CyberData 11171 Manuel

The IP Endpoint Company

Installation Quick Reference

VoIP V3 Zone Controller:

4-Port Audio Out

SIP Compliant

011171

Mounting

Contacting CyberData

Drill Hole Size for Anchor Installation: 3/16" (0.1875")

You have the option to use the following mounting template to mark, and then drill two 3/16" (0.1875”) holes for the

plastic ribbed anchors.

To install and mount the V3 Zone Controller:

1. Install the plastic ribbed anchors in the holes, and position the V3 Zone Controller mounting holes over the

anchors.

2. Use the two #6 x 1 1/2" screws to secure the V3 Zone Controller onto the mounting surface.

Sales: (831) 373-2601 ext. 334

Support: 831-373-2601 ext. 333

Web: http://www.cyberdata.net/support/contactsupportvoip.html

RMA Dept: (831) 373-2601 ext. 136

Email: [email protected]

RMA Status: http://www.cyberdata.net/support/rmastatus.html

Warranty and RMA information is available at the following website:

http://www.cyberdata.net/support/warranty/index.html

Corporate Headquarters

CyberData Corporation

3 Justin Court

Monterey, CA 93940, USA

Phone: 831-373-2601

Fax: 831-373-4193

www.CyberData.net

The VoIP V3 Zone Controller with Audio-Out enables access to existing paging speakers through a VoIP phone system.

The interface is designed to use a standard paging amplifier with audio inputs and supports paging up to 15 zone

groups from a VoIP phone.

Getting Started

• Be sure that you have received all the parts described in the Parts List section.

• Download the VoIP V3 Zone Controller Operations Guide from the following website address:

http://www.cyberdata.net/products/voip/legacyanalog/pagingzonev3/docs.html

Parts List

Product Specifications

Regulatory Compliance FCC Class A, UL 60950, CE

Power Requirement PoE or +48VDC

LAN Speed 10/100 Mbps

Protocol SIP compliant

Part Number 011171

Dimensions 6.11”L x 4.05”W x 1.15” H

Weight 1.2 lbs.

(2) #6 Plastic Ribbed Anchors (2) #6 x 1 1/2" Screws

(1) Mounting Template (see the last page)

(1) Mounting Kit

(1) VoIP Zone Controller - 4-Port Audio Out

Verifying Operations and Settings

To restore the V3 Zone Controller’s factory default

settings:

1. Use a paper clip to press and hold the RTFM

switch while all of the indicator LEDs turn off.

See the picture on the right.

2. Continue to press the RTFM switch until after

the indicator LEDs turn back on.

3. Release the RTFM switch. All of the V3 Zone

Controller settings will be restored to the

factory default settings.

4. The unit reboots.

Front View with LEDs

Back View with RTFM Switch

Status

(GREEN LED)

Power Status

(BLUE LED)

Link

(YELLOW LED)

Activity

(GREEN LED)

The round, BLUE Power Status LED on the front of the V3 Zone Controller comes on indicating that the

power is on.

The square, YELLOW Link LED above the Ethernet port indicates that the network connection has been

established. The Link LED changes color to confirm the auto-negotiated connection speed:

•ThisLEDisYELLOW at 10 Mbps.

•ThisLEDisORANGE at 100 Mbps.

The GREEN Status LED comes on after the device is booted and initialized. This LED blinks when a page

is in progress.

The square, GREEN Activity LED blinks when there is network activity.

Paper clip RTFM switch

Typical Zone Controller Setup Using the V3 Zone Controller

Setting Up the VoIP V3 Zone Controller

Generic PoE Switch

12 34 56

IP Phone

IP PBX Server

VoIP V3 Zone Controller 4-Port Audio Out

Analog Amplifiers Paging Speakers

Non PoE (with 48 VDC power supply)

Chassis Ground

PoE

To set up the V3 Zone Controller, connect the

device to your network:

Poe

•ForPoE, plug one end of an 802.3af Ethernet

cable into the V3 Zone Controller Ethernet

port. Plug the other end of the Ethernet cable

into your network. See the figure on the left.

Non-Poe

•ForNon-PoE, connect the V3 Zone Controller

to a 48VDC power supply. See the figure on

the left.

Chassis Ground

• If required, connect the earth grounding wire

to the Chassis Ground. See the figure on the

left.

48VDC

Autres manuels pour 11171

Autres manuels CyberData Changer

CyberData

CyberData 11006 Manuel utilisateur

CyberData

CyberData 011539 Manuel

CyberData

CyberData 011539 Manuel

CyberData

CyberData 011187 Manuel

CyberData

CyberData KS-1000 Manuel utilisateur

CyberData

CyberData 10630 Manuel utilisateur

CyberData

CyberData 011508 Manuel

CyberData

CyberData 10776 Manuel utilisateur

CyberData

CyberData 10845 Manuel utilisateur

CyberData

CyberData RS232 Manuel utilisateur

CyberData

CyberData 4-Port Powered USB 2.0 Hub 010845 Manuel utilisateur

CyberData

CyberData 011539 Manuel

CyberData

CyberData 11187 Manuel

CyberData

CyberData 10630 Manuel utilisateur

CyberData

CyberData IBM SI/O Manuel utilisateur

CyberData

CyberData 4-Port PoweredUSB 2.0 Hub 011006 Manuel utilisateur

CyberData

CyberData 10845 Manuel utilisateur

CyberData

CyberData 10807 Manuel utilisateur

CyberData

CyberData 10807 Manuel utilisateur

CyberData

CyberData 011236 Manuel

CyberData

CyberData 10807 Manuel utilisateur

CyberData

CyberData 11187 Manuel utilisateur

CyberData

CyberData 11187 Manuel

CyberData

CyberData VoIP Zone Controller Manuel

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur