Code Alarm CATX120 Mode d'emploi

Model CATX120

Programming Guide

The keychain transmitters included with the system have

been pre-programmed at the factory, with each button pre-

assigned to control a specific function of the system.

It is important to remember that during programming, each

individual step of the procedure must be executed within 15

seconds of the previous step.

When the 15 second time limit is allowed to expire, the

system will automatically terminate the programming mode.

This is indicated by a long chirp from the siren.

Additionally, the system will store codes from up to 4

different transmitters. If a 5th transmitter is programmed to

any receiver channel, then the first transmitterprogrammed

to that channel will be erased from the system’s memory.

To program new or additional transmitters, the alarm must

be disarmed and the valet switch must be in the OFF

position:

1. Enter the vehicle, and turn the ignition key to the ON

position.

2. Press and release the valet/programming/override

switch 3 times.

3. The dash LED will flash one time, and the sounding

device will beep one time, indication the system is ready to

accept programming for transmitter 1.

4. Press and hold the Arm Icon button until the sounding

device emits a long beep, indicating the signal has been

stored into memory.

5. If you have additional transmitters (up to 4) that need to

be programmed, repeat step 4 for each transmitter.

Changing the Remote Control Battery

The 12-volt alkaline battery supplied in your remote

transmitter should last approximately one year, depending on

usage. When the battery begins to weaken, you will notice a

decrease in range, or the distance from your vehicle that

your remote transmitter will operate. Follow the instructions

below to change the remote transmitter battery.

For Customer Service and Product information Call

1-800-421-3209

1. Insert the edge of a coin into the slot at the side of the

remote control. Twist the coin to pry the remote control

halves apart.

2. Remove the old battery and replace with a new one. Be

sure to observe the (+) and (-) signs in the battery

compartment.

3. Carefully snap the case halves back together, then test

the remote control.

Model CATX120

Programming Guide

Table des matières

Autres manuels Code Alarm Alarme de voiture

Code Alarm

Code Alarm CA-640 Manuel utilisateur

Code Alarm

Code Alarm CA100 Manuel utilisateur

Code Alarm

Code Alarm Professional Series CA 1050 Manuel utilisateur

Code Alarm

Code Alarm CA-160 Manuel utilisateur

Code Alarm

Code Alarm CA-130 Manuel utilisateur

Code Alarm

Code Alarm F20 Manuel utilisateur

Code Alarm

Code Alarm CA-130 Manuel utilisateur

Code Alarm

Code Alarm CA 671 Manuel utilisateur

Code Alarm

Code Alarm CA 420A Manuel utilisateur

Code Alarm

Code Alarm CA 1550 Manuel utilisateur

Code Alarm

Code Alarm CA 420 Manuel utilisateur

Code Alarm

Code Alarm UTXPR Manuel du propriétaire

Code Alarm

Code Alarm PROFESSIONAL CA 1045 Manuel utilisateur

Code Alarm

Code Alarm CA611 Manuel utilisateur

Code Alarm

Code Alarm CA-140 Manuel utilisateur

Code Alarm

Code Alarm CA 6551 SST Manuel utilisateur

Code Alarm

Code Alarm 420A Manuel utilisateur

Code Alarm

Code Alarm Professional ca6153 Manuel utilisateur

Code Alarm

Code Alarm ca 1051 Manuel utilisateur

Code Alarm

Code Alarm CATX610 Mode d'emploi

Code Alarm

Code Alarm PROFESSIONAL SERIES Manuel utilisateur

Code Alarm

Code Alarm PROFESSIONAL SERIES Manuel utilisateur

Code Alarm

Code Alarm Ca 1053 Manuel utilisateur

Code Alarm

Code Alarm CA-500 Manuel utilisateur

Manuels Alarme de voiture populaires d'autres marques

Clifford

Clifford 3606X Manuel utilisateur

Ultra Start

Ultra Start 2500M SERIES Manuel utilisateur

Ultra Start

Ultra Start 650 Series Manuel utilisateur

Audiovox

Audiovox Prestige Platinum+ APS-511C Manuel utilisateur

Sparkrite

Sparkrite SRA8 Manuel utilisateur

Viper

Viper 4708V Manuel utilisateur

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Manuel

Falcon

Falcon Predator XL3 Guide de l'utilisateur

Audiovox

Audiovox Auto Security XR91 Mode d'emploi

Clifford

Clifford Sabre II Manuel utilisateur

CrimeStopper

CrimeStopper CS-8717 Guide de démarrage rapide

Ultra Start

Ultra Start 450 SERIES Manuel utilisateur

Scytek electronic

Scytek electronic Vectra X3 Manuel utilisateur

Excalibur

Excalibur AL-1860-EDPB Manuel utilisateur

Clifford

Clifford CYBER 2 Manuel utilisateur

Gemini

Gemini 7057 Manuel utilisateur

FlashLogic

FlashLogic FLRSBA PRESTIGE Manuel utilisateur

Magicar

Magicar FAI-440 Manuel utilisateur