Clevertronics LP Argonaut Mode d’emploi

1942489

V1.5

24 March 2023

Instruction Sheet Template - V1.1 – Updated 23/11/2020

Clevertest Plus

Refer to the supplementary operation guide supplied with the Product.

After Power ON, the Status LED on a Clevertest Plus enabled fitting will display a rapid Green or Red

flashing for a period up to 2 minutes.

Zoneworks, HIVE (HV/HVG) and DATA Monitored Options

Fittings with part numbers -ZW, -HV, -HVG, -DATA are fitted with Zoneworks communications modules

(nodes). These fittings are monitored using either Powerline Carrier Technology that utilize the power

cable to provide data communication, RF transceiver modules operating in the ISM band or a dedicated

data cable to/from data routers installed on a dedicated data trunk connected to a central Server (can also

be connected via Ethernet/Internet/Fibre). Zoneworks software on the server is used to monitor,

coordinate testing and collate test data from each fitting. Zoneworks Fittings can be commissioned by a

single push of the test switch or by scanning the supplied barcode. The LED Test Switch indicator provides

a multifunction indication of the status of the fitting during testing and normal operation:

Option

State

LED Operation

ZW, HV, HVG,

DATA

Commissioned LED on Solid (Green)

ZW, DATA Un-commissioned

Batt plugged-in: yellow 1s, green 1s

Batt unplugged: red 1s, off 1s

HV, HVG Un-commissioned

With network connectivity

Batt plugged-in: yellow 1s, green 1s

Batt unplugged: red 1s, off 1s

HV, HVG Un-commissioned

Without network connectivity

Batt plugged-in: yellow 250mS, green

250mS, yellow 250mS, green 250mS,

green 1s

Batt unplugged: red 250mS, off

250mS, red 250mS,off 250mS, off 1s

ZW, DATA

Emergency Light Test In Progress

LED flashes at yellow 5s , 0ff 1s

HV, HVG

Emergency Light Test In Progress

LED flashes at yellow 1s , 0ff 1s

In the case of the DATA version a 2-way “figure 8” cable and terminal block facilitates the connection to

the DATA network via a multi-drop bus (daisy chain connection). For further information of installation of

a Zoneworks system, please refer to the Zoneworks Users Guide and Commissioning Guide (incl. DATA

version)

DALI EM Option

Luminaires with part numbers having -DALI are fitted with DALI modules (nodes) that facilitate connection

and integration to 3rd Party Lighting Control Systems. Before installing the -DALI luminaire, please confirm

that the Lighting Control System has the capability to monitor DALI Emergency Luminaires. The -DALI

fitting will be addressed and configured into the control system by the Lighting Control System

Commissioning Technicians and not Clevertronics.

State

LED Operation

Commissioned/ Un-commissioned LED on Solid (Green)

Emergency Light Test in progress

LED flashes at 1s On (Yellow) & 1s Off

“IDENTIFY COMMAND” Lamp and Status LED Flash for 30 seconds

A 2-way “figure 8” cable and terminal block facilitates the connection to the DALI network. DALI

connections are marked as Da Da.

Driver Setting:

For non -SEN / -DD products

Note:

This luminaire (with reinforced insulation between control/LED terminal and AC supply) contains non-

user replaceable light source and battery - to be replaced (if required, refer installation instructions for

battery replacement) by Clevertronics service personnel/agents or a registered electrician.

LP™ Argonaut Square LED Emergency Light

Installation & Maintenance Instruction Leaflet

Victoria (Head Office & Manufacturing)

Website: www.clevertronics.com.au

Email: info@clevertronics.com.au

Phone: +61 3 9559 2700

Fax: +61 3 9559 2799

New South Wales

Phone: +61 2 8805 6400

Fax: +61 2 8805 6444

Queensland

Phone: +61 7 3442 9700

Fax: +61 7 3442 9777

South Australia/Northern Territory

Phone: +61 8 8301 8800

Fax: +61 8 8351 8286

Western Australia

Phone: +61 8 9207 0000

Fax: +61 8 9207 0088

New Zealand

Phone: +64 800 548 448

Designed in Australia to comply with the requirements

of AS2293.3: 2018 and AS/NZS CISPR15: 2017

NOTE: Standard product codes with this symbol are

enabled with Clevertest Plus capability. Please refer to the

operation guide supplied with the product for details.

Models:

ARGOSQ-yy-LP-zz-vv

Testing:

Options:

Manual Test

zz = Blank

Microwave Sensor Hi/Lo Control

yy = SEN

Zoneworks

zz = ZW

Microwave Sensor ON/OFF

yy = MS

Z/W DATA

zz = DATA

Black Body

vv = BLK

Zoneworks HIVE

zz = HV/HVG

DALI Registered.

zz = DALI

Spare Parts:

1550230

Replacement Battery

8050785

Replacement LED Board

AUM02370390001

Replacement Emergency Driver

AUM02970040001

Replacement Emergency Driver (-HVG)

1330094

Replacement 240V Driver (-MS)

1330095

Replacement 240V Driver (-SEN)

1190312

Replacement Microwave Sensor (-MS)

Important:

It is illegal for anyone, except for a licensed electrician to install or maintain this product. Before installation,

ensure that the electricity supply has been switched off and isolated. Installation must be carried out in

accordance with the relevant Australian and International Standards.

1942489

V1.5

24 March 2023

Instruction Sheet Template - V1.1 – Updated 23/11/2020

Installation:

The LP Argonaut Square can be installed either Ceiling or Wall Mounted.

•Remove the four (4) screws holding the diffuser to the base.

•Remove the four (4) screws holding the gear tray to the base.

•Determine the cable access point. There are 2 locations on opposite sides of the fitting for cable

gland/conduit entry. Entry can also be from the back of the base. Drill out the desired cable entry

point.

Note: Only round cables are to be used with the cable gland for an IP65 seal. Keep cable entry

straight and tension free. Ensure all seals are tight.

min. wire diameter 7mm, max. 12mm.

•Drill out 4 of the mounting points in the base (see image below).

•Using the base as a guide, mark the 4 holes for mounting and one for mains access if using back

cable entry.

•Mount the base using appropriate fixings and seal these fixings with appropriate sealant (also fill any

additional entry points).

•If Wall Mounted, then the installation should take place in a manner such that the Status LED is at

the bottom where it will be visible to an observer standing directly below the luminaire.

•Route the power inside the base.

•Connect the 240VAC (Lem,E,N,Lsw) supply to the terminal block of the gear tray. For fittings with

the -MS option, connect the power inputs to LEMG, E, N, LSEN terminals. Slave fittings can be

controlled via the Microwave Sensor by powering them through the output terminal SW (Live).

•Install the gear tray to the base.

•Apply power to the fitting and test per the instructions.

•If the CTP capabilities are activated, please affix the CTP status label to a visible surface and

Four Segment Marking on the product will include an ‘’F’’ in third segment block

Dimensions:

Networking:

When installing the product on a monitored network, (ZONEWORKS, HIVE, DATA, DALI) simply insert

the relevant Smart Node PCA.

Testing:

Once connected to the 240V mains supply, the unit must be allowed to charge the battery for at least 24

hours. Conduct the following tests:

•For the first test, the emergency lamp must remain illuminated for at least 2 hours after

disconnection from the mains supply.

•Subsequent tests require the unit to illuminate for at least 90 minutes. The results of all tests are

required to be recorded in a service logbook, which is to be kept on-site at all times. If the unit fails

to remain illuminated for the requisite time, remedial action must be taken to repair the situation

and once completed, the unit must pass a subsequent test. For more specific information, please

refer to the current edition of the AS 2293.3 Standard.

Maintenance:

Lamp Replacement:

•Use only the lamp(s) recommended on the

label inside the Argonaut.

•To replace the LED Panel, remove the

clips, disconnect the signal cable and install

the new Lamp Panel.

Battery Replacement:

•Use only the battery recommended on the

label inside the Argonaut and on this

instruction.

•Remove the fasteners holding the battery,

un-plug the lead from the PCB and remove

the old battery.

•Attach the new battery, route the DC cable

to the PCB and plug the new battery.

Trouble Shooting:

Below are a list of common problems and their

possible causes.

Fault: The Green LED Test Switch

indicator is not illuminated.

Check: A.C. is connected and is turned on.

Battery is connected

Test Switch for damage.

Fault: Lamp does not illuminate in

emergency mode.

Check: A.C. is connected.

Lamp is correctly inserted.

Battery is connected

Fault: Lamp illuminates in emergency

mode, but only stays on for a short

period.

Check: Battery has been allowed to charge for

at least 24 hours.

Battery for damage.

Rated Emergency Lumen Output in accordance with AS2293.1 (refer to

spacing tables for installation positions):

Refer to the Technical Label for classification information.

Caution:

On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during

construction. As a result, any Exit & Emergency Units, on these circuits, will have their batteries

discharged or “cycled”. The battery in this fitting has been selected to give excellent long-life

performance in a controlled AS2293 testing environment. Excessive battery cycling will reduce through-

life performance and may lead to premature battery failure. Battery warranty claims, as a result of such

abuse, are specifically EXCLUDED from Clevertronics warranty terms.

Warranty:

For Product Warranty information and Terms and Conditions of Sales please refer to our website

http://clevertronics.com.au/terms-conditions-sale-australia-nz/

Ce manuel convient aux modèles suivants

Autres manuels Clevertronics Équipement d'éclairage

Clevertronics

Clevertronics L10 LIFELIGHT PRO LWPLIFE-PRO-CM Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 LJWELED-40 Series Manuel utilisateur

Clevertronics

Clevertronics L10 LUBPRO Series Manuel

Clevertronics

Clevertronics L10 Cleverfit LCFLED Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics TS Trade Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics CleverEVAC L10 Cleverfit Pro DYRL CP Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 Cleverfit Pro LCFPRO-TH Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 Supalite LFLLED Series Manuel utilisateur

Clevertronics

Clevertronics LP Cleverfit CCFLED Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 Weatherproof Jumbo LED Exit Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 Cleverfit Pro Instructions d'installation et d'utilisation

Clevertronics

Clevertronics LP Ultrablade Pro CUBPRO Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics Trade Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 LLIFE-PRO-WP-IPREM Instructions d'installation et d'utilisation

Clevertronics

Clevertronics LP LIFELIGHT PRO CLIFE PRO-SMC Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 Cleverfit Pro Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 Argonaut PLUS Manuel utilisateur

Clevertronics

Clevertronics L10 Lifelight Pro LWPLIFE-PRO-WM Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics LP CFLLED Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 LBLLED-REC-WM Series Caractéristiques techniques

Clevertronics

Clevertronics FVP2LED-P Series Guide de maintenance et de service

Clevertronics

Clevertronics LP CWP2LIFE-PRO-WPPOD Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 LWPLIFE PRO Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics LP Argonaut PLUS Instructions d'installation et d'utilisation

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur