Clarke CSJ1500 Manuel utilisateur
USER INSTRUCTIONS
GC0414
1.5 TONNE SCISSOR JACK
MODEL NO: CSJ1500
PART NO: 7624015
2
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
INTRODUCTION
Thank you for purchasing this CLARKE Scissor Jack.
Before attempting to use this product, please read this manual thoroughly and
follow the instructions carefully. In doing so you will ensure the safety of yourself
and that of others around you, and you can look forward to your purchase
giving you long and satisfactory service.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
LIFTING OPERATIONS AND LIFTING EQUIPMENT
REGULATIONS 1998 (LOLER)
This jack, depending on use, may fall within the scope of LOLER. It is the
owner’s responsibility to determine whether or not it does and, if so, to comply
with any applicable requirements in LOLER, for having the jack thoroughly
examined.
SPECIFICATION
Rated Load 1.5 Tonne
Min height of saddle 95 mm
Max height of saddle 390 mm
Length of handle 415 mm
3
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
SAFETY PRECAUTIONS
• Ensure that the jack is in good working order. Have any damaged
parts repaired or replaced immediately. Use genuine Clarke parts
only. The use of unauthorised parts may be dangerous and will
invalidate the warranty.
• Operate the jack in a suitable, well lit work area.
• Keep the work area clean and tidy and free from unrelated items.
• Use the jack on level and solid ground, preferably concrete. Avoid
soft/unmade ground as the jack may sink in.
• Ensure the vehicle handbrake is engaged, the engine/motor is
switched off and the transmission is in 1st or reverse gear. (or park for
automatics)
• Ensure a minimum distance of 0.5 m between vehicle and static
objects such as doors, walls, etc, to allow for the vehicle tilting.
• Only place the jack under those lifting points recommended by the
vehicle manufacturer (see vehicle handbook).
• Check the lifting point is rigid and centred on the jack saddle.
• Ensure there are no passengers in the vehicle.
• Place chocks under the wheels of the vehicle.
• Ensure all non-essential persons keep a safe distance whilst the jack
is in use.
• Use suitable capacity axle stands under the vehicle before
proceeding with any task.
• Ensure there are no personnel or obstructions under the vehicle
before lowering.
•Use the jack for lifting only, NOT for supporting the vehicle.
• Take care not to trap fingers in the moving parts of the jack.
•Do not operate the jack if damaged.
•Do not work under the vehicle until axle stands have been correctly
positioned.
•Do not allow personnel to operate the jack unless they have read
these safety precautions.
•Do not use the jack for purposes other than that for which it is
designed.
4
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
•Do not exceed the rated capacity of the jack.
•Do not jack up a vehicle if there is a risk of spillage of fuel, battery
acid or other dangerous substances.
•Do not allow the vehicle to move while supported by the jack.
•Ensure that you can see the saddle and jacking point throughout
the jacking operation in case there is any relative movement.
• Never tamper with the product or modify it in any way, as this could
prove to be dangerous and will invalidate the guarantee. Only use
the product for the purpose for which it is intended.
• When not in use, store the jack, fully lowered, in a safe, dry,
childproof area.
OPERATING INSTRUCTIONS
1. Prepare the vehicle as mentioned in the safety precautions ensuring the
ground on which the jack is to stand is level and solid.
2. Position the jack saddle under the vehicle manufacturers recommended
lifting point.
3. No responsibility can be accepted for incorrect use of the jack.
Warning: IT IS VERY DANGEROUS TO GO UNDER A VEHICLE WHICH IS
SUPPORTED BY A JACK EVEN IF ADDITIONAL SUPPORTS ARE USED. DO
NOT GO UNDER A VEHICLE UNLESS IT IS SUPPORTED BY ADEQUATELY
RATED AXLE STAND
WARNING: BEFORE LIFTING, ENSURE THE SAFETY PRECAUTIONS ARE
STRICTLY FOLLOWED.
5
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
LIFTING THE VEHICLE
1. Turn the handle clockwise to bring
the jack saddle into contact with
the recommended lifting point.
2. Ensure the jack is vertical before
continuing to turn the handle
clockwise and raising the vehicle
to the required working height.
Turn the handle slowly and evenly
to ensure no sudden movements
of the vehicle.
LOWERING THE VEHICLE
1. Slowly turn the handle anti-clockwise to lower the vehicle.
MAINTENANCE
IMPORTANT: Only fully qualified personnel should attempt maintenance or
repair.
• Keep the jack clean and lubricate all moving parts with oil on a
regular basis.
• Before each use check for broken, cracked, bent, or loose parts, or
any visible damage to welds, saddle, frame and all parts including
pins and other fasteners. If any suspect item is found remove jack
from service and take necessary action to remedy the problem.
• Do not use the jack if believed to have been subjected to abnormal
load or shock. Inspect and take appropriate action.
WARNING: ALWAYS LOWER IN A SLOW AND CONTROLLED MANNER AND
ENSURE THERE ARE NO PERSONS OR OBSTACLES BENEATH THE VEHICLE,
OR IN THE PATH OF ITS DESCENT.
6
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
PARTS LIST & DIAGRAM
No Description No Description
1 Saddle 8 Handle
2 Saddle Rivet 9 Threaded Rod
3 Upper Arm 10 Lower Arm
4 Safety Label 11 Inner Stay
5 Collar 12 Base
6 Hinge 13 Base Rivet
7 Bearing 14 Hinge
7
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
DECLARATION OF CONFORMITY
Table des matières
Autres manuels Clarke Jack
Clarke
Clarke STRONG-ARM CTJ5GLB Mode d’emploi
Clarke
Clarke STRONG-ARM CTJ2B Mode d’emploi
Clarke
Clarke CTJ2CB Mode d’emploi
Clarke
Clarke CBJ32 Mode d’emploi
Clarke
Clarke CGK4 Manuel utilisateur
Clarke
Clarke Strong-Arm CBJ2B Guide de dépannage
Clarke
Clarke CTJ3QLGB Mode d’emploi
Clarke
Clarke Strong-Arm CTJ 50 Manuel d'installation et d'exploitation
Clarke
Clarke CAX2TA Manuel utilisateur
Clarke
Clarke STRONG-ARM CML3 Guide de référence rapide
Clarke
Clarke CTJ3GLS Mode d’emploi
Clarke
Clarke CTJ2001G Mode d’emploi
Clarke
Clarke strong-arm CBJ30 Guide de dépannage
Clarke
Clarke STRONG-ARM CTJ3GLC Manuel utilisateur
Clarke
Clarke CTJ3000C Mode d’emploi
Clarke
Clarke CTJ10GLS Mode d’emploi
Clarke
Clarke CTJ2000G Manuel utilisateur
Clarke
Clarke CTJ1800AB Mode d’emploi
Clarke
Clarke CTT320 Manuel utilisateur
Clarke
Clarke CTJ2500SUV Mode d’emploi
