Cornelius SPIRE 4.2 Guide de sécurité
Manual Installation Conversion Kit 4.1 To 4.2
©2019, Cornelius Inc. - 1 - Publication Number: 629097805INS
MANUAL INSTALLATION CONVERSION KIT
SPIRE 4.1 TO 4.2
SAFETY OVERVIEW
• Read and follow ALL SAFETY INSTRUCTIONS in this manual and any warning/caution labels on the unit
(decals, labels or laminated cards).
• Read and understand ALL applicable OSHA (Occupational Safety and Health Administration) safety regula-
tions before operating this unit.
SAFETY ALERT SYMBOL
Types of Alerts
SAFETY TIPS
• Carefully read and follow all safety messages in this manual and safety signs on the unit.
• Keep safety signs in good condition and replace missing or damaged items.
• Learn how to operate the unit and how to use the controls.
• Do not let anyone operate the unit without proper training. This appliance is not intended for use by very
young children or infirm persons without supervision. Young children should be supervised to ensure that
they do not play with the appliance.
• Keep your unit in proper working condition and do not allow unauthorized modifications to the unit.
Safety Instructions
!
WARNING:
Before starting installation, read and understand all safety label and warnings on the machine. Also review and
understand all safety instructions in the owners, installation and service manuals.
Failure to comply could result in serious injury, death or damage to the equipment.
This is the safety alert symbol. When you see this in the manual or on the unit, be alert to the
potential of personal injury or damage to the unit.
!
DANGER:
Indicates an immediate hazardous situation which if not avoided WILL result in serious
injury, death or equipment damage.
!
WARNING:
Indicates a potentially hazardous situation which, if not avoided, COULD result in serious
injury, death, or equipment damage.
CAUTION:
!
Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or
moderate injury or equipment damage.
!
Revision Date: June 7, 2019 www.cornelius.com Revision: B
Manual Installation Conversion Kit 4.1 To 4.2
Publication Number: 629097805INS - 2 - ©2019, Cornelius Inc.
QUALIFIED SERVICE PERSONNEL
!
WARNING:
Only trained and certified electrical, plumbing and refrigeration technicians should service this unit.
All wiring and plumbing must conform to national and local codes. Failure to comply could result in serious injury,
death or equipment damage.
SAFETY PRECAUTIONS
!
WARNING:
Disconnect power to the unit before servicing. Follow all lock out/tag out procedures established by the user. Verify all
power is off to the unit before performing any work. Failure to comply could result in serious injury, death or damage to
the equipment.
CAUTION:
!
Always be sure to keep the area around the unit clean and free of clutter. Failure to keep this area clean may result in
injury or equipment damage.
CAUTION:
!
Note the following: This unit is not designed for use in outdoor locations. The appliance must be placed in a horizontal
position. The appliance is not suitable for installation in an area where a water jet would be used.
Manual Installation Conversion Kit 4.1 To 4.2
©2019, Cornelius Inc. - 3 - Publication Number: 629097805INS
MANUAL INSTALLATION CONVERSION KIT SPIRE 4.1 TO 4.2
INSTALL KIT PART LIST:
TOOLS REQUIRED:
INSTALLATION INSTRUCTION:
1. Shut Down unit per proper shutdown procedure
2. Unplug unit from its AC Power source.
PART NUMBER DESCRIPTION QTY
620070411 Ebox cover (pre-assembled with all required labels and
new wiring diagram) 1
620070273 Door service cover pre-assembled w/ mounting screws
and labels) 1
N/A AIO Display assembly (pre-assembled with bezel and
mounting bracket and screws) 1
N/A LX3 mounting bracket assembly (pre-assembled w/LX3,
terminal block, display on/ off switch and required wiring/
jumpers)
1
62058545-002 Breaker Circuit 5A 1
620058733-003 Ferrite Snap- On 240 Ohm 1
620058733-007 Ferrite Snap- On 225 Ohm 1
620070445 Flex Antenna Kit 2
620070523-200 MFV Board Assy 1
620070550 Bracket 3rd Circuit Breaker 1
620070556 Cable Clamp 2
629097805 Installation Instructions 1
Description
#2 Phillips Screwdriver
Utility Knife or side-cutting pliers
Flat Head Screwdriver
11/32” nut driver or equivalent
!
WARNING
Only trained and certified electrical, plumbing and refrigeration technicians should
service this unit.
All wiring and plumbing must conform to National and Local Codes. Failure to
comply could result in serious injury, death or equipment damage.
Manual Installation Conversion Kit 4.1 To 4.2
Publication Number: 629097805INS - 4 - ©2019, Cornelius Inc.
3. Locate power cord inside unit next to the valves and add ferrite supplied on the power cord at approximate
location shown.
Figure 1
4. Open door and remove translucent door service panel and discard of properly.
Figure 2
Manual Installation Conversion Kit 4.1 To 4.2
©2019, Cornelius Inc. - 5 - Publication Number: 629097805INS
5. Unplug all connections to display, this includes the cove lighting to the LX3 board.
Figure 3
6. Remove ebox cover saving the (2) screws. Discard ebox cover.
7. Unplug all cables/harnesses from MFV board, remove and properly discard MFV board, install new MFV board supplied
with the kit and reinstall previously removed cables/harnesses.
8. Remove wire bundle from the (2) most far right wire clips.
Figure 4
9. From the same wire bundle, remove the (2) USB cables that feed the MFV board, USB hub and the (1) antenna cable that
goes to the rear of the unit.
10. Carefully remove/clip off the (2) far most right wire clips from step 8 and discard.
11. Insert circuit breaker into the mounting bracket supplied.
cove lighting harness
Manual Installation Conversion Kit 4.1 To 4.2
Publication Number: 629097805INS - 6 - ©2019, Cornelius Inc.
12. Insert new circuit breaker bracket into the(2) holes where the wire clips used to be. Use (2) #8-32 nuts to secure the
bracket to the unit. (DO NOT OVERTIGHTEN)
Figure 5
13. Install (2) new cable clip supplied with kit to the mounting studs of the circuits breaker with (1) #8-32 nut on each stud as
shown. (DO NOT OVERTIGHTEN)
Figure 6
Manual Installation Conversion Kit 4.1 To 4.2
©2019, Cornelius Inc. - 7 - Publication Number: 629097805INS
14. Wire new circuit breaker with supplied harness, one end goes to the 12VDC Power supply (red to V+, black to V-)....the
other gets routed to the door with the (2) USB Cables and (1) antenna cable. Refer to new wiring diagram supplied with
kit for reference.
15. Bundle wires thru wire clips shown on step 11 except the (2) USB cables, (1) antenna cable and display/cove lighting
harnesses.
16. Using the supplied wire ties, secure the (2) USB cables, (1) antenna cable and display/cove lighting harnesses from the
main wire bundle downward approx. 1.5'' to 2''. Make sure all wires/cables are cleanly bundled and secured.
Figure 9
Figure 7 Figure 8
1.5''-2.0''
Manual Installation Conversion Kit 4.1 To 4.2
Publication Number: 629097805INS - 8 - ©2019, Cornelius Inc.
17. Remove the NUC mounting panel assembly from the door by loosen the (2) top screws and removing the (2) bottom
screws, discard bottom screws. Lift the panel assembly up and out, this panel assembly can be discarded. Remove the (2)
top screws and save.
Figure 10
18. Remove the display assembly from the door by loosening the ‘A’ screws and removing and saving the ‘B’ screws.
Figure 11
19. Carefully lift up and out the display assembly from the door. Place display assembly on a protected table top, glass side
down to get ready to remove lens/lighting.
B
B
A
A
A
A
B
B
Manual Installation Conversion Kit 4.1 To 4.2
©2019, Cornelius Inc. - 9 - Publication Number: 629097805INS
20. Remove and save the (6) ‘C’ screws, lift up the lens / lighting and place aside and then remove the (3) white reflectors.
The old display can now be disposed of per local, state or national recycling laws for electronic equipment.
21. Reassemble the reflectors and lens / lighting into the new display assembly supplied in the kit. Do not overtighten the
screws that mount the lens / lighting, these should be hand tight only. Make sure the lighting harness is routed thru
the lens opening as shown below.
Figure 14
Figure 12 Figure 13
C
C
C
C
C
C
Manual Installation Conversion Kit 4.1 To 4.2
Publication Number: 629097805INS - 10 - ©2019, Cornelius Inc.
22. Mount new display assembly onto door key slots. Reinstall ‘B’ screws from step 18. Tighten all (8) screws hand tight only.
(DO NOT OVERTIGHTEN)
23. Clean back of door with mild detergent or alcohol wipe to prepare the surface for the adhesive tape. Remove tape backing
from new LX3 mounting bracket (backside of bracket) and install bracket using (2) screws from step 17. Firmly push
bracket, where tape is located, into door for best tape adhesion.
Figure 15
24. Install the display power harness from ebox at ‘Z’ and the cove lighting harness from the 3rd circuit breaker at ‘Y’ onto the
terminal block. Note the wire colors and their locations installed on the terminal block.
Figure 16
Tape location
underneath
bracket
screw
Clean back
of door
Y
Z
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Cornelius Distributeur
Cornelius
Cornelius QUEST ELITE 2 FLAVOR Manuel utilisateur
Cornelius
Cornelius IDC 255 PROGATE DRIVE THRU UNIT Manuel utilisateur
Cornelius
Cornelius Ribbon Manuel utilisateur
Cornelius
Cornelius ABS 2.0 Manuel utilisateur
Cornelius
Cornelius Vitalize430 Manuel de l'opérateur
Cornelius
Cornelius 318569000 Manuel utilisateur
Cornelius
Cornelius VIPER (E) 2 FLAVOR Manuel utilisateur
Cornelius
Cornelius Jetspray JT20 Manuel utilisateur
Cornelius
Cornelius REMCOR 1550 Guide de configuration
Cornelius
Cornelius SUBWAY PEPSI SPIRE 3.0 Guide de configuration
Cornelius
Cornelius IDC 255 PROGATE DRIVE THRU UNIT Manuel utilisateur
Cornelius
Cornelius AquaCare Manuel utilisateur
Cornelius
Cornelius IDC Pro Mode d’emploi
Cornelius
Cornelius VIPER 3 FLAVOR Manuel utilisateur
Cornelius
Cornelius ED 300 BC Manuel utilisateur
Cornelius
Cornelius IDC PRO 255 Manuel utilisateur
Cornelius
Cornelius VANTAGE Manuel utilisateur
Cornelius
Cornelius IDC PRO 255 Manuel utilisateur
Cornelius
Cornelius Enduro 200 Manuel utilisateur
Cornelius
Cornelius IDC Pro255 Manuel utilisateur
