D-Link DCS-7413 Manuel utilisateur
This document will guide you through
the basic installation process for your new
D-Link Network Camera.
DCS-7413
Quick Installation Guide
Full HD Day & Night Outdoor Network Camera
Quick Installation Guide
D-Link DCS-7413 Quick Install Guide
2
Quick Install Guide
This installation guide provides basic instructions for installing the Network Camera on your
network. For additional information about how to use the camera, please see the User’s Manual
which is available on the CD included in this package or from the D-Link support website.
Installation Steps
1. Verify the package contents against the list below.
2. Hardware Overview
3. SD Card Installation
4. Hardware Installation
5. Conguration with Wizard
1. Package Contents
DCS-7413 Network Camera
Quick Install Guide
Power Adapter
AV & Power Cables
CAT5 Ethernet Cable
Extension Adapter
Mounting Bracket and Screws
Manual and Software on CD-ROM
If any of the above items are missing, please contact your reseller.
Safety Notice:
Installation and servicing should be done by certied technicians so as to conform to all local
codes and prevent voiding your warranty.
D-Link DCS-7413 Quick Install Guide
3
2. Hardware Overview
Power Connector
Connects to 12V DC power
24 V Power Connector
Connects to 24 V AC power
Reset Button
Resets camera to factory
default settings
BNC
Analog video output
Ethernet Jack
RJ-45 connector for Ethernet which
can also be used to power the camera
using Power over Ethernet (PoE)
Audio In
Connects to a microphone
DI/DO Wiring, 12V DC output
I/O connectors for external devices
Install the SD Card
Insert the SD card into the
camera with the gold contacts
oriented towards the base of
the camera. To eject the SD
card, push the SD card into
the slot.
3. SD Card Installation
Disassemble the Camera
Open the camera by loosen
the 2 screws.
Audio Out
Connects to speakers
3
1
4
2
D-Link DCS-7413 Quick Install Guide
4
4. Mounting Instructions
Mounting Installation
Please refer to the User Manual for detailed instructions regarding installation and mounting of
the camera using a mounting bracket.
Figure 2.1
Figure 2.3
Figure 2.2
Figure 2.4
D-Link DCS-7413 Quick Install Guide 5
Connection with a PoE switch
If you are using a PoE switch, connect the IP camera to the switch via an Ethernet cable, which
will provide transmission of both power and data over a single cable.
General Connection Using 24V AC Power Wiring
1. Connect the network camera to your network via an Ethernet cable.
2. Connect the supplied power cable from the camera to a power source such as your
building's emergency power.
General Connection Using 12V DC Power Adapter
1. Connect the network camera to your network via an Ethernet cable.
2. Connect the supplied power cable from the camera to a power outlet.
D-Link DCS-7413 Quick Install Guide
6
5. Conguration with Wizard
Click Setup Wizard to begin the installation.
Insert the DCS-7413 CD into your computer's CD-ROM drive to begin the installation. If the Autorun
function on your computer is disabled, or if the D-Link Launcher fails to start automatically, click
Start > Run. Type D:\autorun.exe, where D: represents the drive letter of your CD-ROM drive.
After clicking Setup Wizard, the following window will open.
Click Next to continue.
Click Yes to accept the License Agreement.
Click Finish to complete the installation.
To start the installation process, click Next.
Note: The installation may take several minutes to nish.
D-Link DCS-7413 Quick Install Guide 7
Click on the D-Link Setup Wizard SE icon that was created
in your Windows Start menu.
Start > D-Link > Setup Wizard SE
Take a moment to conrm your settings and click Restart.
Select DHCP if your camera obtains an IP address
automatically when it boots up. Select static IP if the
camera will use the same IP address each time it is started.
Click Next to proceed to the next page.
Enter the Admin ID and password. When logging in for the
rst time, the default Admin ID is admin with the password
left blank.
Click Next to proceed to the next page.
The Setup Wizard will appear and display the MAC address
and IP address of your camera(s). If you have a DHCP server
on your network, a valid IP Address will be displayed. If your
network does not use a DHCP server, the network camera's
default static IP 192.168.0.20 will be displayed.
Click the Wizard button to continue.
D-Link DCS-7413 Quick Install Guide
8
Click on the D-Link Setup Wizard SE icon that was created
in your Windows Start menu.
Start > D-Link > Setup Wizard SE
Viewing Camera via Web Browser
This section shows your camera’s live video. You can select
your video prole and view or operate the camera. For
additional information about web conguration, please
refer to the user manual included on the CD-ROM or the
D-Link website.
Select admin as the User Name and enter your password
(by default the password is blank). Click OK to continue.
Select the camera and click the button labeled "Link" to
access the web conguration.
The Setup Wizard will automatically open your web browser
to the IP address of the camera.
D-Link DCS-7413 Quick Install Guide 9
Notes
D-Link DCS-7413 Quick Install Guide
10
Notes
Autres manuels pour DCS-7413
6
Table des matières
Autres manuels D-Link Caméra de sécurité
D-Link
D-Link DCS-4802E Manuel utilisateur
D-Link
D-Link DCS-3420 Manuel utilisateur
D-Link
D-Link DCS-3715 Manuel utilisateur
D-Link
D-Link DCS-6815 Manuel utilisateur
D-Link
D-Link DCS-936L Manuel
D-Link
D-Link DCS-6100LH/E Manuel utilisateur
D-Link
D-Link DCS-3716 Manuel utilisateur
D-Link
D-Link DCS-2310L Manuel utilisateur
D-Link
D-Link SECURICAM DCS-910 Manuel utilisateur
D-Link
D-Link DCS-6113 Manuel utilisateur
D-Link
D-Link DCS-6915 Manuel utilisateur
D-Link
D-Link DCS-8330LH Manuel utilisateur
D-Link
D-Link DCS-8300LH Manuel utilisateur
D-Link
D-Link DCS-932L Manuel utilisateur
D-Link
D-Link DCS-933L Cloud Camera 1150 Manuel
D-Link
D-Link DCS-6111 Manuel utilisateur
D-Link
D-Link DCS-4605EV Manuel utilisateur
D-Link
D-Link DCS-4602EV Manuel utilisateur
D-Link
D-Link DCS-4603 Manuel utilisateur
D-Link
D-Link DCS-2530L Manuel
