Clevertronics LP Argonaut PLUS Instructions d'installation et d'utilisation

1948874

V1.6

14 June 2022

Instruction Sheet Template - V1.3 –Updated 20/01/2022

Clevertest and Clevertest Plus

Refer to the supplementary operation guide supplied with the Product.

4HR: CTP will only test for the 2 hours (first test) and 90 minutes duration. 4 hours testing would only be

facilitated as a Manual Discharge Test.

Zoneworks, HIVE (HV/HVG) and DATA Monitored Options

Fittings with part numbers -ZW, -HV, -HVG, -DATA are fitted with Zoneworks communications modules

(nodes). These fittings are monitored using either Powerline Carrier Technology that utilize the power

cable to provide data communication, RF transceiver modules operating in the ISM band or a dedicated

data cable to/from data routers installed on a dedicated data trunk connected to a central Server (can also

be connected via Ethernet/Internet/Fibre). Zoneworks software on the server is used to monitor,

coordinate testing and collate test data from each fitting. Zoneworks Fittings can be commissioned by a

single push of the test switch or by scanning the supplied barcode. The LED Test Switch indicator provides

a multifunction indication of the status of the fitting during testing and normal operation:

Option

State

LED Operation

ZW, DATA,

HVG, HV

Commissioned

LED on Solid (Green)

ZW, DATA

Un-commissioned

Batt plugged-in: yellow 1s, green 1s

Batt unplugged: red 1s, off 1s

HV, HVG

Un-commissioned

With network connectivity

Batt plugged-in: yellow 1s, green 1s

Batt unplugged: red 1s, off 1s

HV, HVG

Un-commissioned

Without network connectivity

Batt plugged-in: yellow 250mS, green 250mS,

yellow 250mS, green 250mS, green 1s

Batt unplugged: red 250mS, off 250mS, red

250mS,off 250mS, off 1s

ZW, DATA

Emergency Light Test In Progress

LED flashes at yellow 5s , 0ff 1s

HV, HVG

Emergency Light Test In Progress

LED flashes at yellow 1s , 0ff 1s

In the case of the DATA version a 2-way “figure 8” cable and terminal block facilitates the connection to

the DATA network via a multi-drop bus (daisy chain connection). For further information of installation of

a Zoneworks system, please refer to the Zoneworks Users Guide and Commissioning Guide (incl. DATA

version)

DALI EM Option

Luminaires with part numbers having -DALI are fitted with DALI modules (nodes) that facilitate connection

and integration to 3rd Party Lighting Control Systems. Before installing the -DALI luminaire, please confirm

that the Lighting Control System has the capability to monitor DALI Emergency Luminaires. The -DALI

fitting will be addressed and configured into the control system by the Lighting Control System

Commissioning Technicians and not Clevertronics.

State

LED Operation

Commissioned/ Un-commissioned

LED on Solid (Green)

Emergency Light Test in progress

LED flashes at 1s On (Yellow) & 1s Off

“IDENTIFY COMMAND”

Lamp and Status LED Flash for 30 seconds

A 2-way “figure 8” cable and terminal block facilitates the connection to the DALI network. DALI

connections are marked as Da Da.

Caution:

On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during

construction. As a result, any Exit & Emergency Units, on these circuits, will have their batteries

discharged or “cycled”. The battery in this fitting has been selected to give excellent long-life

performance in a controlled AS2293 testing environment. Excessive battery cycling will reduce through-

life performance and may lead to premature battery failure. Battery warranty claims, as a result of such

abuse, are specifically EXCLUDED from Clevertronics warranty terms.

Argonaut PLUS Weatherproof Emergency LED Batten

Installation & Maintenance Instruction Leaflet

Victoria (Head Office & Manufacturing)

Website: www.clevertronics.com.au

Email: info@clevertronics.com.au

Phone: +61 3 9559 2700

Fax: +61 3 9559 2799

New South Wales

Phone: +61 2 8805 6400

Fax: +61 2 8805 6444

Queensland

Phone: +61 7 3442 9700

Fax: +61 7 3442 9777

South Australia/Northern Territory

Phone: +61 8 8301 8800

Fax: +61 8 8351 8286

Western Australia

Phone: +61 8 9207 0000

Fax: +61 8 9207 0088

New Zealand

Phone: +64 800 548 448

Designed in Australia to comply with the

requirements of AS2293.3: 2018, AS CISPR15:

