Clevertronics L10 LUBPRO Series Instructions d'installation et d'utilisation

1943039

V1.1

21 March 2019

Zoneworks and DATA Monitored Options

Ultrablades with part numbers LUBPRO-ZW, LUBPRO-DATA are fitted with Zoneworks communications

modules (nodes).These fittings are monitored using either Powerline Carrier Technology that utilises the

power cable to provide data communication or a dedicated data cable to/from data routers installed on a

dedicated data trunk connected to a central Server (can also be connected via Ethernet/Internet/Fibre).

Zoneworks software on the server is used to monitor, coordinate testing and collate test data from each

Ultrablade and can be commissioned by a single push of the test switch, or scanning of the supplied

barcode. The LED Test Switch indicator provides a multifunction indication of the status of the Ultrablade

during testing and normal operation:

State

LED Operation

Commissioned LED on Solid (Green)

Un-commissioned LED flashes at 0.5Hz (0.5s Green, 0.5s Yellow)

Emergency Light Test In Progress LED flashes at 3s On (Yellow) & 0.5s Off

In the case of the DATA version a 2-way “figure 8” cable and terminal block facilitates the connection to

the DATA network via a multi-drop bus (daisy chain connection). For further information of installation of

a Zoneworks XT system, please refer to the Zoneworks Users Guide and Commissioning Guide (incl.

DATA version)

DALI EM Option

Ultrablades with part numbers LUBPRO-DALI are fitted with DALI modules (nodes) that facilitate

connection and integration to 3rd Party Lighting Control Systems. Before installing the LUBPRO-DALI

please confirm that the Lighting Control System has the capability to monitor DALI Emergency Luminaires.

The LUBPRO-DALI will be addressed and configured into the control system by the Lighting Control

System Commissioning Technicians and not Clevertronics.

State

LED Operation

Commissioned/ Un-commissioned LED on Solid (Green)

Emergency Light Test in progress LED flashes at 1s On (Yellow) & 1s Off

“IDENTIFY COMMAND” Fitting goes into emergency mode for 10 seconds

A 2-way “figure 8” cable and terminal block facilitates the connection to the DALI network. DALI

connections are marked as Da Da.

Clevertest and Clevertest Plus

Refer to the supplementary operation guide supplied with the Product.

After Power ON, the Status LED on a Clevertest Plus enabled fitting will display a rapid Green or Red

flashing for a period up to 2 minutes.

Caution:

On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during

construction. As a result, any Ultrablade Units, on these circuits, will have their batteries discharged or

“cycled”. The Li-ion battery in the Ultrablade has been selected to give excellent long life performance in

a controlled IEC 60598-2-22 testing environment. Excessive battery cycling will reduce through-life

performance and may lead to premature battery failure. Battery warranty claims, as a result of such

abuse, are specifically EXCLUDED from Clevertronics warranty terms.

L10™ Ultrablade Pro Recessed LED Exit

Installation & Maintenance Instruction Leaflet

NOTE: Standard product codes with this symbol

are enabled with Clevertest Plus capability. Please refer to the

operation guide supplied with the product for details.

Australia (Head Office)

195 Chesterville Rd

Moorabbin VIC 3189

Phone: +61 3 9559 2700

E-Mail: support@clevertronics.com.au

IP20

UK OFFICE

362 Stockley cl

West Drayton UB7 9BL

Models:

LUBPRO-xx

Testing Options:

Manual Test

xx = Blank

Zoneworks

xx = ZW

Z/W DATA

xx = DATA

DALI Comp.

xx = DALI

Clevertest

xx = CT

(NOTE: -CT Products supplied with the Clevertest Plus Symbol are activated with Clevertest PLUS

capability. Please refer to the operation guide supplied with the product for details).

Spare Parts:

1530050

BATT: L10 3.3V 2500mAh 70mm lead, no BRKT.

8002178

PCA: UBP LED strip PCB Assy (CT10602-D3)

UKM01370030001

LUBPRO-CKIT-70, Ultrablade Pro, Control Only, L10

Important:

It is illegal for anyone, except for a licensed electrician to install or maintain this product. Before installation,

ensure that the electricity supply has been switched off and isolated. Installation must be carried out in

accordance with the relevant British Standards.

1943039

V1.1

21 March 2019

Installation:

The L10 Ultrablade Pro LED Exit (LUBPRO) is a recessed ceiling mount fitting. The LUBPRO can be

attached directly to any solid surface, or to a ceiling tile with the integrated clamping mechanisms. The

LUBPRO comes with an attached Flex. Please follow the steps below to install the LUBPRO Exit:

•Create a cut-out (350mm x 48mm) in the mounting surface.

•Route the power cord to the mains connection and connect the 240VAC supply.

•Insert the LUBPRO into the ceiling cavity tighten the (4) clamping screws.

•Alternately, fix the LUBPRO to a solid surface using (4) screws through the surface material.

•Install the cover plate.

•Apply power to the fitting and test.

•If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by

the manufacturer or his service agent or a similar qualified person to avoid a hazard.

•This luminaire contains non-user replaceable light source and battery.

•Terminal block not included. Installation may require advice from a qualified person.

•Recommended specifications of terminal block for connecting leads:

−Type of Terminal: Screw Terminal

−Number of Terminals: 2-Pin

−Rated Voltage: 250 V

−Rated Connecting Capacity: 10A

•If the CTP capabilities are activated, please affix the CTP Status Label to a visible surface.

Networking:

When installing the product on a monitored network, (ZONEWORKS, DATA, DALI) simply insert the

relevant Smart Node PCA.

Dimensions:

Luminaire Dimensions: 380mm x 220mm

Cover Plate: 385mm x 67mm

Ceiling Cut-out: 350mm x 48mm

Minimum Depth 80mm

Changing EXIT Legend Inserts

The Ultrablade Pro Exit comes with an assortment of standard legends.

1. To remove the legend, grasp the centre of the bottom trim piece and pull down slightly to expose the legend

edge. See photo.

2. Grasp the bottom edge of the legend and slide the existing legend out of the blade, while working the edges out

along the sides.

3. Slide the new legend into the blade, ensuring to fit the edges into the sides then slide the legend to the top of the

blade. Insert one bottom corner then the other. Slide the legend down into the bottom trim.

Testing Procedure:

When the unit is connected to the un-switched active, it must be allowed to charge the battery for at

least 24 hours. Conduct the following tests:

•The emergency lamp must illuminate for at least 180 min after disconnection from the mains. The

results of all tests are required to be recorded in a service logbook, which is to be kept on-site at all

times. If the unit fails to illuminate for the requisite time, remedial action must be taken to repair the

situation and once completed, the unit must pass a subsequent test.

•Press and hold Test Button or switch Off Mains Supply, check that the emergency lamp is On.

•Release the Test Button or Switch On Mains Supply, check that the emergency lamp is Off (Non-

maintained operation).

Ultrablade Maintenance:

LED Lamp Replacement:

•Use only the LED Strip recommended in the

Spares Parts list of this instruction.

•Disconnect battery from LED driver pack and

cut cable tie to remove.

•Disconnect the signal cable from LED strip,

loosen screw and remove the mains driver

pack.

•Remove 4 self-tapping screws and unclip the

LED strip.

•Install the new LED strip following the above

procedure in reverse.

Battery Replacement:

•Use only the battery recommended in the

Spares List on this instruction.

•Remove the cable ties holding the battery,

un-plug the lead from the battery connector

remove the old battery.

•Plug the new battery into the battery

connector.

•Secure the battery using suitable cable ties

Trouble Shooting:

Below are a list of common problems and their

possible causes.

Fault: The Green LED Test Switch indicator

is not illuminated.

Check: A.C. is connected and is turned on.

Battery is connected

Test Switch for damage.

Fault: Lamp does not illuminate in

emergency mode.

Check: A.C. is connected.

Lamp is correctly inserted.

Battery is connected

Fault: Lamp illuminates in emergency

mode, but only stays on for a short

period.

Check: Battery has been allowed to charge for

at least 24 hours.

Battery for damage.

Warranty:

For Product Warranty information and Terms and Conditions of Sales please refer to our website

https://clevertronics.com.au/warranty-statement/

Ce manuel convient aux modèles suivants

Autres manuels Clevertronics Équipement d'éclairage

Clevertronics

Clevertronics EJELED-40-LI Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 Cleverfit LCFLED Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics LP LIFELIGHT PRO CLIFE PRO-SMC Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 Cleverfit Pro LCFPRO-TH Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 LIFELIGHT PRO LWPLIFE-PRO-CM Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics LP LIFELIGHT PRO Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 LIFELIGHT PRO Instructions d'installation et d'utilisation

Clevertronics

Clevertronics LP LIFELIGHT PRO CLIFE-PRO-SMS-SPOT Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics LP CSBLED Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics ECFLED-LI-TH Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 LBLLED-REC-WM Series Caractéristiques techniques

Clevertronics

Clevertronics LP CUBPRO Series Manuel utilisateur

Clevertronics

Clevertronics L10 LIFELIGHT PRO LLIFE-PRO SPOT Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics LIFELIGHT-2PRO-SMS-600 Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 LIFELIGHT LLIFE-SM Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics Nifty Lifelight Surface Mount Instructions d'installation et d'utilisation

Clevertronics

Clevertronics GLIDER-SM Instructions d'installation et d'utilisation

Clevertronics

Clevertronics l10 LBULKy Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics CLP LIFELIGHT PRO Caractéristiques techniques

Clevertronics

Clevertronics LP Argonaut Mode d’emploi

Clevertronics

Clevertronics L10 LBLLED-REC-WM Series Manuel utilisateur

Clevertronics

Clevertronics L10 LIFELIGHT PRO Manuel utilisateur

Clevertronics

Clevertronics Trade TS CIRCLITE ECLLED Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics LP Argonaut PLUS Instructions d'installation et d'utilisation

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur