CyberPower PR3000 Manuel utilisateur

User’s Manual

Professional Rack Mount UPS

PR3000

ADDITIONAL INSTALLATION TIPS CAN BE FOUND AT:

www.cyberpowersystems.com

TABLE OF CONTENTS

SAFETY WARNINGS……………………………………………….….………….3

BLOCK DIAGRAM……………………..………………………………………….4

INSTALLATION………………..……………………………….…………………..4

- UNPACKING………...……………………………………………………….4

- HOW TO DERTERMINE THE POWER REQUIREMENTS OF YOUR

EQUIPMENT…………………………………………………………………4

- TO ESTIMATE POWER REQUIREMENTS………………………………5

- HARDWARE INSTALLATION………………………………………………5

BASIC OPERTAION……………………….………………………………………8

-FRONT PANEL DESCRIPTION……………………….……………………8

-REAR PANEL DESCRIPTION…………….………………………………..9

TROUBLESHOOTING……..………………………..…………..……..…..….…12

TECHNICAL SPECIFICATION…………………………………….…………….13

DEFINITIONS FOR ILLUMINATED LED INDICATORS…………………..….14

BATTERY REPLACEMENT……..……………..…………………………..…….15

- BATTERY REPLACEMENT PROCEDURES……………………………16

LIMITED WARRANTY AND CONNECTED EQUIPMENT

GUARANTEE……….…... …….…... …….…... …….…... …….…... …….…...18

PR3000

Guaranteed Uninterruptible Power System

SAFETY WARNINGS

zThis manual contains important safety instructions. Please read and follow all

instructions carefully during installation and operation of the unit. Read this

manual thoroughly before attempting to unpack, install, or operate.

zThe AC power outlet must be installed near the ups and must be easily

accessible.

zAttention, risk of electric shock. Disconnecting this unit from the power mains,

does not remove the risk. Voltage may still be present from the battery pack. The

battery pack quick connectors should be disconnected before peforming

maintenance or service work on the UPS.

zWhen replacing the batteries, use the same number and type of batteries

zDo not open or mutilate the battery or batteries. Electrolyte is harmful to the skin

and eyes.

zA battery can present a risk of electric shock and high short circuit current. The

following precaution should be observed when working on batteries

- Remove watches, rings or other metal objects.

- Use tools with insulated handles.

- Never short circuit the battery terminals.

BLOCK DIAGRAM

INSTALLATION

UNPACKING

Inspect the UPS upon receipt. The box should contain the following:

(1) UPS Unit; (1) User’s Manual; (2) Rack Mount Brackets; (2) Stands;

(1) PowerPanel Plus Software Disk; (1) PowerPanel Software Disk; (1) Telephone

Cable; (2) Serial Interface Cables (DB-9); (1) Serial-to-USB cable

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR

EQUIPMENT

1. Insure that the equipment plugged into the five battery power-supplied outlets does

not exceed the UPS unit’s rated capacity (3000VA/2200W for PR3000,). If rated

unit capacities are exceeded, an overload condition may occur and cause the UPS

unit to shut down or the circuit breaker to trip.

2. If the power requirements of your equipment are listed in units other than

Volt-Amps (VA), convert Watts (W) or Amps (A) into VA by doing the calculations

below. Note: The below equation only calculates the maximum amount of VA that

the equipment can use, not what is typically used by the equipment at any one

time. Users should expect usage requirements to be approximately 60% of the

maximum value.

PR3000

Guaranteed Uninterruptible Power System

TO ESTIMATE POWER REQUIREMENTS:

1. ______Watts (W) x 2.0 = _____VA or _____Amps (A) x 120 = _____VA

2. Add the totals up for all pieces of equipment and multiply this total by 0.6 to

calculate actual requirements. There are many factors that can affect the amount

of power that your computer system will require. The total load that you will be

placing on the battery-powered outlets should not exceed 80% of the unit’s

capacity.

HARDWARE INSTALLATION

1. Your new UPS may be used immediately upon receipt.

However, recharging the battery for at least four hours is

recommended to insure that the batteries are fully charged.

Charge loss may occur during shipping and storage. To

recharge the battery, simply leave the unit plugged into an

AC outlet. The unit will charge in both the on as well as the

off position.

2. If you wish to use the software, connect the

enclosed serial interface cable to the serial

port on the UPS and an open serial port on the

computer. If you would like to use USB

interface, please connect the USB adapter

with the serial cable then connect the USB

adapter to your computer.

3. With the UPS unit off and unplugged, connect your computer,

monitor, and any other devices into the battery power

supplied outlets. DO NOT plug a laser printer, copier, space

heater, vacuum, paper shredder or other large electrical

device into the UPS. The power demands of these devices

will overload and possibly damage the unit.

4. To surge protect a network connection, connect a network cable from the wall jack

outlet to the IN jack of the UPS. Then connect a network cable from the OUT jack

on the UPS to the network device.

5. Plug the UPS into a wall outlet. Make sure the wall branch outlet is protected by a

fuse or circuit breaker and does not service equipment with large electrical

demands (e.g. refrigerator, copier, etc…). Avoid using extension cords. If used,

the extension cord must be rated for 30 Amps.

6. Depress the power switch to turn the unit on. The power on indicator light will

illuminate.

7. Your UPS is equipped with an auto-charge feature. When the UPS is plugged into

an AC outlet, the battery will automatically recharge.

8. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all

times.

9. To store your UPS for an extended period, cover it and store with the battery fully

charged. Recharge the batteries every three months to insure battery life.

10. To connect auxillary battery pack :

(a.) Remove the protection cover on the UPS rear panel.

(b.) Connect the black wire and the red wire of the Battery Pack to the

negative (-) / black terminal and the positive (+) / red terminal of the

PR3000 respectively. (See Figure 1)

**Note: Due to the large current, make sure to connect the positive to positive

and the negative to negative. Otherwise, it may cause a short circuit and the

unit may be irreversibly damaged.

PR3000

Guaranteed Uninterruptible Power System

Figure 1: Connecting PR3000 with Battery Pack

BASIC OPERATION

FRONT PANEL DESCRIPTION

 Power Switch

Press the power button to turn the UPS ON or OFF

 Test Switch The PR-UPS performs a self-test automatically when power on.

If the UPS passes the test, it returns to on-line operation. If the

UPS fails the self-test, please recharge the battery for 4 hours

and perform another self-test. If it fails after recharging the

battery, please replace the battery.

 Battery Indicators

This indicator shows a visual indication of the battery charge. If

battery capacity is under 20%, no indicator LED will illuminate

and UPS starts beeping.

PR3000

Guaranteed Uninterruptible Power System

 Load Level Indicators

This indicator shows a visual depiction of the UPS load. The load

indicator LED will turn orange if the load is between 80 and 100%.

If the load is under 20%, no indicator LED will illuminate.

 Power On Indicator

This LED is illuminated when the utility condition is normal and

the UPS outlets are providing “clean power”, free of surges and

spikes.

Battery Indicator

This illuminates during utility failure, indicating that the battery is

supplying power to the battery-power supplied outlets.



AVR Indicator This LED indicates that the UPS is operating in automatic voltage

regulation mode. When the led is illuminated continuously, it

indicates input over-voltage and the UPS unit bucks the voltage.

When the led is flashed in rotation, it indicates that the UPS unit

is boosting input voltage.

REAR PANEL DESCRIPTION

 Circuit Breaker Reset for Overload Protection

Re-settable circuit breakers provide optimal overload protection.

Battery Backup and Surge Protection Outlets

Provides two battery powered, surge protected and AVR

outlets for connected equipment and insures uninterrupted

operation of connected equipment during a power failure.

Individual Backup Power for Critical Load

Provides a battery powered, surge protected and AVR

outlet for the most critical connected equipment and insures

uninterrupted operation of connected equipment during a

power failure.

** NOTE: When the UPS is overloaded, the other two minor outlets will not provide

power to equipment,.

Communication Protection Ports

Ethernet RJ-45 Network Protection Ports protect standard

network cables.

Autres manuels pour PR3000

Table des matières

Autres manuels CyberPower UPS

CyberPower

CyberPower SE450G Manuel utilisateur

CyberPower

CyberPower 649532004256 Manuel utilisateur

CyberPower

CyberPower BU1000E Manuel utilisateur

CyberPower

CyberPower BL1450U Manuel utilisateur

CyberPower

CyberPower 400E-GP Manuel utilisateur

CyberPower

CyberPower UT650EG Manuel utilisateur

CyberPower

CyberPower CP1350PFCLCD Manuel utilisateur

CyberPower

CyberPower OP850 Manuel utilisateur

CyberPower

CyberPower 649532822027 Manuel utilisateur

CyberPower

CyberPower PR750ELCDRT1U Manuel utilisateur

CyberPower

CyberPower Paragon OL3000RMXL2U Manuel utilisateur

CyberPower

CyberPower OR1500LCDRTXL2U Manuel d'utilisation et d'entretien

CyberPower

CyberPower SMP1400EILCD Manuel utilisateur

CyberPower

CyberPower PR750LCDRM1U Manuel utilisateur

CyberPower

CyberPower CPS1500AVR Manuel utilisateur

CyberPower

CyberPower ST425 Manuel utilisateur

CyberPower

CyberPower OL6000ERT3U Manuel utilisateur

CyberPower

CyberPower OL6KERT3UDPM Manuel utilisateur

CyberPower

CyberPower CP625HG Manuel utilisateur

CyberPower

CyberPower CyberShield CSN27U12V-NA3-G Manuel utilisateur

CyberPower

CyberPower Value1200ELCD Manuel utilisateur

CyberPower

CyberPower PR1500 Manuel utilisateur

CyberPower

CyberPower CP825LCD Manuel utilisateur

CyberPower

CyberPower CPS1000EI Manuel utilisateur

Manuels UPS populaires d'autres marques

Pylontech

Pylontech Victron & Pylontech US5000 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur

Mecer

Mecer ME-1000-WTU Manuel utilisateur

Mustek

Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation

Emerson

Emerson Liebert NXL series Manuel utilisateur

MAKELSAN

MAKELSAN BOXER SERIES Manuel utilisateur

Block

Block PC-0524-400-0 Manuel utilisateur

Eaton

Eaton 3S Instructions de montage

Best Power

Best Power 610 Manuel utilisateur

Best Power

Best Power Unity/I UT3K Manuel utilisateur

Mustek

Mustek PowerMust 400 Offline Manuel utilisateur

Xantrex

Xantrex Trace 512 UR-UPS Manuel utilisateur

Forza

Forza SL-1501UL Manuel utilisateur

LEGRAND

LEGRAND keor 310081 Manuel utilisateur

ABB

ABB Conceptpower DPA 500 Manuel utilisateur

ZincFive

ZincFive BC Series Manuel utilisateur

BPC

BPC 1.5K SMART Manuel utilisateur

IBM

IBM 5595-1AX Manuel utilisateur