D-Link DSL-6300V Manuel utilisateur

DSL-6300V

USER MANUAL

FEBRUARY 2011

ISSUE 1

All other trademarks are the property of their respective owners..

The information presented is subject to change without notice. D-Link Corporation assumes no responsibility for inaccuracies contained herein.

Conformance statements

The device complies with Part 68 of the Federal Communications Commission (FCC) statements and UL.

iii

Issue 1 February 2011

............................................................................................................................................................................................................................................................

Contents

About this document

Purpose ......................................................................................................................................................... v

Reason for revision ....................................................................................................................................... v

Intended audience ......................................................................................................................................... v

Supported systems ........................................................................................................................................ v

Safety information ........................................................................................................................................ v

Conventions used ......................................................................................................................................... vi

Eco-environmental statements ..................................................................................................................... vi

Technical support ......................................................................................................................................... vi

1 Installation Guide

Install the CPE ........................................................................................................................................... 1-1

ATroubleshooting

B TCP/IP configuration

C Product conformance

............................................................................................................................................................................................................................................................

iv Issue 1 February 2011

............................................................................................................................................................................................................................................................

v

Issue 1 February 2011

............................................................................................................................................................................................................................................................

About this document

Purpose

The purpose of the User Manual is to provide installation information, procedures for

installation, service activation and system reconfiguration for the DSL-6300V VDSL2

Bridge. Additionally the User Manual contains status indicators and troubleshooting

information and a comprehensive description of safety guidelines.

Reason for revision

This version 1.0 of the User Manual is the first issue.

Intended audience

The intended audience of the User Manual primarily is for individuals who install,

configure and maintain this customer premises equipment (CPE) and in addition

responsible for the supervision of transmission operation.

Supported systems

For theDSL-6300V VDSL2 gateway operation as described in this manual, a specific

hardware consists of the following components is required:

•One DSL-6300V VDSL2 Bridge

•One standard telephone cable

•One category 5 UTP network cable

•One power adapter

Safety information

Important! The following information lists the safety reminders for installation and

maintenance personnel.

Read all instructions before attempting to unpack, install, operate, or connect power to

this CPE. Please remember the following when you unpack and install this equipment:

•Always follow basic safety precautions to reduce the risk of fire, electrical shock

and injury.

•To prevent fire or shock hazard, do not expose the CPE to rain, moisture or install

this equipment near water. Never spill any form of liquid on or into this product.

............................................................................................................................................................................................................................................................

About this document

vi Issue 1 February 2011

............................................................................................................................................................................................................................................................

•Do not insert any sharp object into the products module openings or empty slots.

Doing so may accidentally damage its parts.

•Do not attach the power supply cable on building surfaces or floorings. Rest the

power cable freely without any obstacle or heavy items piled on top of it. Refrain

from abusing, stepping or walking on the cable.

•To protect the equipment from overheating, do not block the slots and openings in

the module housing that provide ventilation.

•Exercise caution when installing or modifying telephone lines. Never install

telephone wiring during inclement weather conditions (i.e., storm).

•Electrostatic discharge (ESD) can permanently damage semiconductor devices.

Always follow ESD-prevention guidelines for equipment handling and storage.

Conventions used

Important! Introduces important additional information.

CAUTION: Warns that a failure to follow the recommended procedure could result in loss of data or

damage to equipment.

WARNING: Warns that a failure to take appropriate safety precautions could result in physical injury.

In addition it warns of danger of electrical shock.

Eco-environmental statements

The statements that follow are the eco-environmental statements that apply to DSL-6300V

products.

Countries, states, localities, or other jurisdictions may require that systems be established

for the return and/or collection of packaging waste from the consumer, or other end user,

or from the waste stream. Additionally, reuse, recovery, and/or recycling targets for the

return and/or collection of the packaging waste may be established.

For more information regarding collection and recovery of packaging waste within

specific jurisdictions, please contact the D-Link Technologies Field Services/Installation

or Environmental Health and Safety organization.

Technical support

To obtain technical support, contact your local sales representative or use the Online

Customer Support (OLCS) (http://support.dlink.com).

1-1

Issue 1 February 2011

............................................................................................................................................................................................................................................................

