Clarke CDS3 Manuel utilisateur
ASSEMBLY INSTRUCTIONS
GC09/13
DRILL STAND WITH VICE
Model No: CDS3
Part No: 6500224
2
INTRODUCTION
Thank you for purchasing this CLARKE product.
Please read and follow the instructions carefully. In doing so you will ensure
the safety of yourself and others around you, and you can look forward to
the product giving you long and satisfactory service.
Please keep these instructions in a safe place for future reference
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for its intended purpose. Faulty goods
should be returned to their place of purchase. No product can be returned
to us without prior permission.
This guarantee does not effect your statutory rights.
SPECIFICATION
erutaeF noisnemiD
htpeDgnillirDmumixaMmm06
thgieHnmuloCmm005
thgieWgk83.3
)HxWxD(snoisnemiDmm894x061x253
seziSralloCllirDmm34/83
3
COMPONENT PARTS
The component parts of your CDS3 drill stand are shown in fig 1.
• Any electric drill with a standard 43mm diameter neck may be fitted
directly to the head assembly.
• A reducing sleeve is provided, allowing a drill with a 38mm diameter neck
also to be accommodated.
• The depth of travel of the drill may be controlled by using the depth
adjuster. A depth scale is provided so that accurate drilling depths may
be set.
OPERATING LEVER
MOUNTING HOLE
VICE JAW QUICK
RELEASE
DEPTH ADJUSTER
ROD
DRILL LOCKING COLLAR
WITH REDUCING SLEEVE
LOWER COLLAR
DEPTH SCALE
COLUMN
HEAD ASSEMBLY
CONNECTING ARM
FIG 1
4
ASSEMBLY
1. Insert the column into the base
and secure with the bolt using a
14mm wrench.
• Ensure the column does not
project below the base.
2. Slide the lower collar onto the
column and secure
approximately half way up the
column using the hex key.
3. Slide the head assembly onto the
column.
4. Attach the operating lever to
both the head assembly and to
the connecting arm using the
nut/bolt at one end, using a
10mm wrench and tighten the
hex key loosely at the other end.
5. Always store the hex key in the
clips on the side of the head
assembly.
Fig 2
Column level
with base
Fig 3
Operating Lever
Head
Assembly
Connecting
Arm
Fig 4
5
6. Secure the vice to the base using
two suitable bolts with nuts and
washers (not supplied).
• To position the vice relative to
the column, slacken the two
vice securing bolts and
manoeuvre the vice as
required.
IMPORTANT!
Secure the base to a workbench or sturdy table using suitable bolts (not
supplied). Drill the work-bench/table accordingly, using the four mounting
holes in the stand base as a template.
FITTING A DRILL
1. Fit an electric drill with a
standard 43mm diameter neck to
the head assembly and secure in
the locking collar as shown in Fig
6. Tighten the locking collar using
the hex key.
2. If using a drill with a 38mm neck,
fit the reducing sleeve provided
into the locking collar before
inserting the drill.
SETTING THE DEPTH
1. Decide on the depth of hole
required to be drilled.
2. Release the hex head bolt which
locks the depth adjusting rod.
3. Using the operating arm, lower
the drill until the required reading
is showing on the scale and lock
the depth adjuster rod at this
position using the hex key.
4. It is recommended that a light
smearing of lubricant be applied to the column to assist with free
movement.
Fig 5
Bolt/nut
Fig 6
Hex bolt in
locking collar
Fig 7
Depth
Scale
Depth
Adjusting
Rod
Hex head
bolt
6
DRILLING THE HOLE
1. Lower the head assembly until
the drill bit is just touching the
workpiece as in Fig 8, and set the
head assembly in position using
the hex key shown in Fig 3.
2. Switch the drill on, and press
down on the operating lever as
the drill bit starts drilling. The
depth of hole will be restricted by
the depth stop.
ADJUSTING THE VICE
1. A quick setting button is provided
for the vice jaw adjustment. Press
the red button whilst pushing IN or
pulling OUT the handle.
Fig 8
Fig 9
7
NOTES
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
Table des matières
Autres manuels Clarke Support et étagère
Clarke
Clarke CSM5175 Series Manuel utilisateur
Clarke
Clarke CAX3TAB Manuel utilisateur
Clarke
Clarke CAX3TBC Manuel utilisateur
Clarke
Clarke CMSSR Manuel utilisateur
Clarke
Clarke Strong-Arm CES450 Manuel utilisateur
Clarke
Clarke Strong-Arm CES680 Manuel du propriétaire
Clarke
Clarke CAX6TBC Manuel utilisateur
Clarke
Clarke LB5S Mode d’emploi
Clarke
Clarke CSR4200 Manuel utilisateur
Clarke
Clarke CTS4000B Manuel utilisateur
Clarke
Clarke CWC80B Manuel utilisateur
Clarke
Clarke CMSS Manuel utilisateur
Clarke
Clarke Strong-Arm CES340 Manuel utilisateur
Clarke
Clarke Metalworker CL430 Manuel utilisateur
Clarke
Clarke CWR45 Manuel de programmation
Clarke
Clarke CES680F Manuel du propriétaire
Clarke
Clarke CES560 Manuel utilisateur
Clarke
Clarke CBS3 Manuel utilisateur
Clarke
Clarke CAX3TA Manuel utilisateur
Clarke
Clarke CHT399 Mode d’emploi
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
