Cooper Scantronic 8750 Manuel utilisateur

Installation Guide

8750

Ethernet Module

8750

Introduction

Overview

The 8750 is a plug-in module for the 7510r and i-on40

control units that allows them to communicate over the

Internet using an Ethernet connection to a local switch or

router.

The module must be fitted within the body of the control unit,

which has sockets for that purpose. This manual provides

brief instructions on fitting the 8750. To program the control

unit to use the 8750 please see “7510r Installation and

Programming Guide” or the “i-on40 Programming Reference

Guide”.

Installation

Caution: If you are adding the 8750 to a control unit that

has already been installed then first make sure that the

system is completely unset and in installer programming

mode. (This is to prevent the control unit raising un-

necessary tamper alarms when you open the case.)

Fitting The Module To A 7510r

1. Remove mains power from the 7510r.

2. Undo the two screws at the bottom of the case.

Figure 1. Screw Locations

3. Ease the case body from the wall plate.

Caution! Disconnect the ribbon cable from the wall plate

before opening the case completely (see Figure 2).

8750

Figure 2. Internal Ribbon Cable

4. Undo all four screws holding the body of control unit

together (see Figure 3).

5. Disconnect the speaker and battery connectors.

1. Screw positions 2. Battery and Speaker Connectors

Figure 3. Screw Positions

6. Partially lift the back of the case up and disconnect the

siren lead before completely removing the back of the

case. Figure 4 shows the layout of the main printed

circuit board (PCB).

8750

110

1 Sockets for module 6 Kick Start jumper

2 USB connector 7 Reset codes jumper

3 Siren connector 8 Battery connector

4 Tamper switch 9 Speaker connector

5 Microphone 10 Tag reader

Figure 4. Main Printed Circuit Board.

7. Unpack the 8750 and fit the module to the sockets on the

control unit PCB (see Figure 5).

Figure 5. Fit 8750 Module

8. Present the back of the case to the case front and re-

connect the siren, battery and speaker (see Figure 4).

9. Seat the back of the case into the case front. Refit all four

screws holding the case together (see Figure 3).

10. Run the Ethernet cable from its access point to the 7510r

wall plate. Select a suitable cable entry in the wall plate

and feed the RJ45 connector through.

11. Fit the RJ45 connector into the socket on the edge of the

module (see Figure 6).

8750

Figure 6. Connect Ethernet Lead.

12. Present the case to the wall plate and re-connect the

ribbon cable (see Figure 7).

Figure 7. Connect Ribbon Cable

13. Fit the case to the wall plate and refit the securing screws

(see Figure 1).

14. See “Checking That The Module Works” on page 7.

8750

Fitting The Module To An i–on40

1. Remove mains power.

2. Open the control unit (see Figure 8 ).

Figure 8. Opening the i-on40 Control Unit.

3. Disconnect the battery.

4. Feed the end of the Ethernet cable in from the outside of

the case through one of the cable entry holes. Do not use

the mains cable entry hole.

5. Connect the Ethernet cable to the RJ45 socket on the

module (see Figure 9).

Figure 9. Connect Antenna Cable

8750

6. Fit the 8750 to the plug on module sockets (see Figure 10).

Take care not to unseat the Ethernet lead connector. Do not

use excessive force when seating the module.

Figure 10. Fitting 8750 Module

7. Re-connect the battery. (The control unit will not start.)

8. Re-fit the control unit lid.

Programming

Checking that the Module Works

Apply power to the control unit.

Enter the User programming menu.

Select System Config – About Comms.

After short delay the display shows:

IP Address: The IP address currently being used by the

control unit. The address will be 000.000.000.000 if you

have not programmed an IP address, or if you wish to use

DHCP but the control unit cannot detect a DHCP server.

IP Subnet: The subnet mask programmed into the control

unit.

IP Gateway: The IP address of the gateway you have

programmed in.

MAC Number: The Media Access Control number of the

Ethernet module you have fitted.

8750

To complete programming the control unit please see either

“7510r Installation and Programming Guide” or “i-on40

Programming Guide” depending on the control unit.

Set Up the IP Address of the ARC

ARCs can use two types of receiver for alarm messages over

IP: an IRIS polling engine, or a specialised application

running on a PC. If the ARC employs an IRIS polling engine

then this works on a separate IP address to the PC used to

receive alarm reports and you must remember to store the

polling engine’s IP address.

When communicating with the alarm message receiver at the

ARC you can specify two IP addresses. The control unit sends

data to the second ARC IP address if a call to the first ARC IP

address fails (and you have selected Alternate in Reporting,

Alarms, Call Mode.)

In addition, you must store a string of characters that the

receivers use to identify every individual control unit. This

identifier is independent of the ARC account numbers.

To set up the IP address of the ARC:

On the 7510r select Reporting - Alarms - IP Network.

On the i-on40 select Communications - ARC Reporting - IP

Network.

The display shows the following options:

Unit name Select this option and key in a string of up to

32 characters. This string must be unique for

each control unit communicating to a receiver.

Polling Eng IP Address

Key in the IP address of the IRIS polling

engine.

ARC IP Address 1

Key in the ARC’s main IP address.

Note that this option also allows you to key in a

unique identifying name for the ARC.

ARC IP Address 2

Key in the ARC’s alternate IP address.

This option also allows you to key in a unique

identifying name for the ARC.

8750

Note: On the i-on40 ARC IP Addresses 1 and 2 both appear

under a single menu item “ARC IP Address”.

Setting up for Downloader

While connected Downloader can inspect and/or change the

control unit’s programming configuration. If you do not wish

to change the configuration you can simply monitor the state

of the control unit and its zones from the PC.

To use Downloader software over an IP connection you must

store two IP addresses that the control unit can “call” in order

to start a Downloading session. The user starts the call by

selecting one of the IP address.

To program the Downloader IP address:

On the 7510r select Downloading - IP Network.

On the i-on40 select: Communications - Downloading - IP

Network.

The options available are:

IP Address 1 Key in the IP Address used by Downloader.

IP Port 1 Key in the port number that Downloader

“listens” to on the remote PC at IP address 1.

IP Address 2 Key in an alternate IP Address used by

Downloader.

IP Port 2 Key in the port number used by the alternate IP

address.

Note: On the i-on40 both IP Addresses are under a single

menu and both IP Ports are under a single menu.

8750

NOTES:

Table des matières

Autres manuels Cooper Unité de contrôle

Cooper

Cooper Scantronic 8844 Manuel utilisateur

Cooper

Cooper Crouse-Hinds IF 1589 Guide de configuration

Cooper

Cooper 9930 Manuel utilisateur

Cooper

Cooper S280-79-10 Manuel utilisateur

Cooper

Cooper F6-PA-LS Manuel utilisateur

Cooper

Cooper Z-WAVE RF232 Manuel utilisateur

Cooper

Cooper Scantronic 95 Manuel utilisateur

Cooper

Cooper Scantronic 9 5 Series Mode d'emploi

Cooper

Cooper Scantronic 65 Manuel utilisateur

Cooper

Cooper CEAG Webmodule ZB-S Manuel utilisateur

Cooper

Cooper Scantronic 9 5 Series Manuel utilisateur

Cooper

Cooper Scantronic 770r Manuel utilisateur

Cooper

Cooper LCMD-10 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur