CyberData 011528 Manuel

Installation Method

The site where you install the switch may greatly affect its performance. When installing, please take the following into

consideration:

• Test the PoE network drop before connecting the CyberData device.

• Use caution when inserting or modifying connections and install the product in a clean, flat wall surface.

• Ensure there are no temperature or humidity concerns in the intended environment. See the Specs tab at

https://www.cyberdata.net/products/011528 for the acceptable temperature and humidity operating ranges.

• To prevent electrical issues, avoid installing in close contact with other electrical wires, next to in-wall insulation, or exposing

the circuit board upon completing the installation.

• Never install components in wet locations or during lightning storms.

• It is advised to consult a certified electrician for installation.

Typical Wall Installation

Parts

Plug in the network cable and angle in

2Secure Unit with Faceplate Screws

Fold agnuts down,

then insert into wall cutout and

tighten screws

(1) Low Voltage Bracket

(2) Faceplate Screws

(2) PCBA Mounting Screws

Accessory Kit

(1) PCBA(1) Faceplate

Dimensions

Mount PCBA to Faceplate

Contacting CyberData

2.756 [70]

4.567 [116]

0.177 [4.5] 3.900 [99]

3.270 [83]

DIMENSIONS ARE IN INCHES [MILLIMETER]

Dimensions are in Inches [Millimeters]

2.250 [57.15]

3.875 [98.43]

Dimensions are in Inches [Millimeters]

Faceplate

PCBA

Mounting Screw

Sales: 831-373-2601 ext. 334

Support: 831-373-2601 ext. 333

Support Website: http://support.cyberdata.net/

RMA Department: 831-373-2601 ext. 136

RMA Email: [email protected]

RMA Status: http://support.cyberdata.net/

Warranty Information: http://support.cyberdata.net/

Corporate Headquarters

CyberData Corporation

3 Justin Court

Monterey, CA 93940, USA

Phone: 831-373-2601

Fax: 831-373-4193

http://www.cyberdata.net/

The IP Endpoint Company

Installation Quick Reference

In-Wall 2-Port Gigabit PoE Switch

011528

Wall Cutout

The Standard RJ-45 Introduction

Regarding cable-making methods, a cable that does not meet the standards of the sequence data will make the data transmission

speed slow, unstable, and even be blocked. Ta bl e 1 represents the standard RJ-45 jack and the connector (Figure 1) and pin

definition:

Figure 1. Standard RJ-45 Jack / Connector

The Standard Cable, RJ-45 Pin Assignment

The following figures show a straight cable and a crossover cable connection. Use a straight cable connection to connect switch/

Hub or other devices:

Straight cable for the switch (uplink MDI-II port) to switch/Hub or other devices connection.

Crossover cable for switch (MDI-X port) to switch/hub or other network devices (MDI-X port) connection.

Table 1. RJ-45 Connector Pin Definitions

Pin Number Signal

1 _TX1 +(PoE Power+)

2 _TX1 - (PoE Power+)

3 _RX1 + (PoE Power-)

4_TX2+

5_TX2--

6 _RX1 - (PoE Power-)

7_RX2+

8_RX2-

1 2 3 4 5 6 7 8

Powering on the In-Wall 2-Port Gigabit PoE Switch

Your existing central POE Switch powers the CyberData switch. No additional power supply is required. Plug your cable from your

main PoE switch into the ethernet port of the CyberData switch, which will power on for use.

How the Input Power is Distributed

Typical Installation

LED Status Description

PD (Orange) ON Switch has a connection from the PD port to the PSE device.

Power has been successfully applied.

OFF Connection to the PSE device is not present. No power has been applied to the switch.

PSE (Orange) ON PD device such as IP phone is connected to the port and drawing power.

OFF PD device is not connected or no power is being drawn from the switch.

Link/Act (Green) ON

A valid link

established.

Blink Traffic is present on port.

OFF

link

has been established.

Autres manuels CyberData Changer

CyberData

CyberData 10845 Manuel utilisateur

CyberData

CyberData 11006 Manuel utilisateur

CyberData

CyberData 11187 Manuel utilisateur

CyberData

CyberData 4-Port Powered USB 2.0 Hub 010845 Manuel utilisateur

CyberData

CyberData 011539 Manuel

CyberData

CyberData 011539 Manuel

CyberData

CyberData 4-Port PoweredUSB 2.0 Hub 011006 Manuel utilisateur

CyberData

CyberData 10845 Manuel utilisateur

CyberData

CyberData RS232 Manuel utilisateur

CyberData

CyberData 10776 Manuel utilisateur

CyberData

CyberData 4-Port PoweredUSB 2.0 Hub Manuel utilisateur

CyberData

CyberData IBM SI/O Manuel utilisateur

CyberData

CyberData 11187 Manuel

CyberData

CyberData 10807 Manuel utilisateur

CyberData

CyberData VoIP Zone Controller Manuel

CyberData

CyberData 011508 Manuel

CyberData

CyberData Hub Manuel utilisateur

CyberData

CyberData KS-1000 Manuel utilisateur

CyberData

CyberData 11187 Manuel

CyberData

CyberData 10807 Manuel utilisateur

CyberData

CyberData 10630 Manuel utilisateur

CyberData

CyberData External Hub Manuel utilisateur

CyberData

CyberData 011187 Manuel

CyberData

CyberData 11171 Manuel

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur