Custom Audio Electronics SMICE-PS Manuel utilisateur

SMICE-PS

SMICE

Desktop Thermal Printer

with integrated power supply

112/80 mm

User Manual

www.custom.it

SMICE-PS

form, whether on paper or electronically, is strictly forbidden. While CUSTOM

ENGINEERING SPA guarantees that the information contained in this manual

has been carefully checked and verified, CUSTOM ENGINEERING SPA and

other resources utilized in its creation assume no responsibility for situations

arising from its use.

Feedback regarding any errors in the manual’s content or suggestions on

how it could be improved would be greatly appreciated. Since its products

are subject to continuous checking and improvement, CUSTOM

ENGINEERING SPA reserves the right to modify the information contained

in this manual without prior notice.

COD. DOME - SMICE-PS VERS. 1.00

CUSTOM ENGINEERING SPA

Str. Berettine 2 - 43010 Fontevivo (PARMA) - Italy

Phone. : +39 0521-680111 - Fax : +39 0521-610701

http: www.custom.it http: www.smice.com

To contact our Technical Support :

Phone. : +39 0521-680163 - Fax : +39 0521-680146

Email : [email protected]

SMICE-PS

PRINTER COMPONENTS

A. SMICE-PS - front exterior view

1- Printer base

2- Cover

3- Paper guide

4- Print mechanism + Cutter

5- Backlighting FEED key

6- Key “KEY2”

7- Paper opening

8- Paper control edges for 80mm roll

9- Plate

SMICE-PS

B. SMICE-PS - rear view

1- Interface connector

2- Drawer connector

3- Power supply connector

4- ON/OFF switch

TABLE OF CONTENTS

SMICE-PSiPS

INTRODUCTION

MANUAL ORGANIZATION ............................................................................1

SYMBOLS USED IN THE MANUAL...............................................................1

GENERAL SAFETY INFORMATION.............................................................1

UNPACKING THE PRINTER .........................................................................2

MAIN CHARACTERISTICS...........................................................................3

PRINTER DESCRIPTION .............................................................................4

1. INSTALLATION AND OPERATION

1.1 CONNECTIONS................................................................................... 1-1

1.1.1 Power supply ................................................................................. 1-1

1.1.2 Connectors for Drawers 1 and 2.................................................... 1-2

1.2 SETUP.................................................................................................. 1-3

1.3 HEXADECIMAL DUMP ........................................................................ 1-5

1.4 MAINTENANCE.................................................................................... 1-5

1.4.1 Changing the paper roll.................................................................. 1-5

1.4.2 Cleaning ......................................................................................... 1-7

2. INTERFACES

2.1 SERIAL - RS232 / TTL ........................................................................ 2-1

2.2 SERIAL - RS422 .................................................................................. 2-3

2.3 SERIAL - RS485 .................................................................................. 2-4

2.4 PARALLEL - CENTRONICS................................................................ 2-5

2.5 OFF LINE ............................................................................................. 2-6

3. PRINTER FUNCTIONS

3.1 COMMAND DESCRIPTIONS .............................................................. 3-1

3.1.1 ESC/POS Emulation..................................................................... 3-1

4. TECHNICAL DATA

4.1 TECHNICAL DATA............................................................................... 4-1

4.2 DIMENSIONS....................................................................................... 4-3

TABLE OF CONTENTS

SMICE-PS ii

5. CHARACTER SETS

5.1 CHARACTER SETS ............................................................................ 5-1

APPENDIX A. MISCELLANEOUS NOTES

A.1 TICKET ALIGNMENT.......................................................................... A-1

A.1.1 Ticket alignment............................................................................. A-1

A.1.2 Alignment sensor calibration ......................................................... A-1

INTRODUCTION

SMICE-PS

MANUAL ORGANIZATION

In addition to the Introduction which contains information regarding the

symbols used in the manual, general safety information, instructions for

unpacking the printer and a brief description and main characteristics of the

machine, this manual is divided into the following chapters:

Chapter 1: Contains the information required for correct printer installation

and use

Chapter 2: Contains interface data

Chapter 3: Contains a description of printer controls

Chapter 4: Contains printer technical data

Chapter 5: Contains the character sets (fonts) used by the printer

SYMBOLS USED IN THE MANUAL

NOTE

Gives important information or suggestions for printer use.