2017

Models:

ARGOPLUS-1200-xx-yy-zz-uu

Testing:

Options:

Manual Test

zz = Blank

Microwave Sensor (HI/LO)

xx = SEN

DALI Registered

zz = DALI

DALI Driver

xx = DD

Zoneworks

zz = ZW

Integrated Battery (non-POD)

yy = LP

Zoneworks HIVE

zz = HV/HVG

Emergency POD

yy = LPPOD

4 Hours run time

uu = 4HR

(NOTE: -CT Products supplied with the Clevertest Plus Symbol are activated with Clevertest PLUS

capability. Please refer to the operation guide supplied with the product for details).

Spare Parts:

1550050

Replacement Battery (POD only)

1550230

Replacement Battery (Non-POD only)

8003110

Replacement Emergency LED Board

8002752

Replacement 240V LED Strip

AUM02370050001

Replacement Emergency Driver

AUM02870450001

Replacement Emergency Driver (-SEN, -HV only)

AUM02970010001

Replacement Emergency Driver (-HVG)

AUM02870060001

Replacement Emergency Driver (-HV, -4HR)

1330092

Replacement 240V Driver

1330093

Replacement 240V Driver (-SEN)

1330151

Replacement 240V Driver (-DD)

Important:

It is illegal for anyone, exceptfor a licensed electrician toinstall or maintain this product. Before installation,

ensure that the electricity supply has been switched off and isolated. Installation must be carried out in

accordance with the relevant Australian and International Standards.

Note: This luminaire (with reinforced insulation between control/LED terminal and AC Supply) contains

non-user replaceable light source and battery –to be replaced (if required, refer installation instructions

for battery replacement) by the manufacturer or his service agent or a similar qualified person.

1948874

V1.6

14 June 2022

Instruction Sheet Template - V1.3 –Updated 20/01/2022

Installation:

The product can be mounted/suspended from any solid surface. Follow the below installation steps:

•Determine the installation and power entry method.

•Undo the Diffuser Clips, remove the Diffuser and Gear Tray. Position the batten base in the desired

location and Mark out the fixing points on the mounting surface.

•If the cable entry is to be via the rear of the body –Drill out a suitable entry-hole in the rear of the

batten body (must be suitably sealed after cable entry using a sealant). If the cable entry is via the

end of the batten - Install the provided cable gland, or bring in conduit, to the base as required for

the intended power access.

Note: Only round cables are to be used with the cable gland for an IP65 seal. Keep cable entry

straight and tension free. Ensure all seals are tight.

min. wire diameter 7mm, max. 12mm.

•For surface mounting -, there are 3 extrusions/posts at each end of the base. Drill out the desired

number of fixing points at each end. Fixings must only be through the extrusions/mounting

posts.

oPosition the fitting to the mounting surface and mark the mounting holes.

oCable/Gland entry to be down if mounting vertically.

oDrill the mounting holes.

oFix the base to the surface with appropriate fixings.

oSeal any penetrations/fixing points with appropriate sealant.

•For Surface Mount Clip mounting, measure/mark spacing (see Dimensions image), install

stainless steel clips to surface (use appropriate fixings), then snap batten into clips.

•For Suspension Mounting, measure/mark spacing (see Dimensions image), install suspension

device, E.G chain, and connect chain to batten base.

•Wire mains power cable, 240V 50Hz, to terminals marked Lsw (Switched Active), Lem

(Emergency/Unswitched Active), N & (and DALI Cables to terminals Da Da as applicable)

•Set Colour Switch to the desired colour (3000K / 4000K / 5700K, 4000K set as default)

•Attach Gear Tray to lanyards.

•Re-Install the Diffuser, close all the Diffuser Clips and secure with screws

•The Pod version of the luminaire should be positioned so that prolonged staring into the luminaire

at a distance closer than 330mm is not expected

Wiring:

Sensor Version:

Dimensions:

Driver Setting:. Colour Setting:

For non -SEN/-DD products For -DD products

Recommended currents are 350mA & 650mA for this product. Using settings outside of the recommended will void

warranty.

Battery Replacement (non-POD)

1. Prior to any work, isolate power to any Batten

that requires battery replacement

2. Open the Diffuser by releasing the Batten

Diffuser Clips

3. Remove Gear Tray by unclipping the Gear Tray

Clips on each side (ensure the Gear Tray is

supported while unlocking clips)

4. Remove Battery connector from the Emergency

Driver

5. Remove Battery by removing the

Screw/Washer/Nuts

6. Install replacement Battery/Screw/Washer/Nuts

and connect into Emergency Driver

7. Re-Install the Gear Tray onto the Gear Tray

Clips

8. Re-Install the Diffuser, close all the Diffuser

Clips and secure with screws

NOTE: For POD products refer to Instruction Sheet

for LP POD’s provided with product (1948146)

Testing:

Once connected to the 240V mains supply, the unit must be

allowed to charge the battery for at least 24 hours. Conduct

the following tests:

•For the first test, the emergency lamp must remain

illuminated for at least 2 hours (4 hours for -4HR

fittings), after disconnection from the mains supply.

•Subsequent tests require the unit to illuminate for at

least 90 minutes. The results of all tests are required to

be recorded in a service logbook, which is to be kept on-

site at all times. If the unit fails to remain illuminated for

the requisite time, remedial action must be taken to

repair the situation and once completed, the unit must

pass a subsequent test. For more specific information,

please refer to the current edition of the AS 2293.3

Standard.

•Press and hold Test Button or switch Off Mains Supply,

check that the emergency lamp is On.

•Release the Test Button or Switch On Mains Supply,

check that the emergency lamp is Off (Non-maintained

operation).

Trouble Shooting:

Below are a list of common problems and their possible causes.

Fault: The Green LED Test Switch indicator is not illuminated.

Check: A.C. is connected and is turned on.

Battery is connected

Test Switch for damage.

Fault: Lamp does not illuminate in emergency mode.

Check: A.C. is connected.

Lamp is correctly inserted.

Battery is connected

Fault: Lamp illuminates in emergency mode, but only stays on for a short period.

Check: Battery has been allowed to charge for at least 24 hours.

Battery for damage.

Rated Emergency Lumen Output in accordance with AS2293.1 (refer to spacing tables for

installation positions):

Refer to the Technical Label for classification information.

Warranty:

For Product Warranty information and Terms and Conditions of Sales please refer to our website

http://clevertronics.com.au/terms-conditions-sale-australia-nz/

Ce manuel convient aux modèles suivants

Autres manuels Clevertronics Équipement d'éclairage

Clevertronics

Clevertronics L10 Cleverfit Pro Instructions d'installation et d'utilisation

Clevertronics

Clevertronics Trade Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 LIFELIGHT LLIFE-SM Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 LIFELIGHT LLIFE Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics LED CIRCLITE Instructions d'installation et d'utilisation

Clevertronics

Clevertronics CleverEVAC LP UltraBlade DYGC UP Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics LP Cleverfit Pro CCFPRO Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 LUBPRO Series Manuel

Clevertronics

Clevertronics GLIDER-SM Instructions d'installation et d'utilisation

Clevertronics

Clevertronics Argonaut PLUS Guide de maintenance et de service

Clevertronics

Clevertronics L10 LUBPRO Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics LP CWSQLED Series Manuel utilisateur

Clevertronics

Clevertronics LP CWP2LIFE-PRO-WPPOD Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 CleverFit Exit LCFLED Series Manuel utilisateur

Clevertronics

Clevertronics FBKLED Series Mode d’emploi

Clevertronics

Clevertronics CLP CCIRC Series Manuel

Clevertronics

Clevertronics L10 LBS2N Series Mode d’emploi

Clevertronics

Clevertronics L10 LVP2LEDM-P Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 LIFELIGHT PRO Manuel utilisateur

Clevertronics

Clevertronics CLP Argonaut ARGOSQ-LP Series Manuel utilisateur

Clevertronics

Clevertronics TS EUBPRO-LI Instructions d'installation et d'utilisation

Clevertronics

Clevertronics EJELED-40-LI Instructions d'installation et d'utilisation

Clevertronics

Clevertronics Nifty Lifelight Surface Mount Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 Argonaut PLUS Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur