CyberPower CPS320SL Manuel utilisateur

User Manual for:

CPS320SL / CPS375SL / CPS500SL /

CPS575SL / CPS650SL

and PowerPanel™ Software

ADDITIONAL INSTALLATION TIPS CAN BE FOUND AT:

http://www.cyberpowersystems.com/faq_sl.htm

TABLE OF CONTENTS

Description……………………. ………1 LED Indicators……………………………..7

Determining Power Requirements…..1 Troubleshooting Guide……………………8

Hardware Installation Guide………….2 Specifications………………………………8

Software Installation Guide…………..3 Battery Replacement Instructions…….….9

Software User Manual………………..4 Warranty…………………………………...10

Thank you for purchasing a CyberPower Systems Product. To enjoy all the features and benefits of this Uninterruptible Power System

(UPS), please read and follow all installation and operation instructions completely. This UPS is designed to provide guaranteed power

protection for connected electronic equipment. The accompanying PowerPanel™ software saves data, closes open applications and

automatically shuts down your computer system in an intelligent and orderly manner.

IMPORTANT SAFETY INSTRUCTIONS

(SAVE THESE INSTRUCTIONS)

This manual contains important safety instructions. Please read and follow all instructions carefully during installation and

operation of unit. Read this manual thoroughly before attempting to unpack, install, or operate.

CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area, free of

conductive contaminants. (Please see specifications for acceptable temperature and humidity range).

CAUTION! To reduce the risk of electric shock, do not remove the cover except to service the battery. No user serviceable

parts inside except for battery.

CAUTION! Hazardous live parts inside can be energized by the battery even when the AC input power is disconnected.

CAUTION! UPS must be connected to an AC power outlet with fuse or circuit breaker protection. Do not plug into an outlet

that is not grounded. If you need to de-energize this equipment, turn off and unplug the unit.

CAUTION! To avoid electrical shock, turn off the unit and unplug it from the AC power source before servicing the battery or

installing a computer component.

DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! CyberPower Systems does not sell products for life

support or medical applications. DO NOT use in any circumstance that would affect operation or safety of any life support

equipment or with any medical applications or patient care.

DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire or electric shock, do not use with or near an

aquarium. Condensation from the aquarium can cause the unit to short out.

CPS320SL / CPS375SL / CPS500SL / CPS575SL / CPS650SL

Guaranteed Uninterruptible Power System

DESCRIPTION

INSPECTION

The box should contain the following:

(1) PowerPanel™ software (floppy disk); (1) serial interface cable (DB-9);

(1) telephone communication cable; (1) user manual; (1) warranty registration card;

(1) UPS unit.

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT

1. Make sure that the total Volt-Amp (VA) requirements of your computer, monitor and peripherals does not exceed 1440 VA.

2. Insure that the equipment plugged into the three battery power-supplied outlets does not exceed the UPS unit’s rated capacity

(320VA/185W for CPS320SL, 375VA/210W for CPS375SL, 500VA/275W for CPS500SL, 575VA/320W for CPS575SL and

650VA/350W for CPS650SL). If rated unit capacities are exceeded, an overload condition may occur and cause the UPS unit to

shut down and the circuit breaker to trip.

3. If the power requirements of your equipment are listed in units other than Volt-Amps (VA), convert Watts (W) or Amps (A) into VA

by doing the calculations below. Note: The below equation only calculates the maximum amount of VA that the equipment can

use, not what is typically used by the equipment at any one time. Users should expect usage requirements to be approximately

60% of below value.

TO ESTIMATE POWER REQUIREMENTS:

Watts (W) x 1.82 = VA or Amps (A) x 120 = VA

Add the totals up for all pieces of equipment and multiply this total by .6 to calculate actual requirements.

There are many factors that can effect the amount of power that your computer system will require. The total load that you will be

placing on the battery-powered outlets should not exceed 80% of the unit’s capacity.

XBattery/Surge Outlets

Provides three battery powered/surge outlets for connected

equipment and insures temporary uninterrupted operation

of your equipment during a power failure.

YFull-Time Surge Protection Outlets

Provides three always on surge suppression outlets.

ZPower Switch

Can be used as a mater on/off switch for equipment

connected to the battery power supplied outlets.

[Electrical Wiring Fault Indicator

This LED indicator will illuminate to warn the user that a

wiring problem exists, such as bad ground, miss ground or

reversed wiring. If this is illuminated, user is advised to

disconnect all electrical equipment from the outlet and have

an electrician check to ensure the outlet is properly wired.

\Power On Indicator

This LED is illuminated when the utility condition is normal

and the UPS outlets are providing power, free of surges

and spikes.

]Circuit Breaker

Located on the side of the UPS, the circuit breaker serves to

provide overload and fault protection. Under normal operating

conditions, the circuit breaker is depressed.

^Serial Port to PC

This port allows connection and communication from the DB-9

serial port on the computer to the UPS unit. The UPS

communicates its status to the PowerPanel™ software. This

interface is also compatible with the UPS service provided by

Windows NT and Windows 2000.

_Communication Protection Ports

Communication protection ports will protect any standard modem,

fax or telephone line.

`Outlets Designed for AC Adapters

Allows six AC power adapter blocks to be plugged into the UPS

without blocking adjacent outlets.

HARDWARE INSTALLATION GUIDE

1. Your new UPS may be used immediately upon receipt. However, recharging the battery for at least four hours is

recommended to insure that the battery’s maximum charge capacity is achieved. Charge loss may occur during shipping and

storage. To recharge the battery, simply leave the unit plugged into an AC outlet. The unit will charge in both the on as well as

the off position.

2. If you wish to use the software, connect the enclosed serial interface cable to the serial port on the UPS and an open serial port

on the computer. If you are not going to use the software, you do not need to connect the cable.

3. With the UPS unit off and unplugged, connect your computer, monitor, and any externally powered data storage device (Zip drive,

Jazz drive, Tape drive, etc…) into the battery power supplied outlets. Plug your peripheral equipment (printer, scanner, speakers)

into the full-time surge protection outlets. DO NOT plug a laser printer, copier, space heater, vacuum or other large

electrical device into the UPS. The power demands of these devices will overload and possibly damage the unit.

4. To protect a fax, phone or modem, connect a telephone cable from the wall jack outlet to the in jack of the UPS. Connect a

telephone cable from the out jack with the CPU icon to the modem port on your computer.

The out jack with the telephone icon can be used to protect a telephone or fax machine.

5. Plug the UPS into a 2 pole, 3 wire grounding receptacle (wall outlet). Make sure the wall branch outlet is protected by a fuse or

circuit breaker and does not service equipment with large electrical demands (e.g. refrigerator, copier, etc…). Avoid using

extension cords. If used, the extension cord must be rated for 15 amps.

6. Depress the power switch to turn the unit on. The power on indicator light will illuminate and the unit will “beep” once.

7. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this, turn the UPS off and

unplug at least one piece of equipment from the battery power supplied outlets. Wait 10 seconds. Make sure the circuit breaker

is depressed and then turn the UPS on.

8. Your UPS is equipped with an auto-charge feature. When the UPS is plugged into an AC outlet, the battery will automatically

recharge.

9. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.

10. To store your UPS for an extended period, cover it and store with the battery fully charged. Recharge the battery every three

months to insure battery life.

CPS320SL / CPS375SL / CPS500SL / CPS575SL / CPS650SL

Guaranteed Uninterruptible Power System

POWERPANEL™ SOFTWARE INSTALLATION GUIDE

(Note: Use of the software is optional. The UPS will provide surge suppression and battery backup without the software. You must use

the software if you wish to have the automatic shutdown feature).

FOR WINDOWS 95/98/Me

1. Turn the UPS off and unplug it.

2. Connect the serial interface cable to the UPS and an open serial port on the back of the computer. (Note: You must use the

serial cable that was supplied with the unit).

3. Plug the UPS into an AC outlet, turn the UPS on and then start your computer.

4. Click on Start, point to Settings, then click Control Panel.

5. Double-click on Add/Remove Programs.

6. Insert the software disk into the floppy drive.

7. Click Install.

8. Follow the on-screen instructions.

9. Once the software is installed, remove the floppy disk and restart your computer.

When your computer restarts, the PowerPanel™ software will appear on your screen for a few seconds, and then minimize. It will

appear as a blue and white battery icon located in the system tray, near the clock.

FOR WINDOWS NT

1. Click on Start, point to Settings, then Control Panel.

2. Double-click on the UPS Icon.

3. Remove the check mark from the box labeled UPS is installed on.

4. Click OK.

5. Acknowledge the message that the UPS is in an unknown state.

6. Exit to the desktop.

7. Shutdown your computer.

8. Turn the UPS off and unplug it.

9. Connect the serial interface cable to the UPS and an open serial port on the back of your computer. (Note: You must use the

cable that was supplied with the unit).

10. Plug the UPS into an AC outlet, turn the UPS on and then start your computer.

11. Click on Start, point to Settings, then Control Panel.

12. Double-click on Add/Remove Programs.

13. Insert the software disk into the floppy drive.

14. Click Install.

15. Follow the on-screen instructions.

16. Once the software is installed, remove the floppy disk and restart your computer.

When your computer restarts, the PowerPanel™ software will appear on your screen for a few seconds, and then minimize. It will

appear as a blue and white battery icon located in the system tray, near the clock.

FOR WINDOWS 2000

1. Click on Start, point to Settings, then Control Panel.

2. Double-click on Power Options.

3. On the UPS Tab, click Select.

4. In the UPS Selection Dialog Box, under Manufacturers, click None.

5. Exit to the desktop.

6. Shutdown the computer.

7. Turn the UPS off and unplug it.

8. Connect the serial interface cable to the UPS and an open serial port on the back of your computer. (Note: You must use the

cable that was supplied with the unit).

9. Plug the UPS into an AC outlet, turn the UPS on and then start your computer.

10. Click on Start, point to Settings, then Control Panel.

11. Double-click on Add/Remove Programs.

12. Insert the software disk into the floppy drive.

13. Click Install.

14. Follow the on-screen instructions.

15. Once the software is installed, remove the floppy disk and restart your computer.

When your computer restarts, the PowerPanel™ software will appear on your screen for a few seconds, and then minimize. It will

appear as a blue and white battery icon located in the system tray, near the clock.

POWERPANEL™ SOFTWARE USER MANUAL

OVERVIEW

PowerPanel™ version 2.03 or greater is designed for use with Windows 95, Windows 98, Windows Me, Windows NT and Windows 2000.

The latest version can be downloaded from www.cyberpowersystems.com/downloads.htm. It works in conjunction with the UPS to provide

full protection of valuable computer systems, applications and data. In the event of a power failure, PowerPanel™ automatically saves and

closes open files under auto-assigned file names or existing files names after a software controlled delay. The computer and UPS are

automatically shutdown to conserve battery power. Files with auto-assigned names will be saved under C:\PCTemp, where Cis the name

of your main hard drive. Files that have previously been saved will be saved in their original location.

PowerPanel™ is equipped with a Scheduled Shutdown feature which can automatically save and close open files and then shutdown the

computer and UPS at a user specified date and time. Use of this feature is optional and is not required for the power failure shutdown to

occur.

The use of the PowerPanel™ software is optional. The UPS unit will provide full surge suppression and battery backup without the

software. You must use the software if you wish to have the automatic shutdown feature.

POWERPANEL™ MAIN WINDOW DESCIPTION

1. Minimize Button: This button is used to minimize the software.

2. Power Button: Clicking on the power button will stop the software.

3. Setup Button: Click the setup button to open the Setup Window.

4. Log Button: Click on the log button to open the Log Window.

5. Shutdown Button: Click the shutdown button to open the Scheduled Shutdown Window.

6. Battery OK Indicator: This indicator appears in a green color when AC power is normal and the unit and software are

communicating.

7. AC Power Indicator: This indicator appears in a green color when AC power in normal. When the power fails, the indicator will

change to a red color with an “X” through it.

8. Scheduled Shutdown: If there is a shutdown scheduled within seven days, the information will be displayed here. The user can

schedule a shutdown in the Scheduled Shutdown Window.

9. Final Countdown: When the final countdown timer reaches zero, the software will begin shutting down the system. This can be

adjusted in the Setup Window.

POWERPANEL™ SETUP WINDOW

1. Delay Between Warning Messages: This setting determines the delay between the audible alarms.

2. Time Between Power Failure and Initial Warning: This setting determines the delay between when the power fails and the first

audible alarm.

CPS320SL / CPS375SL / CPS500SL / CPS575SL / CPS650SL

Guaranteed Uninterruptible Power System

3. Time Between Power Failure and Shutdown Process: This user adjustable setting determines how long the UPS will run on

battery before starting to shut down the system. If this is not checked, the unit will run on battery until the low battery condition is

met (2 minutes of backup time remaining), and then start the shutdown process. If the low battery condition is met before this

timer reaches zero, the software will start the shutdown process.

4. UPS is Installed On: This shows the current COM port that the UPS is using. The port assigned to the UPS needs to be used

exclusively for the PowerPanel™ software.

5. OK Button: This button is used to exit the setup window and save any changes.

6. Cancel Button: This button is used to exit the setup window without saving any changes.

7. About Button: This button will display information about the software as well as contact information.

POWERPANEL™ LOG WINDOW

1. Display Window: This area displays either the Event Log or the Closed Application Information.

2. Event Log: Select this option to view PowerPanel™ events such as program start, program end, power failure and low battery.

3. Closed Application Information: Select this option to view the file names of applications that were saved by PowerPanel™.

Please note: If an application has an existing file name, it will be saved under that file name and not appear in this window.

4. OK Button: This button is used to exit the window.

5. Clear Button: This button is used to clear the information in the selected log.

POWERPANEL™ SHUTDOWN WINDOW

1. Display Window: Any schedule information will be displayed here.

2. Special Setting: This option is used to schedule a shutdown at a specific date and time.

3. Weekly Setting: This option is used to schedule a shutdown for a specific time and day of the week.

4. OK Button: This button is used to exit the window.

5. Add Button: This button is used to add an item to the schedule.

6. Clear Button: This button is used to delete the selected item.

7. Cancel Shutdown: This button is used to cancel the current shutdown.

8. Day, Date and Time: This is the area where you select the day, date and time that you want the shutdown to occur. Once you

have selected it, click the Add Button to add the item to the schedule.

Please note: The use of the schedule is optional and will have no effect on the shutdown of your system during a power failure. This

feature is simply used if you want have your computer automatically shut down at a scheduled time.

USING THE WINDOWS NT UPS SERVICE

If you are running Windows NT, you may choose to use the Windows NT service instead of PowerPanel™. You can run either

PowerPanel™ or the NT service, but not both.

To Configure the Windows NT UPS Service:

1. Click on Start, point to Settings, then Control Panel.

2. Double-click the UPS Icon.

3. Select the COM port that the UPS is connected to.

4. Set the Power Failure Signal to Negative.

5. Set the Low Battery Signal to Negative.

6. Set the Remote UPS Shutdown Signal to Positive.

7. Click OK.

Please note: This service must be stopped in order to use the PowerPanel™ software. To stop the service, remove the checkmark from

Uninterruptible Power Supply is installed on. Click OK. Acknowledge the message that the UPS is in an unknown state and exit to the

desktop.

USING THE WINDOWS 2000 UPS SERVICE

If you are running Windows 2000, you may choose to run the Windows 2000 UPS service instead of PowerPanel™. You can run either

PowerPanel™ or the Windows 2000 UPS service, but not both.

To Configure the Windows 2000 UPS Service:

1. Click on Start, point to Settings, then Control Panel.

2. Double-click on Power Options.

3. On the UPS Tab, click Select.

4. In the UPS Selection Dialog Box, under Select Manufacturer, select Generic.

5. Under Select Model, select Custom.

6. On the UPS Tab, click Configure.

7. Set Power Fail/On Battery to Negative.

8. Set Low Battery to Negative.

9. Set UPS Shutdown to Positive.

10. Click OK.

Please note: This service must be stopped in order to run PowerPanel™. To disable the service, set the Manufacturer to None.

Please note: You must be logged on as an administrator or a member of the administrator’s group to make these changes. Network

policies may also prevent you from making these changes. Please contact your network administrator for further assistance.

TESTING YOUR UPS SYSTEM

Once you have set up your UPS system, you may wish to test it. Make sure that the UPS has been charged for at least 4 hours before

performing this test.

If you are using PowerPanel™:

1. With your UPS and computer on, open an application such as notepad.

2. Enter some data into the application.

3. Unplug the UPS from the AC outlet.

When a power failure occurs, PowerPanel™ will appear on the screen. The outlet and battery symbols will change to indicate a power

failure. The countdown timer will move towards zero. When the timer reaches zero, the software will begin to save and close any open

applications. The software will auto-assign names to any files that have not been previously saved, and then save the file to the PCTemp

folder which is located in the root directory of your C drive (where Cis the name of your main hard drive). Once all open files have been

saved and closed, PowerPanel™ will shutdown the operating system. Once the operating system is shutdown, the UPS will turn off within

90 seconds. Wait until the UPS has turned off before plugging the UPS back into the outlet.

Once the test has been completed, plug the UPS back into the wall and turn it back on. You may then restart your computer. Please allow

4 hours for the UPS to recharge before attempting another self-test.

If you are NOT using PowerPanel™:

1. Have your computer and UPS turned on.

2. Unplug the UPS from the wall to simulate a power failure.

3. The UPS will begin beeping, indicating a power failure.

4. Save and close any open files.

5. Shut down the operating system.

6. Once the computer system is shutdown, turn the UPS off.

As the battery discharges, the unit will beep more rapidly, indicating that the battery is nearing discharge. Once the test is complete, plug

the UPS back in and start your computer. Please allow 4 hours for the UPS to recharge before attempting another self-test.

CPS320SL / CPS375SL / CPS500SL / CPS575SL / CPS650SL

Guaranteed Uninterruptible Power System

DEFINITIONS FOR ILLUMINATED LED INDICATORS

CONDITION

On Off Set Off

Off On/Off Set Two Beeps Utility Failure- the UPS is providing

power to battery power-supplied outlets

from its battery.

Off On/Off Set Rapid

Beeps Utility Failure- The UPS is providing

battery power. Rapid beeps indicate

the unit will run out of power shortly.

Off Off Up Two Beeps

Rapid

Beeps

System Overload- Occurs when

connected equipment exceeds the

rating of unit. Turn the UPS off, unplug

at least one piece of equipment, wait 10

seconds, reset the circuit breaker and

turn the unit on.

Off On/Off Set Long Beep Battery Overload- Occurs when

connected equipment exceeds the

rating of battery outlets of the unit.

Turn the UPS off, unplug at least one

piece of equipment from battery outlets,

wait 10 seconds, reset the circuit

breaker and turn the unit on.

On/Off On Set None Electrical Wiring Fault- This indicates

a wiring problem with the AC outlet

such as bad ground, miss ground, or

reversed wiring. User is advised to

disconnect all electrical equipment from

the outlet and have an electrician check

the outlet to insure proper wiring.

TROUBLESHOOTING

Problem

Possible Cause

Solution

Full-time surge protection

outlets stop providing

power to equipment.

Circuit breaker has tripped

due to an overload.

Turn the UPS off and unplug at least one piece of

equipment. Wait 10 seconds, reset the circuit

breaker by depressing the button, and then turn the

UPS on.

Battery not fully charged. Recharge the battery by leaving the UPS plugged

in.

The UPS does not

perform expected runtime.

Battery is slightly worn

out. Contact CyberPower Systems about replacement

batteries at [email protected]

The on/off switch is

designed to prevent

damage by rapidly turning

it off and on.

Turn the UPS off. Wait 10 seconds and then turn

the UPS on.

The unit is not connected

to an AC outlet. The unit must be connected to a 110/120v 60Hz

outlet.

The battery is worn out. Contact CyberPower Systems about replacement

batteries at [email protected]

The UPS will not turn on.

Mechanical problem. Contact CyberPower Systems at

[email protected]

The serial cable is not

connected. Connect the serial cable to the UPS unit and an

open serial port on the back of the computer. You

must use the cable that came with the unit.

The serial cable is

connected to the wrong

port.

Check the back of the computer for an additional

serial port. Move the cable to this port.

The unit is not providing

battery power. Shutdown your computer and turn the UPS off.

Wait 10 seconds and turn the UPS back on. This

should reset the unit.

PowerPanel™ is inactive

(all icons are gray).

The serial cable is not the

cable that was included

with the UPS unit.

You must use the serial cable that was enclosed

with the unit for the software and unit to be able to

communicate.

SPECIFICATIONS

CPS320SL CPS375SL CPS500SL CPS575SL CPS650SL

Capacity 320VA

(185W) 375VA

(210W) 500VA

(275W) 575VA

(320W) 650VA

(350W)

Input Voltage on Utility 100V to 140V

Input Frequency 57 Hz to 63 Hz

On-Battery Output Voltage 120Vac ± 5%

Transfer Time 4ms Typical

Max. Load for UPS Outlets

(3 Outlets) 320VA

(185W) 375VA

(210W) 500VA

(275W) 575VA

(320W) 650VA

(350W)

Max. Load for Full-Time Surge

Protection outlets (6 Outlets) 12 Amps

On-Battery Output Wave Form Simulated Sine Wave Form

Operating Temperature + 32°F to 95° F. (0° C to 35° C)

Operating Relative Humidity 0 to 95% NON-CONDENSING

Size (Length x Width x Height) 9 7/8” x 6 3/16” x 3 1/8” (25.8cm x 15.9cm x 8.3cm)

Net Weight 10lbs. 10 lbs. 13 13 lbs. 14 lbs.

Typical Battery Recharge Time 8 hours typical from total discharge

Typical Battery Life 3 to 6 years, depending on number of discharge/recharge cycles

Battery Type 12V / 3AH 12V / 4AH 12V / 7AH 12V / 7.2AH 12V / 7.5AH

Recommended Battery Spill-proof, Maintenance-free, sealed lead-acid

Safety Approvals UL1778(UPS), CUL107.1/FCC/DoC Class B

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels CyberPower UPS

CyberPower

CyberPower UT650E-FR/UPS Manuel utilisateur

CyberPower

CyberPower LE850G Manuel utilisateur

CyberPower

CyberPower OL6000ERT3U Manuel utilisateur

CyberPower

CyberPower PR750LCDRTXL2U Manuel utilisateur

CyberPower

CyberPower 649532005505 Manuel utilisateur

CyberPower

CyberPower CPS1100AVR Manuel utilisateur

CyberPower

CyberPower OLS5200E Manuel utilisateur

CyberPower

CyberPower CPS600E Manuel utilisateur

CyberPower

CyberPower BH900 Manuel utilisateur

CyberPower

CyberPower BU600E Manuel utilisateur

CyberPower

CyberPower OR1500PFCRT2U Manuel utilisateur

CyberPower

CyberPower CST625G Manuel utilisateur

CyberPower

CyberPower OL6000RT3U Manuel utilisateur

CyberPower

CyberPower PR3000LCDRT2U Manuel utilisateur

CyberPower

CyberPower Value1200EILCD Manuel utilisateur

CyberPower

CyberPower CST1400G Manuel utilisateur

CyberPower

CyberPower RT650 Manuel utilisateur

CyberPower

CyberPower OLS6000ERT6UA Manuel utilisateur

CyberPower

CyberPower CP600LCD Manuel

CyberPower

CyberPower UPS BR850ELCD Manuel utilisateur

CyberPower

CyberPower OL6000RT3UPDU Manuel utilisateur

CyberPower

CyberPower OR1500LCDRTXL2U Manuel d'utilisation et d'entretien

CyberPower

CyberPower CyberShield BAS34U24V Manuel utilisateur

CyberPower

CyberPower OP850 Manuel utilisateur

Manuels UPS populaires d'autres marques

Pylontech

Pylontech Victron & Pylontech US5000 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur

Mecer

Mecer ME-1000-WTU Manuel utilisateur

Mustek

Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation

Emerson

Emerson Liebert NXL series Manuel utilisateur

MAKELSAN

MAKELSAN BOXER SERIES Manuel utilisateur

Block

Block PC-0524-400-0 Manuel utilisateur

Eaton

Eaton 3S Instructions de montage

Best Power

Best Power 610 Manuel utilisateur

Best Power

Best Power Unity/I UT3K Manuel utilisateur

Mustek

Mustek PowerMust 400 Offline Manuel utilisateur

Xantrex

Xantrex Trace 512 UR-UPS Manuel utilisateur

Forza

Forza SL-1501UL Manuel utilisateur

LEGRAND

LEGRAND keor 310081 Manuel utilisateur

ABB

ABB Conceptpower DPA 500 Manuel utilisateur

ZincFive

ZincFive BC Series Manuel utilisateur

BPC

BPC 1.5K SMART Manuel utilisateur

IBM

IBM 5595-1AX Manuel utilisateur