) over the console serial port as follows:

1. Starting at the command line prompt, enter the commands config ipif System ipaddress

xxx.xxx.xxx.xxx/yyy.yyy.yyy.yyy. Where the x’s represent the IP address to be assigned to the IP interface named

System and the y’s represent the corresponding subnet mask.

2. Alternatively, you can enter config ipif System ipaddress xxx.xxx.xxx.xxx/z. Where the x’s represent the IP address to

be assigned to the IP interface named System and the zrepresents the corresponding number of subnets in CIDR

notation.

The IP interface named System on the Switch can be assigned an IP address and subnet mask which can then be used to connect a

management station to the Switch’s Telnet or Web-based management agent.

DES-3526 / DES-3526DC Layer 2 Fast Ethernet Switch CLI Reference Manual

Figure 1-3. Assigning an IP Address

In the above example, the Switch was assigned an IP address of 10.41.44.254 with a subnet mask of 255.0.0.0. The system

message Success indicates that the command was executed successfully. The Switch can now be configured and managed via

Telnet, SNMP MIB browser and the CLI or via the Web-based management agent using the above IP address to connect to the

Switch.

DES-3526 / DES-3526DC Layer 2 Fast Ethernet Switch CLI Reference Manual

Using the Console CLI

The DES-3526 supports a console management interface that allows the user to connect to the Switch’s management agent via a

serial port and a terminal or a computer running a terminal emulation program. The console can also be used over the network

using the TCP/IP Telnet protocol. The console program can be used to configure the Switch to use an SNMP-based network

management software over the network.

This chapter describes how to use the console interface to access the Switch, change its settings, and monitor its operation.

Note: Switch configuration settings are saved to non-volatile RAM using the save command. The current

configuration will then be retained in the Switch’s NV-RAM, and reloaded when the Switch is rebooted. If

the Switch is rebooted without using the save command, the last configuration saved to NV-RAM will be

loaded.

Connecting to the Switch

The console interface is used by connecting the Switch to a VT100-compatible terminal or a computer running an ordinary

terminal emulator program (e.g., the HyperTerminal program included with the Windows operating system) using an RS-232C

serial cable. Your terminal parameters will need to be set to:

• VT-100 compatible

• 9600 baud

• 8 data bits

• No parity

• One stop bit

• No flow control

You can also access the same functions over a Telnet interface. Once you have set an IP address for your Switch, you can use a

Telnet program (in VT-100 compatible terminal mode) to access and control the Switch. All of the screens are identical, whether

accessed from the console port or from a Telnet interface.

After the Switch reboots and you have logged in, the console looks like this:

DES-3526 / DES-3526DC Layer 2 Fast Ethernet Switch CLI Reference Manual

Figure 2-1. Initial Console Screen after logging in

Commands are entered at the command prompt, DES-3526:4#.

There are a number of helpful features included in the CLI. Entering the ?command will display a list of all of the top-level

commands.

Figure 2-2. The ? Command

When you enter a command without its required parameters, the CLI will prompt you with a Next possible completions:

message.

DES-3526 / DES-3526DC Layer 2 Fast Ethernet Switch CLI Reference Manual

Figure 2-3. Example Command Parameter Help

In this case, the command config account was entered with the parameter <username>. The CLI will then prompt you to enter

the <username> with the message, Next possible completions:. Every command in the CLI has this feature, and complex

commands have several layers of parameter prompting.

In addition, after typing any given command plus one space, you can see all of the next possible sub-commands, in sequential

order, by repeatedly pressing the Tab key.

To re-enter the previous command at the command prompt, press the up arrow cursor key. The previous command will appear at

the command prompt.

Figure 2-4. Using the Up Arrow to Re-enter a Command

In the above example, the command config account was entered without the required parameter <username>, the CLI returned

the Next possible completions: <username> prompt. The up arrow cursor control key was pressed to re-enter the previous

command (config account) at the command prompt. Now the appropriate username can be entered and the config account

command re-executed.

All commands in the CLI function in this way. In addition, the syntax of the help prompts are the same as presented in this manual

−angle brackets < > indicate a numerical value or character string, braces { } indicate optional parameters or a choice of

parameters, and brackets [ ] indicate required parameters.

If a command is entered that is unrecognized by the CLI, the top-level commands will be displayed under the Available

commands: prompt.

DES-3526 / DES-3526DC Layer 2 Fast Ethernet Switch CLI Reference Manual

Figure 2-5. The Next Available Commands Prompt

The top-level commands consist of commands such as show or config. Most of these commands require one or more parameters

to narrow the top-level command. This is equivalent to show what? or config what? Where the what? is the next parameter.

For example, if you enter the show command with no additional parameters, the CLI will then display all of the possible next

parameters.

Figure 2-6. Next possible completions: Show Command

In the above example, all of the possible next parameters for the show command are displayed. At the next command prompt, the

up arrow was used to re-enter the show command, followed by the account parameter. The CLI then displays the user accounts

configured on the Switch.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels D-Link Changer

D-Link

D-Link DUB-H4 Manuel utilisateur

D-Link

D-Link DKVM-8 Manuel utilisateur

D-Link

D-Link EasySmart DES-1100-16 Mode d’emploi

D-Link

D-Link DKVM-2 Manuel utilisateur

D-Link

D-Link GO-SW-5GE Manuel utilisateur

D-Link

D-Link DGS-F1018P-E Manuel utilisateur

D-Link

D-Link GO-SW-5E Manuel utilisateur

D-Link

D-Link DGS-1250-28X Manuel utilisateur

D-Link

D-Link Dis-200G Series Manuel utilisateur

D-Link

D-Link DKVM-2K Manuel utilisateur

D-Link

D-Link GO-SW-8GE Manuel utilisateur

D-Link

D-Link des-1010g Manuel utilisateur

D-Link

D-Link DGS-3000 series Manuel

D-Link

D-Link DGS-3120-24PC-SI Manuel

D-Link

D-Link DUB-H7 - Hub - USB Manuel utilisateur

D-Link

D-Link EasySmart DGS-1100-05 Manuel utilisateur

D-Link

D-Link xStack DGS-3420 Series Manuel utilisateur

D-Link

D-Link xStack DGS-3427 Manuel utilisateur

D-Link

D-Link DSS-16+ Manuel utilisateur

D-Link

D-Link DIS-100G-8W Manuel utilisateur

D-Link

D-Link DIS-100G-5W Manuel utilisateur

D-Link

D-Link DES-1005P Manuel utilisateur

D-Link

D-Link mydlink Smart Plug Lite Manuel utilisateur

D-Link

D-Link DWS-1008 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Manuel utilisateur

D-Link xStack DES-3526 Manuel utilisateur

Manuels Changer populaires d'autres marques