1 Installation Guide

Overview

Purpose

This Installation Guide provides information about how to install the DSL-6300V VDSL2

Bridge at the customers premises, which may be apartment blocks, hotels or office

complexes.

This customer premises equipment (CPE) supports Ethernet-over-VDSL2 via one

Ethernet data link rated up to 100 Mbps symmetrically. With its bridge functionality, it

connects any device equipped with a 10BASE-T or 100BASE-TX network interface card

via a standard telephone cable to a VDSL switch. For this purpose, it provides:

•One VDSL port

•One Ethernet LAN port (10/100BASE-TX)

Contents

This chapter covers these topics.

Install the CPE

When to use

Use this procedure to install the DSL-6300V and to establish a connection. The following

figure shows the CPE with all external connections established. This will be described

step by step in the procedure below.

Install the CPE 1-1

............................................................................................................................................................................................................................................................

Install the CPEInstallation Guide

1-2 Issue 1 February 2011

............................................................................................................................................................................................................................................................

Figure 1-1 Overview about all external connections

System requirements and safety guidelines

1. The CPE should be located in a cool dry place, with at least 5 cm (2 in.) of space on all

sides for ventilation. Place the CPE out of direct sunlight, and away from heat sources

or areas with a high amount of electromagnetic interference.

2. For power supply, the CPE requires 15 V DC via the supplied power adapter.

3. Do not spill any liquid on this CPE.

4. The CPE is a plug-and-play unit and does not need any configuration or maintenance.

5. Do not place the CPE on an unstable stand or table; the CPE may drop and become

damaged.

6. For an Internet access, a PC with a 10/100 Mb/s Ethernet adapter card installed is

required. And it must be configured for a connection method which should be obtained

from the ISP. Please consult your ISP for connection requirement.

Before you begin

Make sure that the package content is complete. Preserve original carton and packaging

material.

Install the CPEInstallation Guide

............................................................................................................................................................................................................................................................

Issue 1 February 2011 1-3

............................................................................................................................................................................................................................................................

Mounting procedure

There are two ways for mounting the CPE:

•Wall mounting

1. Locate a high position on the wall that is free of obstructions.

2. Connect two screws in the wall 5 cm (2 in.) apart. Do not screw the screws all the

way into the wall.

Important! Make sure that the screws are securely fixed to the wall and strong

enough to hold the weight of the CPE.

screws specification for wall mounting:

3. Align the holes on the back of the CPE with the screws on the wall.

4. Hang up the CPE on the screws.

•Desktop mounting

Place the CPE on top of the desk with the name logo side up.

HW installation procedure

CAUTION:

Please follow the directions from your service provider regarding the connection of your

VDSL2 bridge. The following procedure are meant as a guideline.

........................................................................................................................................................................................................................

1Connect the cord of the AC power adapter to the power socket on the CPE which is

labeled 15 V 1 A. Then plug the power adapter directly into the AC power outlet.

Result: The LED (marked power) on the LED panel is on.

........................................................................................................................................................................................................................

2Restore this CPE to factory defaults if necessary. See section Reset switch to restore the

CPE to the factory defaults.

........................................................................................................................................................................................................................

3Connect one end of the attached standard telephone cable to the port on the CPE which is

labeled VDSL and connect the other end to the telephone wall outlet providing the VDSL

servive.

............................................................................................................................................................................................................................................................

Install the CPEInstallation Guide

1-4 Issue 1 February 2011

............................................................................................................................................................................................................................................................

........................................................................................................................................................................................................................

4Connect one end of the Category 5 UTP network cable to the Ethernet LAN port on the

CPE and the other end to the port of the network interface on the appropriate device, for

example a PC, Notebook and so on.

........................................................................................................................................................................................................................

5If you need to change the configuration of the gateway, make sure that the Ethernet

adapter of your device is correctly configured for Static IP. For more details refer to

Appendix B TCP/IP configuration.

........................................................................................................................................................................................................................

6Establish the first connection with your ISP. For information about how to configure an

internet connection, please consult your ISP.

........................................................................................................................................................

END OFSTEPS

D-Link DSL-6300V Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques