Clarke CRWP1 Manuel utilisateur

OPERATING INSTRUCTIONS

GC0311

SEMI-ROTARY HAND PUMP

Model No: CRWP1

PART NO: 7130030

INTRODUCTION

Thank you for purchasing this CLARKE Semi-rotary Hand Pump. This product

has been designed to give long and trouble free service. If however, having

followed the instructions in this booklet carefully, you encounter problems,

take the unit to your local CLARKE dealer.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase. This guarantee is invalid if the product is found

to have been abused, tampered with, or not used for its intended purpose.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission. This guarantee does not effect

your statutory rights.

SPECIFICATION

Dimensions, (Length x Depth x Height): 195 mm x 205 mm x 286 mm

Weight: 8.0 kg

Inlet/Outlet Thread Size: 1” BSP

Max Flowrate (subject to operator input): 22.50 L/min

Suction Lift: 7 m (at sea level)

Max Head: 25 m

Suitable for Pumping: Water, Oil or Diesel

DO NOT USE THIS PUMP WITH PETROL OR EDIBLE OILS

INSTALLATION

1. Remove connecting flanges (11) and remove the paper membranes

used to close off the inlet and outlet openings during transit.

2. Depending upon the intended use, it may be desirable to flush out any

residual oil from inside the pump.

3. Install the pump in a vertical position on a wall or similar

structure, with the outlet (indicated by the raised lettering

e.g. K2) facing upwards as shown (fixing bolts not supplied).

Also, always observe any arrows on the pump cover,

indicating the direction of flow.

• Vertical mounting is essential because the valves close

under gravity and if they cannot close, the pump cannot produce

suction.

4. Fit the wooden handle, by tapping gently to ensure it is a tight fit on the

handle spike. The handle can be repositioned to point in any direction

after removing the shaft end nut (9).

5. Connect any inlet and discharge hose connectors which are compatible

with the 1” BSP connecting flanges of the pump.

MAINTENANCE

1. Ensure that the seal compression nut (3) is sufficiently tight. If not, leakage

can take place from the pump handle shaft.

2. If using the pump for water, and there is a likelihood of freezing when not

in use, drain the pump via the access plug (15).

3. If the pump has been used for pumping any liquid likely to leave chemical

residues, it should be flushed through with clean water after use.

4. If the pump will be unused for extended periods, insert some oil through

the access plug (15) to protect the internal parts.

• Ensure the oil used does not contaminate the medium being pumped.

5. Periodically check that all nuts and bolts are tight.

A wide range of accessories are available from your nearest CLARKE dealer,

including hoses and hose adaptors and couplings.

COMPONENT PARTS

1. HTCRWP101 Flange Bolt & Nut 8. HTCRWP108 Gland Ring

2. HTCRWP102 Cover Bolt & Nut 9. HTCRWP109 Shaft End Nut

3. HTCRWP103 Seal Compression Nut 10. HTCRWP110 Washer

4. HTCRWP104 Wing Piston, Flap & Shaft 11. HTCRWP111 Conn Flange

5. HTCRWP105 Suction Divider, Flaps 12. HTCRWP112 Casing

6. HTCRWP106 Handle & Handle Spike 13. HTCRWP113 Cover

7. HTCRWP107 Gland Packing Set 14. HTCRWP114 Flange Joint

15. HTCRWP115 Access Plug

Table des matières

Autres manuels Clarke Pompe à eau

Clarke

Clarke Hippo4A Mode d’emploi

Clarke

Clarke Strong Arm CS10PRH Manuel d'installation et d'exploitation

Clarke

Clarke CBB75 Mode d’emploi

Clarke

Clarke PTP100 Mode d’emploi

Clarke

Clarke CD1 - 1 Manuel d'installation et d'exploitation

Clarke

Clarke CPP3000B Manuel utilisateur

Clarke

Clarke psp125b Mode d’emploi

Clarke

Clarke IVP13A Manuel d'installation et d'exploitation

Clarke

Clarke PSP195 Mode d’emploi

Clarke

Clarke LEP1A 7260060 Mode d’emploi

Clarke

Clarke CSE400A Mode d’emploi

Clarke

Clarke CBM100SS Mode d’emploi

Clarke

Clarke CPPRSS Manuel utilisateur

Clarke

Clarke STP12 Mode d’emploi

Clarke

Clarke CDDFTP Manuel utilisateur

Clarke

Clarke CWBP300 Mode d’emploi

Clarke

Clarke FP150 Manuel utilisateur

Clarke

Clarke ECP20A3 Mode d’emploi

Clarke

Clarke TAM100 7230035 Manuel d'installation et d'exploitation

Clarke

Clarke CSE400A Manuel d'installation et d'exploitation

Clarke

Clarke DWP400A Mode d’emploi

Clarke

Clarke HSEC651A Mode d’emploi

Clarke

Clarke EBP1100 Mode d’emploi

Clarke

Clarke CFTP12 Mode d’emploi

Manuels Pompe à eau populaires d'autres marques

Neptun

Neptun NPHW 5500 Manuel utilisateur

Sensidyne

Sensidyne Gilian BDX-II Instructions d'installation et d'utilisation

Draper

Draper 47808 Manuel utilisateur

Trolla

Trolla 12820 Manuel utilisateur

Sunfab

Sunfab SVH Series Manuel utilisateur

WilTec

WilTec 50740 Manuel utilisateur

Fieldmann

Fieldmann FVC 5015 EK Manuel utilisateur

Everbilt

Everbilt EFSUB5-122HD Manuel utilisateur

Graco

Graco Husky 3300e Manuel utilisateur

esotec

esotec 101018 Manuel utilisateur

moyno

moyno 2000 CC Manuel utilisateur

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuel utilisateur

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guide de dépannage

DUROMAX

DUROMAX XP WX Series Manuel utilisateur

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuel utilisateur

Franklin Electric

Franklin Electric IPS Manuel utilisateur

Xylem

Xylem e-1532 Series Manuel utilisateur

Milton Roy

Milton Roy PRIMEROYAL Manuel utilisateur