WARNING

Information indicated by this symbol must be followed carefully to

avoid damaging the printer.

DANGER

Information indicated by this symbol must be followed carefully to

avoid damage or operator injury.

GENERAL SAFETY INFORMATION

•Read and retain the instructions which follow.

•Follow all indications and instructions given on the printer.

•Before cleaning the printer, be sure to pull out the electrical cable.

•Use a damp cloth to clean the printer. Do not use liquid or spray products.

•Do not operate the printer near water.

•Make sure that the surface on which the printer rests is stable. If it is not,

the printer could fall, seriously damaging it.

INTRODUCTION

SMICE-PS 2

•Make sure that the printer rests on a hard (non-padded) surface and that

there is sufficient ventilation.

•When positioning the printer, make sure its cables will not be damaged.

•Use the type of electrical power supply indicated on the printer label. If

uncertain, contact your dealer.

•Make sure the electrical system that supplies power to the printer is

equipped with a ground wire and is protected by a differential switch.

•If power is supplied to the printer using an extension cord, make sure

that the total electrical input of the connected devices does not exceed

the maximum current permitted by the type of extension in use or, in any

case, a maximum of 15A.

•Do not block the ventilation openings.

•Do not insert objects inside the printer as this could cause short-circuiting

or damage components that could jeopardize printer functioning.

•Do not spill liquids onto the machine.

•Do not carry out repairs on the machine yourself, except for the normal

maintenance operations given in the user manual.

•Make sure that there is an easily-accessible outlet with a capacity of no

less than 15A in the vicinity of where the printer is to be installed.

•Unplug the printer from the electrical mains and call a specialized

repairman if any of the following conditions should arise:

A. the power supply connector is damaged

B. liquid has spilled into the printer

C. the printer has been exposed to rain or water

D. the printer is not functioning normally despite the fact that all

instructions given in the user manual have been followed

E. the printer has been dropped and the cover is damaged

F. printer performance is noticeably reduced

G. the printer is not working

•Periodically perform scheduled maintenance on the printer to avoid dirt

build-up that could compromise the correct, safe operation of the unit.

UNPACKING THE PRINTER

Remove the printer from the carton, taking care not to damage the packing

materials which should be retained for future shipping/moving.

Make sure all components listed below are present and not damaged. If any

part is missing and/or damaged, contact customer service.

INTRODUCTION

SMICE-PS

1. Upper tray

2. Manual (or CD-rom)

3. Upper packing frame

4. Printer

5. Paper roll

6. Lower packing frame

7. Lower tray

8. Carton

9. Power supply cable

•Open the printer packaging

•Remove the protective tray

•Lift off the upper packing frame and remove the manual (or CD-rom)

•Lift out the printer and remove it from the plastic bag

•Store the carton, trays and other packing materials for future shipping/

moving

MAIN CHARACTERISTICS

It is a practical, easy-to-use, tabletop printer.

It offers an excellent solution for all industrial, professional and laboratory

applications that require immediate data printout onto a receipt: POS,

weighing systems, cashier systems, bookkeeping, receipts or fiscal

(Fig.1)

INTRODUCTION

SMICE-PS 4

documents, security, checking and diagnosis.

It is equipped with a 200 dpi (8 dots/mm) thermal printing mechanism that

utilizes 112mm-wide paper rolls. In addition to normal printing features, the

printer includes a wide range of added functions:

• High-speed printing: 85 mm/sec (normal), 100 mm/sec. (High speed).

• Easy paper changing (automatic paper loading)

• ESC/POS emulation

• Paper width : 112/80 mm.

• Bar code UPC-A, UPC-E, EAN13, EAN8, CODE39, ITF, CODABAR,

CODE93, CODE128 and CODE32

• 3 standard and international character fonts

• Programmable fonts

• Widht and height characters setting from 1 to 8, boldtype, italic,

underlined, rotated 90°/180°

• Possibility to define function macros for automatic operation repetition

• Graphic printing

• Printing density (from -50% to +150%)

• 1 programmable logo (832 x 630 dots).

• Serial interfaces ( from 1200 to 115200 bps) : RS232, RS422, RS485,

TTL.

• Alternatives interfaces : CENTRONICS.

• Reception buffer : from 16 bytes to 8 Kbytes.

PRINTER DESCRIPTION

The printer (fig.2) consists of a shell in ABS-V0 (1) equipped with a cover (2)

that provides access to the paper roll and printing mechanism.

On the front are the backlighting FEED key (3); the “KEY2” key is located

inside of the printer by side of the roll holder opening (4).

Table des matières

Autres manuels Custom Audio Electronics Imprimante

Custom Audio Electronics

Custom Audio Electronics MT2480 Manuel utilisateur

Custom Audio Electronics

Custom Audio Electronics TG02H Instructions d'installation

Custom Audio Electronics

Custom Audio Electronics VKP80III Manuel utilisateur

Custom Audio Electronics

Custom Audio Electronics TK300II Manuel d'installation

Custom Audio Electronics

Custom Audio Electronics BIGII Touch PC Manuel utilisateur

Custom Audio Electronics

Custom Audio Electronics TPT60H Manuel utilisateur

Custom Audio Electronics

Custom Audio Electronics KPM180H Manuel utilisateur

Custom Audio Electronics

Custom Audio Electronics MY3 X Manuel utilisateur

Custom Audio Electronics

Custom Audio Electronics TPTCM60III Manuel utilisateur

Custom Audio Electronics

Custom Audio Electronics DP24-40 H Manuel utilisateur

Custom Audio Electronics

Custom Audio Electronics TL60III Manuel utilisateur

Custom Audio Electronics

Custom Audio Electronics Custom Manuel utilisateur

Custom Audio Electronics

Custom Audio Electronics KPM202 Manuel utilisateur

Custom Audio Electronics

Custom Audio Electronics TG2460H Manuel utilisateur

Custom Audio Electronics

Custom Audio Electronics DP24-42BA Manuel utilisateur

Custom Audio Electronics

Custom Audio Electronics PLUS4 Manuel utilisateur

Custom Audio Electronics

Custom Audio Electronics TPT 60 Manuel utilisateur

Custom Audio Electronics

Custom Audio Electronics s'print DPT100-B Manuel utilisateur

Custom Audio Electronics

Custom Audio Electronics PD190 Manuel utilisateur

Custom Audio Electronics

Custom Audio Electronics D4 102 Manuel d'instructions

Custom Audio Electronics

Custom Audio Electronics TFTCM112II Manuel utilisateur

Custom Audio Electronics

Custom Audio Electronics Lola-lp2 Manuel utilisateur

Custom Audio Electronics

Custom Audio Electronics TK303 Manuel utilisateur

Custom Audio Electronics

Custom Audio Electronics TK302 Supplément

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Canon

Canon i70 Series Manuel utilisateur

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Canon

Canon LASER SHOT LBP-1210 Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Canon

Canon PIXMA PRO-1 Series Manuel utilisateur

Canon

Canon PIXMA G3560 Guide de configuration

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Epson

Epson ET-7750 Mode d'emploi

Canon

Canon CLBR 460ps Manuel utilisateur

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Epson

Epson SC-F7100 series Manuel utilisateur

Epson

Epson Stylus C40UX Manuel utilisateur

Canon

Canon imagePASS-A2 Manuel utilisateur

Canon

Canon S820D Manuel utilisateur